3167X Magic Chef Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Burners would not lite
2 of 4 people
found this instruction helpful.
-
Lloyd from Cocoa, FL
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
I removed the old module ,replaced new bracket,crimped new wire lugs on wires. being an electrician for 50 plus years helped. Thanks Lloyd
Was this helpful?
Thank you for voting!
Oven shutting off, getting an F1 error on ECM
2 of 4 people
found this instruction helpful.
-
Ben from Belen, NM
- Really Easy
- 15 - 30 mins
-
Screw drivers
Remove rear sheet metal cover. Disconnect the temp sensor wiring connector (on the left side as viewed from front).
Open oven, take out the 2 screws attaching sensor and remove. Reverse for installation.
Included wiring adapters are not needed for this model oven.
Open oven, take out the 2 screws attaching sensor and remove. Reverse for installation.
Included wiring adapters are not needed for this model oven.
Was this helpful?
Thank you for voting!
Igniter for oven not working
1 person
found this instruction helpful.
-
RONNIE from SAG HARBOR, NY
- Easy
- Less than 15 mins
-
Wrench set
Instead of buying a new range my son said he could replace the part so I looked your company up on internet and had it shipped. Three days later I was cooking with gas again! Thanks!
Was this helpful?
Thank you for voting!
oven would not light reliably.
1 person
found this instruction helpful.
-
Joe from West Winfield, NY
- Easy
- Less than 15 mins
-
Screw drivers
Just like the example I removed the oven base, removed the two screws holding the igniter. Pulled out the wires opened the connector, plugged in the new igniter put everything back and turned on the oven. The oven now lights better than it did when new. And it holds a steady temp.
Was this helpful?
Thank you for voting!
igniter failed to ignite
1 person
found this instruction helpful.
-
Gino from ARLETA, CA
- Really Easy
- Less than 15 mins
-
Socket set
Replaced the igniter by removing 2 screws, pulling on the wires to pull the connector in from the back thru the oval opening, screwing in the the new element, reconnecting the wires, pushing the connector back and that did it.
Was this helpful?
Thank you for voting!
Oven was not working at all
1 person
found this instruction helpful.
-
Glynne from Dedham, MA
- Easy
- 1- 2 hours
-
Pliers, Screw drivers, Wrench (Adjustable)
My brother is a handyman. The part was delivered very quickly. The instructions were very easy to read and after an hour, voila the oven works perfectly!
Was this helpful?
Thank you for voting!
Replaced upper over light and assembly
1 person
found this instruction helpful.
-
Thomas from SAN DIEGO, CA
- Very Difficult
- More than 2 hours
-
Pliers, Screw drivers
I had to pull out the oven and balance the oven on two patio tables. Remove the back of the oven. Pull out the light assembly which was burnt. I was unable to remove the casing around the light, so I destroyed it with a pliers. Reinstalling the new light and assembly was easy. What made this job difficult, I could not remove the light ass
... Read more
embly from the front of the oven and had to go in from the back.
Read less
Was this helpful?
Thank you for voting!
oven took too long to light, then lit with a whump sound
1 of 2 people
found this instruction helpful.
-
Steve from Sierra Madre, CA
- A Bit Difficult
- 1- 2 hours
-
Pliers, Screw drivers
I read all the reports on your site pertaining to oven igniters and decided to order one. I was amazed when it arrived the next day. I got a lot of tips reading others replys so I lifted off the oven door, took out the racks, removed the 2 screws holding the old igniter and tried to pull it out. There was hardly any slack in the wires, so
... Read more
I pulled the stove away from the wall, took off a breadpan size cover in back and found the wires were zip tied to a tube. I cut the tie and unplugged the wires, but the new plug didn't match so I cut the new plug off and rejoined the wires with butt to butt crimp connecters, which I prefer to wire nuts. I used the insulation and new cover from your kit as my old part had the long ceramic insulator and put it all back together. It works like new again and saved me a lot of money. I am very pleased with your product and service, thanks.
Read less
Was this helpful?
Thank you for voting!
Bottom oven burner wouldn't light.
1 of 2 people
found this instruction helpful.
-
James from Lino Lakes, MN
- Easy
- Less than 15 mins
-
Nutdriver
If your igniter glows but the burner doesn't light, your igniter is more than likely bad. It should have at least 3.2V to gas valve when the igniter is glowing in order to open the gas valve. The repair is very easy with only a 5/16" nut driver equired to remove and replace the igniter. It's pretty much a plug and play reair.
Was this helpful?
Thank you for voting!
Oven wouldn't heat. Igniter was broken.
1 of 2 people
found this instruction helpful.
-
Thomas from Allison Park, PA
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers, Socket set
I removed the back of the range to disconnect the wires to the igniter. Then I removed the two screws holding the igniter, screwed the new one in and reconnected the wires in back.
I was really pleased how easy it was to find the part on the website and how quickly the part came. The whole job was a snap. Thanks!
I was really pleased how easy it was to find the part on the website and how quickly the part came. The whole job was a snap. Thanks!
Was this helpful?
Thank you for voting!
Thermostat bulb was hanging loose
2 of 5 people
found this instruction helpful.
-
Willi from Old Saybrook, CT
- Really Easy
- Less than 15 mins
-
Pliers
Removed what was left of the original clips. Pressed in the new clips and snapped in the themostat blub
Was this helpful?
Thank you for voting!
Oven Ignitor went to ignitor heaven.
1 of 2 people
found this instruction helpful.
-
Brian from Pittsburgh, PA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Socket set
The repair was real easy, other than the old bolts which just turned in the sockets when trying to get them out. It might be a good idea to provide two nuts and bolts to negate this problem. I would not mind paying a dollar or two extra for two bolts and nuts. Other than that, the instructions were clear. Product arrived on time and I wou
... Read more
ld absolutely use your services again. Oven is back to working great! Thank you!
Read less
Was this helpful?
Thank you for voting!
Igniter Would Glow But Stove Wouldn't Light
1 of 2 people
found this instruction helpful.
-
ALAN from LUCK, WI
- Really Easy
- 15 - 30 mins
-
Nutdriver
I noticed that the ignitor would glow but the stove wouldn't light - I got the model number of the stove and googled the maytag model number. Came upon your website and realized that 94% of the time the problem was the amps were not enough to light the stove. I looked at all of the stories on how easy it was to fix. I ordered the pa
... Read more
rt and received it within 3 days. I opened the door part way and lifted it straight up to remove it. I pulled out the bottom broiler plate by grabbing the back on pulling up. I undscrewed the wing nut of the flame bar and had easy access to the igniter. I removed the two nuts from the old igniter. Unplugged the igniter from the easy access door from the back and plugged in the new igniter. Replaced the access door and attached the igniter with the two nuts. Put the flame bar back on, put the broiler plate back on, put the door back on, plugged in the stove turned it on and success. It was so easy. I know in our area I would have paid near $200 for a service technician to come out and do what I did in approx. 20 Minutes and $50 for the part. Thank you so much for you website to help us not so talented appliance repair homeowners.
Read less
Was this helpful?
Thank you for voting!
Oven did not ignite
1 of 2 people
found this instruction helpful.
-
John from Racine, WI
- Really Easy
- 15 - 30 mins
-
Screw drivers
Remove the door... it just pulls up and out... set the release tabs so you can remove the bottom plate .. pull out broiler drawer... unscrew the 2 screws on the igniter ..let that hang... remove the cover for the termination.. and unplug the old igniter... then reverse everything to put back together..
Was this helpful?
Thank you for voting!
Oven Wouldn't Light. Smell Of Gas Before Lighting
1 of 2 people
found this instruction helpful.
-
Charles from Alexandria, VA
- Really Easy
- Less than 15 mins
-
Nutdriver
First I went online to find out about the availability of the part. In my search, I found what others had experienced and how they repaired it. Second, I ordered the part and followed others stories on their repair efforts. Third, I unplugged the range and removed the racks. Fourth, I removed the bottom of the oven which lifts out bac
... Read more
k first. Fifth, I removed the wing nut securing the flame difusser making it easier to access the element. Sixth, I had read that others had problems saving the original screws and/or threaded holes. I sprayed some wd-40 on both screws. They came out and back in without a hitch. Seventh, I removed and replaced the element, snap out, snap in. Eighth, I turned on the oven. It took about 15 seconds to glow but wow, it lit 5 seconds after that. I am my wife's hero!
Read less
Was this helpful?
Thank you for voting!