3167X Magic Chef Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
floor panel heavily stained and warped
3 of 5 people
found this instruction helpful.
-
Joel from Monroe, NY
- Really Easy
- Less than 15 mins
slide latches in rear of floor panel forward and remove.
Was this helpful?
Thank you for voting!
Replacing the bulb in the freezer side
5 of 11 people
found this instruction helpful.
-
Yafa (and David) from Bothell, WA
- Easy
- Less than 15 mins
-
Nutdriver
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this helpful?
Thank you for voting!
Igniter glowed but oven would not light
2 of 2 people
found this instruction helpful.
-
Richard from West Mifflin, PA
- Easy
- Less than 15 mins
-
Nutdriver
The repair was straight forward. Turn off gas, unplug stove. Remove the oven door by opening slightly and lifting straight up. The bottom plate lifts from the back. Remove two screws and plug; install new unit. Turn everything back on; proceed with baking...
Was this helpful?
Thank you for voting!
Couldn't Read the oven Temp on knob.
2 of 3 people
found this instruction helpful.
-
David from Winfield, IL
- Really Easy
- Less than 15 mins
-
Screw drivers
Called Magic Chef for part and they said the oven was to old. Looked up Partselect.com and found part I needed. Shipped fed ex and pull off knob, unscrewed old skirt, clean area, screwed on new part and replace knob. Looks like a new stove.
Unbelievable that Magic Chef didn't know about this site. I will always check here first for ... Read more what I need.
Dave
Illinois
Unbelievable that Magic Chef didn't know about this site. I will always check here first for ... Read more what I need.
Dave
Illinois
Read less
Was this helpful?
Thank you for voting!
I needed a broiler pan
4 of 9 people
found this instruction helpful.
-
Rhoda P. from Secaucus, NJ
- Really Easy
- Less than 15 mins
I took the broiler pan out of the shipping container and put it in the oven.
Other Parts Used:
Was this helpful?
Thank you for voting!
Had an F2 message go off then F3 when I tried to turn the stove on
2 of 3 people
found this instruction helpful.
-
Daniel from MOUNT HEALTHY, OH
- Very Easy
- Less than 15 mins
-
Screw drivers
Unplugged the old temp sensor at the back of the stove. From the inside I removed the 2 retaining screws. I taped a string to the old wire and pulled it through so I could pull the new harness through on the new sensor. When the new sensor arrived I installed it in reverse order. Easy peasy. Works great!!!!
Was this helpful?
Thank you for voting!
Replace clock-adjust knob
2 of 3 people
found this instruction helpful.
-
OSCAR from BRISTOL, CT
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers
Although normally a push fit, we drilled and tapped a #6-32 cross hole and used a set-screw to attach the small knob.
The original knob is still hiding somewhere but, thanks to PartSelect we are back in business !
The original knob is still hiding somewhere but, thanks to PartSelect we are back in business !
Was this helpful?
Thank you for voting!
F 3 signal on display pad every time oven warmed up
2 of 3 people
found this instruction helpful.
-
jeff from haskell, NJ
- Easy
- 15 - 30 mins
-
Screw drivers
Removed all the racks from inside the oven, unscrewed the 6 screws that held it into the cabinet, pulled it out and sat it on the floor in front of the cabinet. Removed the oven sensor from the inside of the oven after disconnecting the wire harness from the rear right exterior of the oven. Installed new sensor from inside (2screws), plug
... Read more
ged it into the harness in the back and reinstalled oven in the cabinet.
Read less
Was this helpful?
Thank you for voting!
Oven did not heat up in bake mode.
2 of 3 people
found this instruction helpful.
-
Peter from Westcliffe, CO
- Easy
- 30 - 60 mins
-
Screw drivers
The ignitor heated up and the broiler worked but not the bake mode. Repaired per instructions
Was this helpful?
Thank you for voting!
igniter glowed but oven would not light
2 of 3 people
found this instruction helpful.
-
edward from euclid, OH
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Screw drivers
It looked like an easy fix. the igniter had a plastic clip. A simple R&R. Removed old igniter from its mount, removed plate to get access to wires, removed insulation. Tried to pull the old wires out of its location. It was hung up and I spent 1/2 hr. trying to free it. No go. I thought I'd have to remove oven from its cabinet. I removed
... Read more
six screws and it would not come forward. I felt the under side of the oven thru lower door of cabinet and found out that was where gas was connected. No way was I disconnecting the gas. Pushed oven back in, reinstalled screws and decided to cut old wires and splice in the new igniter. WENT BACK AND READ THE INSTRUCTIONS! Supplied were 4 ceramic wire nuts. Then the light bulb went on! OKAY! I got a marker and marked the top wire on the old igniter to identify it after I cut the wires as close to the back of the old igniter as I could with a pair of side cutters. I then cut the wires as close as I could to the plastic clip on the new igniter. Striped off 3/8 in. from all wire ends and spliced the wires together using the wire nuts. I stuffed the wires as far as possible back into the hole they came from, replaced all old and some new insulation into the hole. The supplied cover would not work, screw holes would not line up and would have fit poorly. I reused the old hole cover. Screwed new igniter to its mount. Turned on the oven and thought I screwed up. I waited about 30 seconds before I saw it start to glow. WHEW! I got it right! After a few more seconds, the gas came on and the oven burner ignited. The really hard part was putting the oven door back on its mount. That door was heavy and wouldn't line up on the first try.......
Maybe if I read the instructions thoroughly the first time before I started, I could have cut my time in half and saved a lot of cussin'. CUTTING THE WIRES WAS AN "OPTION"! That's why they supplied the ceramic wire nuts!....... Dinner is in the oven right now. Smells good!
Maybe if I read the instructions thoroughly the first time before I started, I could have cut my time in half and saved a lot of cussin'. CUTTING THE WIRES WAS AN "OPTION"! That's why they supplied the ceramic wire nuts!....... Dinner is in the oven right now. Smells good!
Read less
Was this helpful?
Thank you for voting!
oven would not turn on
2 of 3 people
found this instruction helpful.
-
Robert from Clymer, NY
- Easy
- 15 - 30 mins
-
Screw drivers
I first removed oven racks.then I removed bottom of oven by sliding locks,then lifting out bottom.Next I removed screw holding e. control cove,then removed cover.Igniter plug was exposed,I then unpluged egniter. I next removed 2 screws holding burner and igniter .I removed igniter and burner as a unit. removed 1 screw from igniter,and rep
... Read more
laced igniter on burner.Then assembled every thing in reverse order,and tested Oven worked perfectly.
Read less
Was this helpful?
Thank you for voting!
My oven door seal had dried rotted
1 person
found this instruction helpful.
-
Anita from ELKTON, VA
- Really Easy
- 15 - 30 mins
-
Pliers
I took pliers to get the old one off, and popped the new one back in its place, and it fit perfect.
Was this helpful?
Thank you for voting!
Simply remove and install new parts
1 person
found this instruction helpful.
-
Jacob from LITTLE CANADA, MN
- Really Easy
- 15 - 30 mins
Overall, it was painless and easy with zero problems
Was this helpful?
Thank you for voting!
The oven bottom was warped and could not be positioned properly in the oven.
1 person
found this instruction helpful.
-
Tara from ALBANY, NY
- Easy
- 15 - 30 mins
Removing the old oven bottom was easy...as it was already outside of its slots. Installing the new one was pretty easy. I placed the oven bottom in the front slots first...then the rear slots...no tools necessary.
Was this helpful?
Thank you for voting!
The oven did not heat, but the top burners worked fine.
1 person
found this instruction helpful.
-
Marvin from DECATUR, GA
- Really Easy
- 15 - 30 mins
-
Screw drivers
1. Slowly pull the stove from wall. 2. Unplug 120 volts plug from outlet. 3.Turned off the gas outlet. 4. Open the stove door, remove the racks, then unscrew (2) screws that hold the short oven sensor in place. 5. Slowly pull sensor out of it's housing. Remove the clip that holds the sensor. Install new sensor using the clip. Push sensor
... Read more
back through the hole opening. Screw the (2) screws into the mount to secure the sensor. 6. Plug the 120 volt plug into the wall outlet. Turn on the gas outlet. Test stove by turning on oven. It works like a new stove. Wife is happy, and Thanks Giving Dinner is on! Reverse your steps to secure your stove. A total of 25 minutes after cleaning the dust under stove. Thanks for everything. By the way, Thanks Giving Dinner was delicious.
Read less
Was this helpful?
Thank you for voting!