3137 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
broken shelf end caps- right side of 2 shelves.
2 of 2 people
found this instruction helpful.
-
William from PRESQUE ISLE, ME
- Really Easy
- Less than 15 mins
After watching video I took off end shelf caps. It took close to 10 mins to replace them.
Was this helpful?
Thank you for voting!
light wouldn't come out of socket
3 of 5 people
found this instruction helpful.
-
Joyce from Tacoma, WA
- Really Easy
- Less than 15 mins
It just unpluged and the new one plugged in. Simple. The part was reasonable and arrived very quickly. It sure is nice to have a light in the frig again.
Was this helpful?
Thank you for voting!
The Refridgerator and Freezer were not cooling.
2 of 2 people
found this instruction helpful.
-
Frank from VERO BEACH, FL
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Installing the part repaired the fridge and freezer immediately.
Was this helpful?
Thank you for voting!
Fridge light dead even with new bulb
1 person
found this instruction helpful.
-
marj from NEWBURY PARK, CA
- Really Easy
- 15 - 30 mins
-
Screw drivers
1- youtubed the potential diagnoses, 2- resourced and ordered parts, 3- removed old socket, installed new one :-)... My fridge is an older fridge and could've used a screwdriver for eyeglasses. Plug and play easy... YAY!
Was this helpful?
Thank you for voting!
Old fan broke from previous owner
3 of 7 people
found this instruction helpful.
-
Carmen from APPLE VALLEY, MN
- Easy
- 15 - 30 mins
-
Socket set
Used this an old (maybe a 2007?) Briggs and Stratton 17.5 ho engine.This fan wasn’t an exact replica of the old one. But the bolt holes were in the right spot and it was the right size. Had to drill out the little dimples for the bolts and the fan guard that goes on top to stop debris didn’t screw directly into the fan like the old one. B
... Read more
ut I was able to attach the guard to the engine cover/piece that houses the air filter with a plastic bracket/retainer that was already on the engine. Overall, easy install and fit just fine once I determined how I wanted to attach the fan guard
Read less
Was this helpful?
Thank you for voting!
water leaking from under dishwasher
1 person
found this instruction helpful.
-
Edward from E LONGMEADOW, MA
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Socket set, Wrench (Adjustable)
Water was leaking from under the GE dishwasher, but once we pulled it out, had apparently been going on for a little while. Turning the water off to the dishwasher made it stop, so it was happening even when the unit was not running, potentially indicating somewhere early in the path of the water to and into the machine.
Indeed ... Read more , inspecting the water inlet vale showed a slow leak. Getting the replacement part was fine, and it fit the electrical, water inlet (existing 90-degree water inlet elbow), and water outlet connections just fine - but the original machine screws that held on the original water inlet valve did not work. It took a little research to figure out the new type of screw required, which was apparently a 10/16 Type AB, which seemed to be a less common type of sheet metal screw (with a point), as opposed to the original flat-ended machine screws. So, after ordering those separately (which were a bit expensive), it went together fine.
A note on the water inlet valve part just indicating the the threading on those parts has changed over time, so potentially ordering the screws to attach it might be worthwhile, would be good information to add about the water inlet valve.
Indeed ... Read more , inspecting the water inlet vale showed a slow leak. Getting the replacement part was fine, and it fit the electrical, water inlet (existing 90-degree water inlet elbow), and water outlet connections just fine - but the original machine screws that held on the original water inlet valve did not work. It took a little research to figure out the new type of screw required, which was apparently a 10/16 Type AB, which seemed to be a less common type of sheet metal screw (with a point), as opposed to the original flat-ended machine screws. So, after ordering those separately (which were a bit expensive), it went together fine.
A note on the water inlet valve part just indicating the the threading on those parts has changed over time, so potentially ordering the screws to attach it might be worthwhile, would be good information to add about the water inlet valve.
Read less
Was this helpful?
Thank you for voting!
Start relay burned
1 person
found this instruction helpful.
-
Carlos from Copper Canyon, OK
- Very Easy
- 15 - 30 mins
-
Screw drivers
Unplug the refrigerator removed the condenser/ compressor cover back bottom on fridge, remove the relay from the compressor took off the two wires, replace with new relay
Was this helpful?
Thank you for voting!
My light in the refrigerator was going on and off.
1 person
found this instruction helpful.
-
Nan from PURCELLVILLE, VA
- Very Easy
- Less than 15 mins
I unplugged the refrigerator. Pressed the tab near the light bulb. Unplugged the socket and reconnected it.
Was this helpful?
Thank you for voting!
The light inside the oven had burned out
3 of 7 people
found this instruction helpful.
-
Catherine from SEATTLE, WA
- Very Easy
- Less than 15 mins
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
... Read more />3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
... Read more />3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Read less
Was this helpful?
Thank you for voting!
bulb out
1 person
found this instruction helpful.
-
Kenneth from Rowe, VA
- Really Easy
- Less than 15 mins
I ordered the part, within two days we had received it. My husband put the part in and I really don't know what he used doing so. All I know is that the light works now and we don't have to use the flashlight. Thanks a lot.
Was this helpful?
Thank you for voting!
Lights did not work, bulbs were good
1 person
found this instruction helpful.
-
Donita from O FALLON, MO
- Easy
- Less than 15 mins
-
Screw drivers
Took out the light sockets, plugged in the new ones. I found the manual on line to find the part numbers. Parts select parts were perfect
Other Parts Used:
Was this helpful?
Thank you for voting!
Door shelf clip had broken
1 of 2 people
found this instruction helpful.
-
Erika from Joliet, IL
- Really Easy
- Less than 15 mins
This shelf has been broken for about a year now and my husband tried several little quick fixes that would work for a while and then the shelf would fall again. A quick search online led me to your website, the part arrive within two days, and the shelf was fixed in less than ten minutes. It's working great. We'll definitely keep you in m
... Read more
ind for the future.
Read less
Was this helpful?
Thank you for voting!
The control board generated clicking noise. Temperature display wrong values.
1 of 2 people
found this instruction helpful.
-
QUOC-LOC from LYNN HAVEN, FL
- Really Easy
- 30 - 60 mins
-
Screw drivers
On the internet forum I read that if the control board needs to be changed , do the same for the Run Capacitor/relay.
The Ge profile refrigerator was 15 years old. First I disconnect the power cord,
I removed the control board at the back of the fridge, replaced it with a new one and did the same for the run capacitor.
P ... Read more lugged the power cord back and it works fine. GE repair service did not want to come to do it. DIY is fine.
The Ge profile refrigerator was 15 years old. First I disconnect the power cord,
I removed the control board at the back of the fridge, replaced it with a new one and did the same for the run capacitor.
P ... Read more lugged the power cord back and it works fine. GE repair service did not want to come to do it. DIY is fine.
Read less
Was this helpful?
Thank you for voting!
Change bulb
3 of 8 people
found this instruction helpful.
-
Louis from LEAGUE CITY, TX
- Really Easy
- 30 - 60 mins
-
Nutdriver
Easy
Was this helpful?
Thank you for voting!
Short in the light socket.
1 of 2 people
found this instruction helpful.
-
ED from ENON, OH
- Very Easy
- Less than 15 mins
Un Plugged the frig. Unlocked the socket by pressing down on the latch. Pulled the socket out ensuring I had enough slack. Unplugged the old socket installed the new. Plugged the frig back in. Tested the switch . Very easy-to-use.
Was this helpful?
Thank you for voting!