EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3127 - Instructions

All Instructions for the 3127
76 - 90 of 428

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven wouldn't heat/ turn on
3 of 3 people found this instruction helpful.
  • Diane from NEW HAVEN, MO
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
If you watched the video on installing the part it IS that easy. The connector piece matched exactly with what my oven already had so it was as simple as disconnecting the old piece and plugging in the new piece. There was no hidden challenges or obstacles to overcome. The oven works perfectly fine there was a slight smell when I first turned on the oven but I am attributing that to a new part. The smell did go away. I am 24 years old and a female who has limited knowledge in electrical/oven work.
Was this helpful?
Thank you for voting!
No spark, bad igniter
3 of 3 people found this instruction helpful.
  • Tom from REDDING, CA
  • Really Easy
  • 15 - 30 mins
1. Grab the old burner and twist counter-clockwise. 2. Unplug the wire from the old igniter, simply pull off. 3. Take new burner/igniter (this new one comes all-in-one) and reattach the wire to the igniter underneath. 4. Place the burner so the 'nubs' line up with the stove top and then twist clockwise a short amount, it should tu rn slightly to lock in place. 5. Test. Mine sparked and started better than it has since i have had the stove
Was this helpful?
Thank you for voting!
Leaking gas from sides of burner
3 of 3 people found this instruction helpful.
  • Homero from SEAGOVILLE, TX
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Wrench (Adjustable)
Counterclockwise turn old burner to remove. Unplug attachment wires. Replug wires place back in place turn clockwise. Done.
Was this helpful?
Thank you for voting!
Gas was escaping from underneath the burner head
3 of 3 people found this instruction helpful.
  • Edward from ALEXANDRIA, VA
  • Easy
  • 30 - 60 mins
  • Pliers
The old burner head had corroded allowing gas to come out at the bottom. The actual replacement is just turning the head, lifting it out, transferring two wires with slip-on connectors from the old burner to the new one, and dropping the new one in place. Most of the time was spent sanding away corroded metal on the base to make a good fit. The information on the burner head says that the company has decided not to use a gasket under the head. I suggest that was a bad decision.
Was this helpful?
Thank you for voting!
freezer compartment worked fine but very little cooling going to refrigerator section.
3 of 3 people found this instruction helpful.
  • Lee from OZARK, AR
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Freezer worked great but no cooling to refrigerator section. Replaced with part ordered. Phillips head screw driver is all that is needed. Very easy to replace, it's plug and play. New part powered up neither the freezer nor the refrigerator. Went back to old part and atleast freezer still works. New part was no good from factory. The re placement part# matched the original. I attempted to contact PartsSelect but there was no response back.
Was this helpful?
Thank you for voting!
OVEN WOULD NOT HEAT
3 of 3 people found this instruction helpful.
  • Mary from MEADVILLE, PA
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
TOOK OVEN BOTTOM APART AND LOSSENED OLD IGNITERTHEN WENT TO BACK OF OVEN TOOK BACK OFF DISCONETED OLD IGNITER PULLED THE NEW THUR AND CONNECTED PUT BACK ON THEN ATTACHED FROM THE FRONT PUT OVEN BACK TOGATHER THEN TURNED OVEN ON IT WORKED I DID IT MYSELF I AM 64 YEAR OLD WOMEN
Was this helpful?
Thank you for voting!
Oven taking to long to preheat.
3 of 4 people found this instruction helpful.
  • Isaac from LATHRUP VLG, MI
  • Very Easy
  • 30 - 60 mins
  • Screw drivers
Accessed igniter removed 2screws holding it.unpluged igniter installed new one.
Was this helpful?
Thank you for voting!
I craked the gas line fedding the right frount burnner.
3 of 4 people found this instruction helpful.
  • Kareem from Washington, NC
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Wrench (Adjustable)
I removed all four burners and the ignighter wires. then I removed all the screws holding the burnner yokes to the top of the stove. removed the top of the stove and replaced the new fetting. Replaced everything and fired it up. All went well.
Most impressed with the PartSlect web site. the ease of navigaation and the blow up that in abled me to find the part and part number. Ordering was easy and delevery was quick
Thank You.
Kareem.
Was this helpful?
Thank you for voting!
Oven burner would periodically go out and re-light
3 of 4 people found this instruction helpful.
  • Richard from Merrimac, MA
  • Easy
  • 15 - 30 mins
  • Screw drivers, Wrench set
The ignitor is held on by two screws which were rusted in place. When I tried to remove them, the screws became stripped and had to be cut off.

Once the part was free, the rest of the repair went quickly . At that point:
- Pull the element leads enough to get to the plastic connector
- Disconnect the old part
- Connect the new part
- Re-attach to the bracket with new screws.
Was this helpful?
Thank you for voting!
old burner that didn't light and was burning poorly
4 of 7 people found this instruction helpful.
  • John from Ridgefield Park, NJ
  • Really Easy
  • Less than 15 mins
  • Pliers
I used a pipe wrench to turn the old burner off and removed the crumbling washer underneath- no need to replace this. I took off the 2 wires, crimped them onto the new burner, twisted it back into place and presto- all fixed!
Was this helpful?
Thank you for voting!
We live near the pacific ocean - the air is "caustic" from the salt. The burner was rusting out. and the flame was uneven.
3 of 4 people found this instruction helpful.
  • Dimitri from Cambria, CA
  • Really Easy
  • Less than 15 mins
The repair was a no brainer - twist to release the old burner - disconnect the spark wires. connect the spark wires on the new unit - drop it in and twist to lock - about 2 minute job
Was this helpful?
Thank you for voting!
floor panel heavily stained and warped
3 of 5 people found this instruction helpful.
  • Joel from Monroe, NY
  • Really Easy
  • Less than 15 mins
slide latches in rear of floor panel forward and remove.
Was this helpful?
Thank you for voting!
Oven would not ignite
2 of 2 people found this instruction helpful.
  • Dominick from CLARKS SUMMIT, PA
  • Very Easy
  • Less than 15 mins
  • Screw drivers, Wrench set
Very easy, video helped tremendously
Was this helpful?
Thank you for voting!
The oven igniter came on but the gas valve never turned on.
2 of 2 people found this instruction helpful.
  • James from PEORIA, IL
  • Very Easy
  • Less than 15 mins
  • Screw drivers
1. remove oven door 2. remove racks and oven floor 3. remove oven burner 4. unhook igniter 5. install new igniter 6. tuck wiring back in as reinstalling burner 7. put in the insulation supplied in kit 8. install floor and racks. 9. install door. 10. test system 11. oven came on. SUCCESS
Was this helpful?
Thank you for voting!
lights blown out
6 of 14 people found this instruction helpful.
  • Gerald from WINTERVILLE, GA
  • Very Easy
  • Less than 15 mins
replaced lights in refrigirator and freezer
Was this helpful?
Thank you for voting!
All Instructions for the 3127
76 - 90 of 428