EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3127 - Instructions

All Instructions for the 3127
46 - 60 of 428

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Stopped running. Turned to be a bent intake push rod and broken rocker arm
9 of 15 people found this instruction helpful.
  • Rene from COVINGTON, LA
  • Really Easy
  • 1- 2 hours
  • Nutdriver, Socket set, Wrench set
Removed head. Replaced both rocker arms, intake pus rod, push rod guide exhaust and head gaskets. Torqued head in 3 stages to 216 in/lbs. gapped intake to .004 and exhaust to .006 at TDC

Added oil and gas. Now running great

If you need to replace push rods use steel (exhaust) they are the same length
The engine was a Briggs & Stratton 217802 0113 E10604 (2006 year date code)
I used the following
796189 gasket
272475S gasket
697494 push rod
690822 push rod guide
691751 rocker arms
Was this helpful?
Thank you for voting!
Frige evaporator fan became noisy then quit working & frige compartment became warm
6 of 6 people found this instruction helpful.
  • Scott from Bonney Lake, WA
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Came home one evening and found the refer compartment evaporator fan making a noisy/grinding noise. While waiting for the part to arrive the motor finally quit working and the frige lost its ability to cool, but the freezer still worked fine. This is the fan that is inside the frige between the refer & freezer compartments - NOT the fan m otor that is located in the bottom/rear next to the compressor. This grinding noise sounded like it was coming from inside the frige and could be easily heard under the vegetable trays and above the freezer compartment. To access this motor you need to go after it from inside the bottom of the frige compartment - there's NO need to remove the refer door. Pull the vegetable trays and remove the small phillips head screw located down in the lower air flow groove toward the front of the refer. Next, pry up & out the front white trim piece that runs the width of the frige. Once that piece is removed you can lift & slide back the whole lower frige trim/tray. Now lift out the large foam block compartment and you'll have complete access to the evaporator fan motor and the evap coils. Simply pull the fan motor assy out, still attached to the triangular bracket and disconnect the electrical pigtail. Next, pull the fan blade straight off the front hub, split & disassemble the motor bracket, & replace both fan motor grommets. Reverse the steps to reassemble the fan motor to the bracket and reinstall back in the bottom of the frige and plug in the electrical pigtail - the fan should (quietly) fire off instantly and begin the cooilng process. Reinstall the foam block, lower frige tray, front trim piece, reattach the phillips screw, close the door, and give it some time - it took our frige overnight to completely cool down. This is not a tough job, I spent more time figuring out how to access the motor then the actuall replacement. Hope these steps help to speed up your repair! And remeber Red Sox 4 Life!
Was this helpful?
Thank you for voting!
spark ignition in stove failed to turn on burnes.
7 of 10 people found this instruction helpful.
  • David from Upland, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers
Remove burnes and top oven glass, , identified cables for each burner. Unpluged cables, remove old ignition module, drill a hole to install new module. Place module in location. I had to figure out what cables were for the right burner as after placing in the same location as old ignition Module it turned out that they were not identical. I did have to cut old plugs to be able to install cables to new ignition module. If the new part came with and adapter to old cables, as old plugs have small connectors, the new one comes with larger plugs. That would have made it esier.
Was this helpful?
Thank you for voting!
Igniters were flaky on 2 burners and almost dead on 2
7 of 10 people found this instruction helpful.
  • Matt from Craig, CO
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
The part didn't come with installation instructions specific to any stove/oven so I went by a previous testimony on this website and pulled out the stove, and started to remove the side panel to get access. Well turns out I could have done the whole repair in place because on my Maytag the igniter source is accessible by removing the uti lity drawer and it's mounted on a small galvanized steel panel at the left side which hides the part directly. The existing spade connectors were the right size for me but I did have to crimp them tighter (which was perhaps part of the initial problem). After installation, the spark is much more powerful and all burners lit first couple "clicks".
Was this helpful?
Thank you for voting!
Burners would not ignite
6 of 7 people found this instruction helpful.
  • Charles from Kalamazoo, MI
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Removed cover from igniter, took off wires, replaced wires on new one, secured in place, put cover back on.
Was this helpful?
Thank you for voting!
Burners would not ignite flame...Had to start with match.
6 of 7 people found this instruction helpful.
  • Richard from Los Angeles, CA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Wrench (Adjustable)
Removed the old burners with a Plumbing Pipe Wrench by turning 1/4 turn counter clockwise. Disconnected (2) wires and replaced with new Sealed Burners. The simmer burner wires were slightly diffrent from the original but they do fit by opening the connector with screwdriver and then clamping once wire inserted.
Was this helpful?
Thank you for voting!
Faulty bulb receptacle
10 of 20 people found this instruction helpful.
  • Kenneth from Lynchburg, VA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Unplugged the stove and removed the back panel, disconnected the wires from the old receptacle, removed it, inserted the new receptacle, connected the wires, put the back panel of the stove on, plugged in the stove and then checked to see if the bulb was now burning. Success!
Was this helpful?
Thank you for voting!
Electronic spark ignition would not ignite intermittently.
5 of 5 people found this instruction helpful.
  • Charles from Old Bridge, NJ
  • Easy
  • 15 - 30 mins
  • Screw drivers
The spark moule was accessed by removing the bottom storage draw and removing the 2 phillips screws that held the spark module bracket to the frame of the stove located on the rear right side of the draw opening. The new module did come with new spade connectors that reqires cutting the existing connectors off and splicing and crimping th e new connectors to the wires for each of the four burners depending on the model stove. Also I had to use zip ties to secure the new module to the original mounting hardware since the replacement module is not a direct fit. Each of the four burners now instantaneoulsly ignite when turned on. I will buy from Partselect.com in the future. Thank you.
Was this helpful?
Thank you for voting!
the lines were broken
7 of 11 people found this instruction helpful.
  • RONALD from DELAVAN, WI
  • A Bit Difficult
  • 15 - 30 mins
  • Screw drivers, Wrench (Adjustable)
1) removed 2 lines 2) removed 4 screws 3)pulled out old element4) relaced new part 5)installed screws 6) install lines &tighten
Was this helpful?
Thank you for voting!
Refrigerator to warm
5 of 5 people found this instruction helpful.
  • Lloyd from PITTSBURG, CA
  • Easy
  • 15 - 30 mins
  • Screw drivers
Instructions say run capacitor is by motor, but on this frige its in the refrigerator compartment. The capacitors looks different, one square and the other long
Was this helpful?
Thank you for voting!
One element of number display did not light
7 of 11 people found this instruction helpful.
  • Lawrence J from BENTON, AR
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
clock is in top of double oven. Dis-assembly and access to the clock was a puzzle. Four screws in the top of the oven were the solution. The clock panel then folded out and access to three plug-ins and four screws allowed access to the clock. remounted the clock with four screws and replaced plugs. (watch carefully order of wiring) Re-p ower on the oven and set clock. NOTE: Cover said Magic Chef but Label said MayTag
Was this helpful?
Thank you for voting!
Bad Door Gasket.
6 of 8 people found this instruction helpful.
  • Donald from Schuylkill Haven, PA
  • Really Easy
  • Less than 15 mins
  • Pliers
First I took the new gasket out of the plastic bag to make sure it was the right size. Then I proceded to take the old gasket out by pulling it with a long noise pliers. Then I took the new gasket and went around the door putting the pins in the holes that, the old gasket was in. That,s about it.
Was this helpful?
Thank you for voting!
light bulb in water ice freezer door went bad
8 of 14 people found this instruction helpful.
  • Carl from RIVERSIDE, CA
  • Very Difficult
  • More than 2 hours
  • Screw drivers
I didn't. Don't know how to get to light bulb to change it for this specific model
Was this helpful?
Thank you for voting!
Noisy refrigerator
6 of 8 people found this instruction helpful.
  • Eric from NEW YORK, NY
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Screw drivers
I visually inspected the compressor and narrowed down the source of the noise to the freezer area. Then I removed the doors and the screws securing the divider panel. Next I removed the bottom panel of the freezer, the styrofoam insullation panel and the evaporator motor. The motor is mounted between two grommets. I replaced the gromme t facing the fan blades. The aluminum reflector below the styrofoam insulation panel had also come loose. I reattached it and reassembled the refrigerator in reverse order. The noise is gone!
Was this helpful?
Thank you for voting!
Stove seal fell apart
5 of 6 people found this instruction helpful.
  • Teresa from Washougal, WA
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Removed old seal parts and had to cut new part to put into space but it went in without difficulty and has sealed the stove door tight again.
Was this helpful?
Thank you for voting!
All Instructions for the 3127
46 - 60 of 428