31203PAA Magic Chef Range - Instructions

Removed oven door (easy it lifted right off) and remove oven bottom (also easy, no tools). removed two screws holding igniter and unplug old igniter from power. Re-attached new igniter and re-assembled oven.

Parts came very quickly from PartSelect. Good service.

Even though the ceramic insulator looked new (white), it had become non-functional, replacement was simple, 2 phillips screws, reassemble and test. Now I will have to order the other 3.

just turn the burners counter clock wise with the help of a jar opener pad. unplug the wire connectors and replace the burners no hassle, no problem. Everything went fine… one thing though, it is not the same color as it was before. I didn’t realize it until opening the box. Previous color was grey. My wife is Ok with it, so I won’t ... Read more complain, but maybe you should add the color option if there is more than one choice.

Best regards.

First I took the new gasket out of the plastic bag to make sure it was the right size. Then I proceded to take the old gasket out by pulling it with a long noise pliers. Then I took the new gasket and went around the door putting the pins in the holes that, the old gasket was in. That,s about it.

Unplugged the burner heads from the wires, and simply put the wires on the new burner heads and put back onto the stove,. Simple as pie. Very happy that i found parts select online, easy to find the part though your pictures and easy to order.
Loved being able to do this myself without a middle man. Very satisfied!

Removed old seal parts and had to cut new part to put into space but it went in without difficulty and has sealed the stove door tight again.

first I removed the 6 screws that hold the oven in place in the oak cabinet. I slid a kitchen chair in place in front of the oven,then I slid the oven out of the cabinet cut out. Although the gas flex was still connected, I unpluged the electrical connection. I removed the old igniter, unpluged the igniter harness in the rear compartment. ... Read more Then I installed the igniter in reverse.When the oven was pushed back in and secured with the 6 screws,I turned on and tested. Igniter glowed orange and the flame came on. Job was complete in 20 minutes.

I thought that the initial problem based on the users manual may had been the thermostat.
Removal of the old unit and installation of the new one was quite simple.
The only time lag was cleaning some of the surrounding areas of the oven as worked progressed.
As it turned out though, the problem wasn't the thermostat, but ra ... Read more ther the igniter.
But, that was a fairly easy job as well!

I would have never guessed that the problem would have been with the igniter since it was glowing. After reading some of the entries in your trouble shooting area it was clear that this is common and that it likely was the igniter so I simply took off the two screws that hold it in place, inplugged the old, plugged in the new, secured wi ... Read more th the screws and it worked. The only problem I encountered was that when I unplugged the old igniter the plug fell down into the bowels of the oven and I had to fish out with a twisted up hanger.

The flame holder twists about 1/2 inch to left and lifts off. I removed the two screws that holds the igniter on and removed it and installed the new igniter.
There was one complication: when I put it back together, there was no spark. I removed the ground wire and cleaned and scraped it and replaced it and still no spark. But, for n ... Read more o apparent reason the spark returned and has been okay since.

Took the old levelling leg out and screw the new one in.

Turned burner about a quarter of a turn, lifted, disconnected wires, connected them to a new burner and replaced it.

installation was very simple and took less than 5 minutes. first unscrew the burner cap and then remove the 2 wires. to replace reconnect the 2 wires to the new cap and twist cap into place-simple.

I used the other good burner assembly to isolate the problem to the igniters or the igniter block. I ordered both parts from Parts Select. They shipped the parts promptly and after 10 minutes of install time, the burners worked flawlessly.
Thank You Parts Select.

ordered wrong part, called, was sent return number, sent part back, account credited ... easy return policy ... friendly people, good job