31203PAA Magic Chef Range - Instructions

Removed (4) screws that hold the orfice assemblies in place. Removed the 4 nuts from the gas feed tubes. Placed the two new orfices in place and attached the nuts. Replaced range top and replaced the (4) screws into the orfice assemblies. Done. Worked fine the first time.

Take a few screws off the back of the slide in burner module. Take off the back. Unscrew the ignitor screw, remove ignitor carefully, replace with the new ignitor, put the screw back in, put the back back on, try it out! Ours worked after a couple of tries - don't know if the ignitor had to "rev up" by several sparks or we just didn't ... Read more have it properly installed at first. Anyway, very easy. Did it in my pajamas on a Saturday morning.

Range is 20+ year old 'condo issue' and difficult to pull from wall since previous owner had tiled it in. Going in from the back was going to be a pain.
Removed the oven door by opening slightly and pulling up. Removed grilles. Removed bottom of oven by sliding 2 latches in the back forward and pulling it up. Removed 2 screws hol ... Read more ding igniter (long-style) to the rear of the burner. Cut power to the range and snipped the 2 igniter wires as close to the igniter as possible, leaving me only about 1 inch of wire to work with. Removed 2 screws holding old plate to rear of the back of the interior of the oven. Snipped off the connector on the new igniter. Carefully stripped about 3/8" of insulation off of all wires and used hemostat to hold wires together while applying the wire nuts. Used hemostat to work the wire nuts and excess wire back into the hole. Stuffed the hole with supplied insulation. Attached new back plate with original screws and attached igniter to burner with original screws. Reapplied power to range and did a test light. It worked, so I reassembled the rest. For me, the worst part was holding the wires together so the wire nuts would 'take', while working inside of the oven. But, an easy and successful job!

Just used a car oil filter band type wrench and rotated the sealed burner cap a 1/4 turn. cleaned up the rust and dirty. Replaced it with the new cap and tightened it with a 1/4 turn by hand. Instruction can be found on Maytag gas installation manual. The burners are working well and just like a new range.

Replaced spark module but same problem persisted. Realized that the insulation on the spark ignitors were all cracked, causing a short.

Lesson learned: check the condition of the spark ignitors first as these have a tendency to crack. Even the smallest crack will cause a short.

Ordered new spark ignitors and plan t ... Read more o complete repair.

I had to unscrew 4 screws on the burner unit and then 2 screws on each igniter. slip the olds out and the new ones in and then replace all the screws. And wa la they sparked and I was cooking again.

I took off the stove burner and seal (turn counterclockwise by hand.) Then detached the yellow and orange wires by hand. Using a screwdriver, I unscrewed the cover. Then used a 1/2" wrench to unscrew the broken orifice and attach the new orifice.

removed racks, bottom plate. removed screws with a little bit of help from cooking spray. Unclipped old ignitor clipped in new ignitor, used old screws, and inserted insulation replaced racks, bottom shelf. Turn on oven and worked, been using it for about a week now. PS. ordered on monday morning arrived wednesday afternoon.

I took the oven bottom out and then removed the screws that cover the safety valve, then I pulled the oven out and undid the safety valve in the rear of the oven. This was all accomplished with the electricity off and the propane also turned off. I then reinstalled the safety valve.

It was very simple, pull off the old one, then I took some pliers and pulled out the fasteners. Took new gasket from bag and it just snapped into place.

First I unpuged the Range. Then I removed all racks and bottom tray of oven.
The Ignitor is located at back of oven, paralelle to the gas bar. I removed the 2 screws holding the ignitor and unpluged the wires. Then I put on the new ignitor, perfect fit, replaced the 2 screws and pluged in the wires , then pluged in the range. I tur ... Read more ned the oven on and it lit in about 10 seconds.
Thank you PartSelect for having such a wide range of range & oven parts . no one should have to pay a service tech. to fix most problems, as long as we have a GREAT SITE LIKE THIS ONE.
p.s. You guy also had one of the lowest prices , my part arrived ahead of schedule .
THANKS A LOT !

Lifted the top up, only a few inches as the possibality of kinking the gas line was a issue. Took two screws out and replaced the unit, threaded the thermostat down through the oven. It was a breeze. I am 68 year old woman and did I myself.
Most importantly, the process of getting the part was amazing, ordered it in the AM and receiv ... Read more ed it the next day (no extra charge)and by miday the range was good as new. Great service!

My husband did it. I was not there to see it. He said it took less than one minute, just snapped in and worked beautifully.

It was so easy, I pushed the panel towards the back and lifted the front up then lifted it right out. I am so glad that you had the part. I ordered it and when it got here, I just sliped it right in, perfect fit! Thank you so much! Cindy Brison

Had to take off burners and lift off top. Then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires and removed old element. Then I did all steps in reverse to install new thermostat.