EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

31203 Magic Chef Range - Instructions

All Instructions for the 31203
121 - 135 of 540

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
oven would take a very long time to warm
2 of 2 people found this instruction helpful.
  • Barry from East Islip, NY
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
took out both racks and under tray at bottom of stove no tools required.
used a nut driver to remove both screws holding ignighter in place ,pulled wires up gentily and remove from standard clip by pushing ends in.
clip new ignighter in place push wires down again and install 2 screws . put all back together and it works like new .
Was this helpful?
Thank you for voting!
Oven does not heat but broiler works
3 of 5 people found this instruction helpful.
  • Francis from delavan, WI
  • Easy
  • 15 - 30 mins
  • Screw drivers
Oven and broiler have two seperate igniters. Broiler worked but oven did not heat. Oven igniter located under metal pan at base of inside of oven. remove pan by lifting, and remove completely from oven. Igniter under this pan and held in place by two srews. Remove screws, unplug from cable, replug in ne igniter, replace two srcews and pan , and you're done! this part cost about $50 and I installed, last time Sear replaced =$300.
Was this helpful?
Thank you for voting!
oven would not light
2 of 2 people found this instruction helpful.
  • gary from covington, LA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
New parts matched up perfectly. Undid screws holding old igniter, hardest part of procedure because one screw was frozen and broke off. Pulled stove out and new igniter"s connector was identical. Pushed stove back into place and it lighted on the first try.
Was this helpful?
Thank you for voting!
Oven would preheat but would not maintain temperature or sometimes would not preheat. Was temperamental
2 of 2 people found this instruction helpful.
  • Allison from MAYNARD, MA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
1. Remove the oven door by opening a few inches and lifting straight up. Remove racks to access it. 2. The old igniter is just held in by two nuts that have a screw head in the middle of them so they could be removed by a nut driver or by a screwdriver. Unfortunately, both of our screws threads were terribly stripped and after first tr ying to use pliers to help remove them, we ended up using a dremel tool to cut them off. 3. unplug the old igniter and take it out. 4. Plug in the new igniter. 5. attach the two screws. (our time on the repair was mostly spent trying to find two screws around our house that would replace the two that were stripped--otherwise this would have been 15 minutes). 6. return the door and racks by the sliding the door downwards onto the hinges
Was this helpful?
Thank you for voting!
gas burners would not light with electric ignighters
3 of 5 people found this instruction helpful.
  • Leo from Temple, TX
  • Easy
  • 30 - 60 mins
  • Screw drivers, Wrench (Adjustable)
using the diagram shown on line Looked up the ignition module and ordered it by phone. Received it the next day and installed it within the hour. Previously I had called the repairman and he said it would be a couple of weeks before he could look at it and a service call was $75 plus parts..I fixed it for the cost of the module $34. I am very satisfied.
Was this helpful?
Thank you for voting!
Oven would not maintain set temperature.
2 of 2 people found this instruction helpful.
  • Charles from Hardy, AR
  • Easy
  • 30 - 60 mins
  • Screw drivers, Wrench (Adjustable)
1. Closed gas valve at stove supply outlet.
2. Unplugged stove electrical connection
3. Unplugged electrical connections to defective valve
4. Removed 4 screws on burner side of heat heat shield
5. Disconnected gas inlet to defective valve
6. Removed 2 screws holding valve retainer to bottom of unit
7. Lifted gas burner inlet tube while pushing valve toward rear of unit - - - (a bit tricky)
8. Removed valve from rear by tilting forward so valve outlet clear the burner inlet tube and heat shield. Heat shield is not removed, but must be raised enough to allow passage of the valve outlet protrusion.
9. Installed new valve by repeating the preceding steps in reverse.
10. Reconnected gas and electrical, and checked performance
Was this helpful?
Thank you for voting!
replace igniters
2 of 2 people found this instruction helpful.
  • David from CHESTER, CA
  • Easy
  • 30 - 60 mins
Watched u tube video as supplied and followed instructions. Had trouble getting burners off so cleaned around edge of burners with fine bladed knife as suggested by other forum user and used oil filter type wrench to remove burner. There are three bumps on burner that hold it in place so need to turn anti clockwise to remove.
Was this helpful?
Thank you for voting!
igniter glowed but oven would not light
2 of 3 people found this instruction helpful.
  • edward from euclid, OH
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Screw drivers
It looked like an easy fix. the igniter had a plastic clip. A simple R&R. Removed old igniter from its mount, removed plate to get access to wires, removed insulation. Tried to pull the old wires out of its location. It was hung up and I spent 1/2 hr. trying to free it. No go. I thought I'd have to remove oven from its cabinet. I removed six screws and it would not come forward. I felt the under side of the oven thru lower door of cabinet and found out that was where gas was connected. No way was I disconnecting the gas. Pushed oven back in, reinstalled screws and decided to cut old wires and splice in the new igniter. WENT BACK AND READ THE INSTRUCTIONS! Supplied were 4 ceramic wire nuts. Then the light bulb went on! OKAY! I got a marker and marked the top wire on the old igniter to identify it after I cut the wires as close to the back of the old igniter as I could with a pair of side cutters. I then cut the wires as close as I could to the plastic clip on the new igniter. Striped off 3/8 in. from all wire ends and spliced the wires together using the wire nuts. I stuffed the wires as far as possible back into the hole they came from, replaced all old and some new insulation into the hole. The supplied cover would not work, screw holes would not line up and would have fit poorly. I reused the old hole cover. Screwed new igniter to its mount. Turned on the oven and thought I screwed up. I waited about 30 seconds before I saw it start to glow. WHEW! I got it right! After a few more seconds, the gas came on and the oven burner ignited. The really hard part was putting the oven door back on its mount. That door was heavy and wouldn't line up on the first try.......
Maybe if I read the instructions thoroughly the first time before I started, I could have cut my time in half and saved a lot of cussin'. CUTTING THE WIRES WAS AN "OPTION"! That's why they supplied the ceramic wire nuts!....... Dinner is in the oven right now. Smells good!
Was this helpful?
Thank you for voting!
oven would not turn on
2 of 3 people found this instruction helpful.
  • Robert from Clymer, NY
  • Easy
  • 15 - 30 mins
  • Screw drivers
I first removed oven racks.then I removed bottom of oven by sliding locks,then lifting out bottom.Next I removed screw holding e. control cove,then removed cover.Igniter plug was exposed,I then unpluged egniter. I next removed 2 screws holding burner and igniter .I removed igniter and burner as a unit. removed 1 screw from igniter,and rep laced igniter on burner.Then assembled every thing in reverse order,and tested Oven worked perfectly.
Was this helpful?
Thank you for voting!
Faulty oven igniter
2 of 3 people found this instruction helpful.
  • joseph from CLARKS SUMMIT, PA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers
Removed door and bottom oven pan to expose igniter. It was held in place by two sheet metal screws. Tried to back them out but due to heat damage , they stripped. I used my versa tool with a metal blade to cut the screws. I removed the old igniter and disconnected the plug, after I guided it out from the insulation. I installed the new ig niter with two new self tapping screws after I connected the plug and guided it back through the insulation. Reinstalled the oven pan and door. I set the oven to 350° and the new igniter worked. Wife is happy and I saved the repairman fees.
Was this helpful?
Thank you for voting!
Oven would not maintain temperature
2 of 3 people found this instruction helpful.
  • David from Fresno, CA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
First I removed the oven racks, then the bottom cover over the burner. I then unscrewed the two screws holding the igniter on to the bracket on the burner tube. I then removed the storage drawer and loosened the two screws holding the metal shield in place. I then unclipped the electrical connection to the ignitor and pushed it up past the insulation. I then went back into the oven and pulled the wires and connector through. The old igniter was out!

Installation of the new one was just as easy. Screwed the new igniter onto the backet, stuck the electrical connector through the hole in the back of the burner tube, and connected it. I then replaced the shield and the storage drawer, replaced the bottom pan over the burner tube and the racks. The stove works perfectly and my wife is happy. The job couldn't be easier.
Was this helpful?
Thank you for voting!
Range burner drip pans were rusted and old
3 of 6 people found this instruction helpful.
  • Billye from San Antonio, TX
  • Really Easy
  • 15 - 30 mins
The repair was super simple, just remove the drip pan and place new one.
The hard part was finding the drip pan for such an old model appliance. I had shopped locally here in San Antonio with no luck.
I was very happy to find them (exact match) at Part Select and the price was very reasonable. I'll use Part select in the fu ture for needed parts.
Was this helpful?
Thank you for voting!
No spark at any of the 4 stovetop burners.
2 of 3 people found this instruction helpful.
  • Ronald from Berkeley, CA
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
UNPLUG THE POWER CORD! This particular model is a (slide-in) unit, it was wedged between to fixed cupboards/cabinets. Therefore, there are really no side panels to speak of, this made the repair slightly easier. I simply slid the unit out enough to unplug the power cord and access the right side of the uni t. All one needs, at this point, is a Phillips head screw driver to remove a small metal panel installed just below the stove top panel (right side of range), its held with approx. 8 screws. There is one other panel that must be removed as well, (you may want to remove this panel first). It is an enameled-like panel approx. 5" wide x 36" long located at the front of the range (right side) running the length/height of the range (held with 2 screws). Get those 2 panels removed and you will see the spark module attached near center of range just under stove-top panel. Module is attached to a small metal bracket, module has 6 wires attached to it (2 feeding the module and 4 exiting the module to the burners). Bracket screws are nearly impossible to get at (you need a very stubby Phillips screw driver, if you can even get your hand in there). Anyway, I simply released the module from the bracket, then carefully bent the bracket back toward me; to provide work area for my hands. The bracket bends easily and really can't be broken. Now, at this point (using longer needle-nose pliers) detach the wires from the old module (remembering each wires location) or, as I did, hold the replacement module near the existing module and transfer the wires one at a time. Now, slap it all back together as you took it apart. Really simple job, total time is easily/generally under 30 minutes. It may be easier to access the module by removing all the burner components and raising the stove-top? Not sure? I chose not to do the repair that way. Hard part was locating where the manufacturer hid the module on the range. :- ) D.I.Y.ers Rock!!!
Was this helpful?
Thank you for voting!
corroded burners
2 of 3 people found this instruction helpful.
  • Daniel from Can Francisco, CA
  • Really Easy
  • Less than 15 mins
  • Wrench (Adjustable)
Unscrew the burners an install new ones! Anyone could do this.
Was this helpful?
Thank you for voting!
Bad Gasket
2 of 3 people found this instruction helpful.
  • javier from Santa Ana, CA
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
I just twist the burner, pulled it out, disconect the two wires. Reconect the wires to the new burner and placed back .
Was this helpful?
Thank you for voting!
All Instructions for the 31203
121 - 135 of 540