31-65 Tappan Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Burner would cutoff intermittently
1 person
found this instruction helpful.
-
Joseph from FREDERICKSBRG, VA
- Very Easy
- Less than 15 mins
Pulled out old burner/inserted new
Was this helpful?
Thank you for voting!
guide was broken
1 person
found this instruction helpful.
-
Marvin from MONTANA CITY, MT
- Very Easy
- Less than 15 mins
-
Screw drivers
Used a slot screwdriver to pry the old guide...clipped the new guide into its place.
Was this helpful?
Thank you for voting!
Old drip pans had turned to rusty lace.
1 person
found this instruction helpful.
-
Helen from PAWLEYS ISL, SC
- Very Easy
- Less than 15 mins
Unplugged elements. Removed old pans. Wiped out holes. Inserted new pans, replaced elements.
Other Parts Used:
Was this helpful?
Thank you for voting!
Left an appliance on surface element and melted paint onto the element
1 person
found this instruction helpful.
-
Kenneth from LANOKA HARBOR, NJ
- Very Easy
- Less than 15 mins
Plug the new element into the space on stove
Was this helpful?
Thank you for voting!
Drip bowls needed replacing
1 person
found this instruction helpful.
-
Doris from SUN CITY, AZ
- Very Easy
- Less than 15 mins
Removed the old ones and inserted the new ones.
Other Parts Used:
Was this helpful?
Thank you for voting!
Terminal block was bad.
1 person
found this instruction helpful.
-
Chuck from EVANSVILLE, IN
- Very Easy
- Less than 15 mins
-
Screw drivers
Cut the old block off tied new wires to hot wires . That easy!
Was this helpful?
Thank you for voting!
Stem broken off old after market switch
1 person
found this instruction helpful.
-
Gerald from MAITLAND, FL
- Really Easy
- 15 - 30 mins
-
Screw drivers
Pulled control panel off front of unit and replaced switch wire for wire , went great because part sent was OME
Was this helpful?
Thank you for voting!
Broiler element burned out
2 of 4 people
found this instruction helpful.
-
Dominick from Greensburg, PA
- Really Easy
- 30 - 60 mins
-
Socket set
I removed the four screws holding the element in place and pulled the element out and disconnected the two wire. Installation was pretty much the reverse of the removal except, when I went to put the two screws holding the element to the top of the oven I discovered the holes were rusted out. I looked for inserts to put in the holes bu
... Read more
t every time I tried different inserts the holes got bigger. I finally realized the oven is just sheet metal so I moved the bracket about an inch drilled new holes and used self-tapping screws.
Read less
Was this helpful?
Thank you for voting!
wrong part
2 of 4 people
found this instruction helpful.
-
Barbara from WICKENBURG, AZ
- Very Difficult
- 30 - 60 mins
my original part arrived and it did not fit. When I called to explain the problem I was told it was the wrong part. The big problem is... Frigidaire calls the receptacle a terminal block kit as well as a terminal block kit which is a totally different part. I tried to explain that to several different folks I spoke to at your company as w
... Read more
ell as Frigidaire but I'm not sure if I got that point across. Take a look at part # 530 393 5058 and part # 530 440 9888 and you will see that they both mention terminal block kit. Hopefully the part I am getting from Frigidaire is an OEM part and will fit.
Read less
Was this helpful?
Thank you for voting!
Can't regulate burners
1 person
found this instruction helpful.
-
Pam from OCKLAWAHA, FL
- Very Difficult
- More than 2 hours
Didn't get repaired because I could not get the right parts to fix it. You would send me a part for the oven. The oven and burner parts are not the same
Was this helpful?
Thank you for voting!
uneven heating
1 person
found this instruction helpful.
-
Dan from CHEWELAH, WA
- Very Difficult
- More than 2 hours
Repair failed because part did not fit. Offset between top of element and contact prongs was too small, so element could not sit flat.
Was this helpful?
Thank you for voting!
replaced terminal block for element
1 person
found this instruction helpful.
-
Donna from UNION, OR
- Really Easy
- 30 - 60 mins
-
Screw drivers
followed the video provided on line which was very helpful..
Was this helpful?
Thank you for voting!
Broiler Element went out
1 person
found this instruction helpful.
-
Robert from KNOXVILLE, TN
- A Bit Difficult
- 30 - 60 mins
Haven’t got to repair it yet. For the part has not arrived yet and I have no way to track it. For I’ve never received a tracking number
Was this helpful?
Thank you for voting!
Burner will not cool down. I have to switch all the way off.
1 of 2 people
found this instruction helpful.
-
Bennie from Kite, GA
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
First unplug the electricity from the stove. Replacement terminals on back of switch are set different than the originals. So, I took notes (purple wire =P, Black wire=L1, two yellow wires = H1 & H2, and orange wire=L2). Your stove might be different in the color coding. Just take notes. First I unscrewed the screws on the top back plate
... Read more
of the stove. Removed the back plate. Took notes on where the wires went. Removed the wires going to the five terminals. Unscrewed the two screws on front panel of the stove holding the old switch in place. Removed the old switch. Put in the new switch through the back of stove. Determined the length of the control shaft. Take the switch back out. With two pliers on the control shaft, holding the pliers closer to the switch firmly, use the second pliers just past the predetermined breaking point. With the second pliers snap off the control shaft. Be careful not to snap off two much. Place the switch in the proper place and mount to the stove. You may need some parts in the assembly parts package for this. I did not. Inside of the parts package is a set of plastic parts. I selected the part I needed to insert into the control knob for a bushing just to take up space. I placed that part inside of the control knob. I then placed it onto the control shaft. Plug back the wire going to the electric outlet. Instead of unplugging and plugging, you might want to switch off the circuit breaker and switch back on when the job is done. It works!
Read less
Was this helpful?
Thank you for voting!
Heating coils stop heating
1 of 2 people
found this instruction helpful.
-
Sharon from TEMPLE, GA
- Very Easy
- 15 - 30 mins
-
Screw drivers
Remove heating coils raise stove top unsrew terminal blocks cut wires assemble terminals strip wires twist wires together install wire nuts apply heat shrink lower stove top plug in stove repair complete.Thanks.
Was this helpful?
Thank you for voting!