EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

31-397 Tappan Range - Instructions

All Instructions for the 31-397
91 - 105 of 1008

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
L.F. large burner element either on full hot or off. Would not cycle in and out with element control switch setting.
4 of 4 people found this instruction helpful.
  • Gerald from MADISON HTS, VA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Disconnect power to Range at Electrical Service Panel control box. Remove 240 volt service electrical plug to range. Remove back top panel to expose element control switches. Remove element control switch to L.F. burner by first pulling off the control knob. You may need to use a large flat screw driver to pry behind knob to get it starte d but it should come straight off. There are two screws revealed under knob that need to come off. Then the element control is easily, but carefully, removed out the back. Be careful you do not pull the "Hot Surface Indicator Light" switch off right above the element control switch. If you do, this will break the end off the plastic "Hot Surface Indicator Light" lens. If this happens you can still replace it but you will need to use super glue to make the "Hot Surface Indicator Light" switch stay connected to the clear lens. Install new element control in reverse order before gluing the "Hot Surface Indicator Light" switch as stated above or you will knock it off again. While holding the old element control in your hand with wires still attached, remove one wire at a time (making note of the location code for each wire) from old element control and install on new control. The new element control layout for the wire prongs will be different so you need to make sure you look for the code (like L1, H1, P) located on each prong location and put the same coded wire from old element control location onto new control prong code location. Reinstall new element control (with wires pushed fully onto prongs of new control) into panel with screws removed before. Reinstall knob, reinstall panel cover and reconnect range power plug. Restore power to Range at Electrical Service Panel control box With electric power restored, test element control by turning it on and see if it properly cycles on and off at different settings. If working properly you should be able to hear it click on and off and element heating and going off accordingly.
Was this helpful?
Thank you for voting!
Burners getting too hot.
4 of 4 people found this instruction helpful.
  • Leslie from CONCORD, NC
  • Very Easy
  • 15 - 30 mins
  • Screw drivers, Wrench (Adjustable)
Watch video. This oven had the connecters that popped off and on which made this task easy.
Was this helpful?
Thank you for voting!
Switching out drip pan, surface element and glide door
4 of 5 people found this instruction helpful.
  • Carrie from SEMINOLE, FL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
i used a screwdriver to remove the old drip pans and broken surface element in addition to prepping the bracket for the door. It was extremely difficult for me to find these parts for the frigidaire oven but these fit perfectly! I was extremely pleased with how quick it was to replace or fix everything. I will definitely order again when the other surface elements go!
Was this helpful?
Thank you for voting!
Bottom burner wouldn’t heat
5 of 8 people found this instruction helpful.
  • cynthia from SEBRING, FL
  • Really Easy
  • Less than 15 mins
  • Screw drivers, Wrench (Adjustable)
Watched the video
Was this helpful?
Thank you for voting!
oven baking element burnt into
4 of 5 people found this instruction helpful.
  • Teresa from Marengo, OH
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Socket set
my husband did the repair.He unplugged the stove removed the element and installed the new element.plugged the stove in and checked operation of element.Stove works great
Was this helpful?
Thank you for voting!
The neon tube over the stove top went out
8 of 17 people found this instruction helpful.
  • Gunther from Columbia, SC
  • Really Easy
  • Less than 15 mins
Put a new one in.
Was this helpful?
Thank you for voting!
Coroded drip pans
4 of 5 people found this instruction helpful.
  • Lori from Old Town, FL
  • Really Easy
  • Less than 15 mins
Removed heating elements and replaced drip pans. And by the way, this is the only 'pans' I could find to fit. Thanks.
Was this helpful?
Thank you for voting!
replacing oven racks
4 of 5 people found this instruction helpful.
  • Lawrence from Elmira, NY
  • Really Easy
  • Less than 15 mins
The replacement racks were spot on and the service was outstanding. had the racks in 2 days. Happy Happy Joy Joy! :)
Was this helpful?
Thank you for voting!
Old racks had melted plastic on them.
4 of 5 people found this instruction helpful.
  • James from PAINESVILLE, OH
  • Very Easy
  • Less than 15 mins
It was a replace racks not repair. No problem
Was this helpful?
Thank you for voting!
Broken door glide
4 of 5 people found this instruction helpful.
  • Michael from Signal Hill, CA
  • Really Easy
  • Less than 15 mins
snapped the new piece of plastic in its place and ta da, its fixed.
Was this helpful?
Thank you for voting!
Switches were going bad and making a popping sound and smoking.
4 of 5 people found this instruction helpful.
  • Joshua from Homestead, FL
  • Easy
  • 30 - 60 mins
  • Screw drivers
Pulled out the range, unplugged it and removed the upper back panel. The switches were held in place with two screws. Removed the old switches, detached the wires and plugged them into the new switches. Mounted the new switches, replaced the back panel, plugged the range back in and pushed it back into position. Appliance repair compa ny wanted $370. I did it in 45 min. for less than $100.
Was this helpful?
Thank you for voting!
Front left burner would not shut off, then switch fried
5 of 8 people found this instruction helpful.
  • connie from madison, NC
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Unplug range, remove top back panel. Remove knob. Replacement part is different, but if you look closely, each metal tab has a number stamped on the plastic housing directly beneth it. Remove old switch (2 screws)and remove and replace wires one at a time. You will need to cut the "one size fits all" metal shaft that the knob attaches to. We had to remove most of it, leaving only 2 "segments". File rough edges and apply vaseline so that the plastic sleeve will slip right on. We used the shorter sleeve (only 2 that are supplied will fit the knob). Replace unit and screw in. Replace knob.
Was this helpful?
Thank you for voting!
Repaired Oven Range Light Bulb
3 of 3 people found this instruction helpful.
  • Alan from SAN MATEO, CA
  • Very Easy
  • Less than 15 mins
  • Screw drivers
The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.
Was this helpful?
Thank you for voting!
the old bake element was corroded and non-funtional
5 of 9 people found this instruction helpful.
  • Stephen from RONAN, MT
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Using a socket set and Robertson #3 (smallest) driver head,with the breaker shut off before working I removed the old element and disconnected the old element from the wire connections.I then installed the new element by connecting the terminals to the wire connection in the range before screwing the old retaining clips to the back of the oven compartment wall.Then I flipped the breaker switch back on and turned on the oven dial to 425 degrees to see the element heat up and glow red affirming the success of the repair.Total time to repair about 15 minutes.
Was this helpful?
Thank you for voting!
Drawer Glide Was Broken
3 of 3 people found this instruction helpful.
  • Karen from Yuma, AZ
  • Very Easy
  • Less than 15 mins
Took the drawer out, snapped the new glide in place, and replaced the drawer. Installation was simple with no tools required.
Was this helpful?
Thank you for voting!
All Instructions for the 31-397
91 - 105 of 1008