2263 - Parts

This microwave door switch provides power to the various components in the microwave when the door is in a closed position, and interrupts power when the door is open. This door switch is approximately 1 1/2 inches long, and has 2 metal prongs called terminals that extend from its body. If your microwave will not turn or heat properly, th...Read moreere could be an issue with the door switch. You can check the switch for continuity using a multi-meter. With the actuator button depressed, you should see continuity between these terminals. If there is no continuity the switch will need to be replaced. NOTE: Before you begin this repair, first make sure your microwave is unplugged, and that your capacitor is discharged. A capacitor stores large amounts of electricity even when your microwave is unplugged.

This OEM glass cooking tray is a removable glass plate, measuring 13 inches in diameter, that spins inside the microwave during operation. It ensures that heat is evenly distributed in the microwave to properly heat or cook the food. Over time, the heat generated in the microwave can cause the glass to warp and the plastic rollers to wear...Read more down. The glass can also crack or shatter accidentally. It is important to replace the glass as soon as it is no longer functioning well to prevent uneven heating and reduce any safety hazards from damaged glass. Carefully pull the old glass cooking tray from the microwave and clean the microwave cavity. Place the new tray onto the rotating mechanism, and properly align it with the rollers. Turn the microwave on and check to see that the tray is rotating freely.

This micro-switch is designed for use in your microwave. The function of this part is to monitor the door latch position and communicate to the electronic control board whether the latch is open or closed. If your microwave does not provide heat, or will not start properly, you may need to replace the micro-switch. This part is approximat...Read moreely 1 inch in length and 3/4-inch in width. It is made of black plastic with two metal prongs. This is an OEM part sourced directly from the manufacturer. This part is sold individually. Be sure to disconnect the microwave from the power source before you begin this repair.

The fuse-time delay may also be known as a line fuse or a microwave fuse, and it is a piece for your microwave. The function of this part is to shut off the microwave if there is a power surge, in order to protect your microwave from damage. You should consider having a service technician install this part as the high-voltage capacitors i...Read moren a microwave can contain a very harmful electrical charge, even when the microwave is unplugged and has been inactive for some time. The tools that would be needed to complete this installation include a Phillips screwdriver, an insulated screwdriver, and a pair of pliers.

This is a halogen lamp, or light bulb, for a microwave. The microwave light should illuminate the inside of the microwave while the door is open and while the appliance is running. If the light bulb does not illuminate, you may need to replace it. This part is sold individually. It is a common wear part and does not have a standard light ...Read morebulb base, so consider ordering a spare. This part is made of clear glass. If the glass on the existing light bulb is broken, you may need to use a pair of needle nose pliers to remove it. Be sure to handle the broken part with work gloves and disconnect power to the appliance before changing the bulb.

This magnetron in your microwave creates the radiation needed for cooking or warming your food. It is located inside the main cavity, typically near the transformer or waveguide. When the magnetron becomes defective, your food may not heat up properly or heat up at all. Additionally, buzzing or humming sounds may be noticeable while the m...Read moreicrowave is in operation. With a malfunctioning magnetron, your microwave loses its primary function. To remove it, you first need to unplug your microwave from its outlet. Before touching any components, discharge the capacitor by placing a screwdriver, with an insulated handle, across the two terminals of the capacitor. Once the capacitor is discharged, replace the current magnetron by disconnecting it from any wires and removing any mounting screws or clips. This magnetron is sold individually and is supplied directly from the original equipment manufacturer.

This 5/16-18 wing knob is sold individually. It is a plastic part, black in color, that works on a variety of equipment. Its general function is to allow you to quickly loosen, remove, or fold down things such as handles. If it no longer loosens or tightens, it may be broken or damaged due to fatigue and wear. Replacing this part is an easy repair that does not require any tools.

This replacement front wheel and tire assembly is specially produced for Murray lawn mowers. It is a genuine manufacturer sourced item, not an aftermarket imitation. This is the front wheel that supports and helps to move your mower around. This wheel is made out plastic with a rubber tire it is sold individually. Please note, the dust co...Read morever, hubcap and the hardware to secure this wheel are all sold separately. To replace this wheel you would need a wrench. • Remove the hub cap and the locknut • Replace the old wheel with the new one • Secure it with a nut and a hub cap

The Cutting Blade is a black, metal, individually sold blade which is used to cut grass. It attaches underneath the cutting deck under the mandrell shaft. Installation is rated as "Easy" and requires a socket set, and wrench set. If worn or damaged, the grass will not cut properly and the part should be replaced. Refer to your make, model...Read more and diagrams in order to determine if this is the correct part for your machine.