20462 - Instructions

Using a socket set and Robertson #3 (smallest) driver head,with the breaker shut off before working I removed the old element and disconnected the old element from the wire connections.I then installed the new element by connecting the terminals to the wire connection in the range before screwing the old retaining clips to the back of the ... Read more oven compartment wall.Then I flipped the breaker switch back on and turned on the oven dial to 425 degrees to see the element heat up and glow red affirming the success of the repair.Total time to repair about 15 minutes.

The diagram on the frigidaire website said 4 screws and 3 wires to disconnect and part comes out and reverse the steps for install actually took less then 5 mins...easiest and first repair I have done and the part was 20 bucks cheaper at parts select then anywhere else on the internet!

Remove the freezer drawer by unscrewing the two 12mm screws on both sides of the drawer.
Lift the drawer up out of the slots the frame and away.
Lay the drawer on a padded surface to protect the drawer cover finish.
Pull the old gasket out of the drawer and discard.
Position the new gasket around the edge of the drawe ... Read more r. Starting at one corner press the gasket into the slot in the drawer edge. Continue working the gasket until you return to the starting point.
Inspect the gasket to ensure it is seated in the slot completely.
Return the drawer to the refrigerator, placing the lugs on the drawer into the slots of the frame and insert the screws to their original position and tighten securely.
Inspect the drawer for proper level/sealing in the freezer drawer position. Adjust as necessary.

After a brief discussion with CS about the electric stove part was shipped it arrived and I proceeded to install I found it needed to be installed sideways not up & down like the old one. The terminals did not line up so I put the black lead first and the purple lead last in doing that I burned out the switch??? was not easy to install as ... Read more the video showed his switch matched each wire? My installation was sideways??

Removed the wires that I could, then terminal block. Installing the new terminal block was very easy; however the wires that arced were fused to the terminal bock screws and needed to be cut and new connectors had to be put on the wires to allow them to be reattached to the block safely.
Once all was replaced and reinstalled the oven ... Read more has worked great. The length of the repair was increased because of the melted parts and having to run to the store to get the new wire connectors big enough to fit on the wires. If we were simply replacing the block and had not encountered the melted ends, it would have been a very quick and easy repair.

Pulled stove away from wall and unplug .Removed grates for better access. Unscewed element scews removed element & tested for continuity.there was none element is bad . Replaced with new one . Time about 20 minutes.

Used instruction video & replaced part.

Removed the back panel, disconnected the terminals and removed the old one and installed the new one.

Unscrewed the 4 screws that hold the dispenser in place. Disconnected the wiring harness from the old dispenser.

Reconnected the wiring harness to the new dispenser.
screwed in the 4 screws that were removed.

Works like a charm!

Originally I had anticipated a major problem requiring the removal of the back of the range and perhaps the necessity of employing the services of a repairman ($$!). Fortunately I waited for the arrival of the replacement element, which, upon inspection, was not configured to go through to the back of the range. What a relief!

... Read more The hardest part of the repair was finding the correct nutdriver (5/16"). Removal of the damaged element was simply backing out the two retaining screws inside the oven and pulling the element out far enough to expose the clips to the wire. Pulling them apart was easy enough, and then the element I disposed of immediately.

Reverse of removal of the old element was the installation of the new: Reconnect the clips to the element, push the wires back into the insulation, re-inserting the two retaining screws and tightening them gently.

The final step was to plug the range 220 cord into the outlet. Testing whether the element was functional was a breeze; the oven and the range elements worked perfectly.

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.

I pulled the old one out and pushed the new one in place.

Removed 2 screws, pulled out the panel, replaced the new panel and replaced the two screws. Less than 5 minutes.

after getting the correct part all that was needed was to remove several screws for the holding brackets to attach that bracket. also had to remove and place rollers on new part. not very difficult but took a minute to line up screws correctly

This was my first time ever working with electrical issues. My husband is not physically able to do repairs now. Very easy fix. Just viewed video repair instructions and it went exactly as instructed. Within 45 minutes, I had my stove repaired and cleaned and back in working order!! Great results. My range is working perfectly again and M ... Read more ama is happy!!