The Oven Bake Element is a black, metal part which supplies heat to the oven. This element is 19-1/2" wide x 18-1/2" long and has 3-1/2" inserts. It is rated as "Easy" to install by users, and attaches to the bottom of the oven. If you notice visible damage, or that your oven is not receiving heat properly then it may be a problem with th...Read moreis part. Check your model number and user manual to see if this is the right part for you. It is important for you to disconnect your appliance from the power source before performing this repair. After disconnecting your appliance, remove the two screws/nuts connecting the old element, pull it out, and discard if faulty. Simply connect the new element prongs where the old element fit, and screw it back in. You may need a flashlight when making this repair.
This OEM refrigerator filter is for french door and side-by-side door types and is located in the back, top-right of your appliance. By absorbing heavy metals, pharmaceuticals, pesticides, chlorine, and much more, this filter provides delicious and healthy drinking water. This filter measures 2 inches deep, 9 inches high, 2 inches wide, a...Read morend weighs 0.9 lbs. The installation is quick and easy with a push and twist feature. Don't forget to run water through the dispenser for about three minutes or 1.5 gallons to prepare the filter before use. For best performance replace this filter every six months.
The infinite burner switch controls the stove top eight-inch surface burner, which is the large surface element. If your surface element is not warming up, the element can be tested to determine whether or not it is defective. If your element is not defective, then it is more than likely that the infinite burner switch is the issue. Befor...Read moree you install the infinite burner switch you will need to unplug your range from the power supply, or shut off the home circuit breaker. The tools you will need to do this repair include a number one square head screwdriver and a pair of needle nose pliers.
This package contains one carbon activated filter for refrigerators with Pure Air Ultra II filtration systems. The air filter cleans the air and absorbs strong odors from fragrant foods, such as onions, garlic, seafood, and over-ripe fruits and vegetables. By absorbing these unpleasant smells, it will also improve the flavor of your ice c...Read moreubes.
This is a simple repair that does not require tools for installation or removal. Start by removing the plastic wrap on the new filter, remove the cover from the housing inside the refrigerator, remove the old filter, place the new filter into the housing, and close the cover. Depending on the model of your appliance, you may need to reset the filter reminder. This part is OEM official, guaranteeing a smooth install and proper fit.
This genuine OEM oven probe is also known as an oven temperature sensor or range probe. This part is manufactured for a range, stove, or oven to detect the temperature within the oven cavity. The probe allows the oven to maintain the set temperature by sensing the temperature and sending the information to the ovens motherboard. You may n...Read moreeed to replace this part if oven is not heating or is heating unevenly. Be sure to disconnect power to oven before replacing, as it is an electrical part. Tools needed are 1/4 inch nut driver and needle nose pliers.
This OEM 40 watt appliance light bulb is used for some ranges, refrigerators, freezers, and microwaves. Simply locate the existing bulb, unscrew it from its socket, and replace with new light bulb. If the existing bulb is broken in the socket, disconnect the power to the refrigerator and use a pair of needle nose pliers to grip the intern...Read moreal fragments of the bulb to unscrew. Replace with the new bulb and reconnect the power to the refrigerator. These bulbs are sold individually and are a commonly replaced part; consider ordering a spare.
This mullion hinge pin is a genuine OEM replacement part, measuring 1.5 inches by 1.25 inches by 0.85 inches. It is specially designed to secure the mullion in refrigerators, allowing it to pivot and ensure smooth door movement. The mullion acts as a barrier between the refrigerator and freezer to maintain the desired temperatures for eac...Read moreh section. A damaged or loose hinge pin will result in temperature fluctuations, frost buildup along the door edges, and difficulties opening and closing the door. Therefore, it is important that you replace the pin as soon as it is no longer functioning. Note that your appliance may require two hinge pins, one near the top of the mullion and one near the bottom. Remove the mullion cover, detach the hinge pin, and install a the new one into the hinge assembly. Place the cover back on and verify that the hinge assembly is working by carefully opening and closing the refrigerator doors to check that they are moving smoothly. Each sold individually.
This crisper pan roller is sourced directly from the manufacturer for use in your refrigerator. It is a genuine OEM part that is designed to fit just like the original for your convenience. The roller is a plastic wheel-like component that attached to the sides of the crisper pan and allows it slide in and out of the refrigerator smoothly...Read more. The rollers allow users to easily and conveniently access the contents of the drawers. Over time, the roller may wear down, break, or fall off. If the roller is faulty, you may notice difficulty sliding the drawer in and out, or the drawer may feel loose and unstable when you pull it out. Each crisper pan roller is sold individually. Ensure that you order the correct number of rollers for your refrigerator.
This is a part for your range. This switch controls the stovetop surface burner. If you notice that your stove top is not turning on or is not adjusting to the corresponding desired heat, it is mostly likely due to the burner switch needing to be replaced. You will need a #1 square-head screwdriver and needle-nose pliers. Disconnect the p...Read moreower from the range. You will need to move the range out from the wall to remove the upper back panel to access to this part. This is an OEM genuine part.
Terminal block kits are also known as terminal boards, or terminal strips, and they are found in a wide variety of household appliances. Most often in ranges, wall ovens, and dryers. This kit attaches the power cord to the inner wiring of your appliance. If the terminal block is faulty, your appliance will not get the power it needs to op...Read moreerate properly. When removing the old block pay close attention to the wire placement, this will make installing your new part much easier. If you notice any of the wires or wire terminals are corroded or damaged they will also need to be replaced.
This crisper drawer cover assembly is a genuine OEM replacement part designed for select Frigidaire refrigerators and compatible models from Kenmore, White Westinghouse, and Tappan. It includes a durable plastic frame, a glass insert that serves as a shelf, and integrated rail brackets that allow the crisper drawer to slide smoothly. Posi...Read moretioned above the crisper drawers, this cover helps regulate humidity and temperature to extend the freshness of fruits and vegetables. Its dual function as a shelf adds extra storage space while maintaining the organization and efficiency of your refrigerator interior. Installation is straightforward and requires no tools.
This refrigerator ice maker assembly includes the ice mold and integrated control mechanism responsible for freezing water and dispensing ice automatically. Designed for compatibility with select models from Frigidaire, Kenmore, Electrolux, Crosley, and others, it replaces older assemblies and restores reliable ice production. Common symp...Read moretoms indicating the need for replacement include leaking, failure to produce ice, or inconsistent performance. Before installation, disconnect the refrigerator from its power source and verify compatibility using your appliance’s service manual. This assembly offers a dependable solution for restoring full ice-making functionality.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven woudn't heat
1298 of 1510 peoplefound this instruction helpful.
David from Shawnee, KS
Really Easy
Less than 15 mins
Screw drivers
1. Removed two screws, pulled out the element, voltage tested the element and determined it was an open circuit (bad element). 2. Ordered the part from partselect.com 3. Disconnected element, connected the new one, and screwed it back in.
Was this helpful?
Thank you for voting!
Element cracked in two pieces
821 of 928 peoplefound this instruction helpful.
Michael from Green Bay, WI
Really Easy
Less than 15 mins
Nutdriver
Shut off circuit breaker to stove and collected the tool from the basement. Turned on flashlight. Unscrewed the two hex nuts from the old element/back of the oven. Slid the old element prongs out of the back, exposing the connecting wires. Pulled the connecting wires off of the old element, carefully, so that the connections wouldn
... Read more't come off of the wires. Threw the old element pieces in the garbage. Connected the new element to the connecting wires and re-fastened the hex nuts. My husband had wanted to call the repair man, but it didn't look too difficult, so I decided to try it on my own. Boy was he surprised when I fixed it, and for a fraction of the cost of hiring a repairman! Ladies, we can do this ourselves!!! :) Thank you for being there for us to order our part from, Parts Select, we had our new part in less than 24 hours, so the shipping was blazing fast!!! Keep up the good work!!! :)
Read less
Was this helpful?
Thank you for voting!
oven did not heat
438 of 479 peoplefound this instruction helpful.
jack from chambersburg, PA
Really Easy
Less than 15 mins
Screw drivers
removed screws pulled element out. removed wire from old element replaced with new element.very easy