2003 - Parts

This is a Genuine OEM Authorized Gasket used on variety of Lawn and Garden Equipment Engines. This part is made out of Rubber and it is sold individually. If the carburetor is leaking fuel it is recommended to replace the Bowl Gasket. Gaskets and O-rings are a common source of problems. They eventually shrink, causing fuel and air leaks t...Read morehat lead to poor engine performance. When replacing this Gasket you would need a Screwdriver and a set of Wrenches.

Genuine Manufacturer Sourced replacement part used on a variety of Briggs and Stratton Engines. This filter adds a second layer of protection against airborne-dirt particle ingestion. This is a Foam Pre-Cleaner which is Sold Individually. Please note a Paper Filter and a Cover are both Sold Separately.

This authentic OEM starter assembly is designed for use with lawn and garden engines and is sourced directly from the original manufacturer to ensure quality and compatibility. The assembly includes a durable plastic shroud/housing, starter pulley, recoil spring, pull rope with grip, and the necessary hardware for installation. It functio...Read morens as the primary mechanism for manually cranking and starting the engine. To complete the replacement, you’ll need a wrench. Simply remove the four screws and nuts securing the old starter assembly, then install the new one using the included hardware. This item is sold as a complete individual assembly.

This item is an authentic replacement part that has been sourced from the original manufacturer to be used with lawnmower engines from Briggs & Stratton and Toro. The metal float bowl fits onto the bottom of the carburetor and is used to house the float and store and drain the fuel that actuates the needle valve. This item is available as an individual replacement part.

This is a Genuine OEM replacement part used on a variety of Lawn and Garden equipment. The key helps to secure Flywheel in place. This is a Metal Key and it is Sold Individually. You would need Pliers to replace this item.

This screw, also known as a shoulder bolt, is a genuine OEM replacement part for your lawn mower. This metal screw holds the starter grille in place against the rewing starter on your lawn mower. It requires a wrench to be loosened or tightened.

This OEM Locking Ring holds components or assemblies onto a shaft or in a housing/bore when installed in a groove. Installation is rated as "Easy" by customers and will require pliers. The part secures the drive pinion gear to the drive shaft, and if broken due to wear/fatigue/damage, it will need to be replaced.

This is a genuine OEM sourced replacement part. It is designed for use with lawn and garden engines. It is an important part of the starter assembly that is used to crank start the unit. Please note shroud/housing, starter pulley, starter spring, grip, the pull rope and the hardware are all sold separately. This pawl plate is made out of ...Read moreplastic and it is sold individually. To complete this repair you would need a wrench.

The Shoulder Bolt is a 3/8-16 x 3-5/8 bolt, certified by the original equipment manufacturer. It is a metal bolt which is individually sold and comes in black. Installation requires a wrench or socket and is rated as "Easy" by customers. It is mostly used to keep the wheel in place. It fits onto the unit frame and if broken or removed, th...Read moree wheel will fall off. Refer to your make, model and diagram to ensure this is the correct part.

This OEM Oil Seal is an individually sold rubber part which is attached around the axis shaft on the crankcase housing to provide a proper seal. A broken seal will lead to a leak, and the part should be replaced. Installation is rated as "Medium" difficulty by customers, and will require a screwdriver, wrenchset and seal puller. Refer to ...Read moreyour make, model and diagrams to ensure you've chosen the correct part. This model comes in black and grey.

This replacement part is designed for use with Briggs and Stratton engines installed on lawn and garden equipment. It is used to filter out dust and debris from contaminating engine and carburetor. This cartridge will get dirty over time requiring replacement. This is a pleated paper filter with a plastic base/frame. Includes one (1) filt...Read moreer cartridge per order. Please note foam filter is sold separately. Replacing air filter is easy and does not require any tools. • First remove the knob • Remove cover and take out old air filter • Clean out the filter base/housing • Place new air filter in the case • Reassemble and test the engine

This is an Authentic OEM replacement part used on Lawn and Garden Engines. The purpose of this part is to mix air and gas before the fuel mix goes to the engine. If the engine won\'t start and the tank is full of fresh fuel, test the carburetor by removing the air filter and pouring about a teaspoon of fuel into the carburetor. Pull th...Read moree starter rope. If the engine starts and then quickly dies, the carburetor is likely the problem. This Assembly includes a Metal Body Carburetor, Rubber O-Ring and a Gasket. When replacing Carburetor it is advised that you also replace Carburetor Gaskets to ensure proper Air Tight Seal for optimum performance. You will need a Screwdriver to perform this repair.