1960 - Instructions

First i removed the top two screws that help the ice maker in place then remove the bottom screw, then unplug unit from freezer, removed ice maker for freezer, took out wire harnes, put wire harnes in new ice maker, plug new unit in place the unit in freezer and put in the bottom screw, them align the top two screw and but them in and was ... Read more done. Check ice maker in two hours and there was new ice being made.

Removed two screws on top. Then one under the ice maker ,held on to it while I unpluged the white flat plug. Then installed new one in reverse. Of course re-connect power wires on.
I turned power off at fuse box.
First batch of ice in an hour or so.

It was real easy. I unpluged the fridge. Took out the three screws that held the icemaker to the wall. Unpluged the wire harness. Removed the old icemaker and reversed the order to install the new one. Everything lined up perfectly.

I simply removed the 3 screws holding the unit into the freezer with a nutdriver, then disconnected the power plug (a little hard to get to, and requires releasing a small tab in a hole in the main body). The icemaker came right out with no problem. I then had to change out the water funnel inlet because mine had a different style than th ... Read more e one provided on the new one. This was easy also, just remove 2 phillips head screws that are set deep in 2 holes in the face of the motor drive unit, then pull the whole assembly apart far enough to allow the ejector blades to slip out of the hole through the inlet funnel, then snap the funnel loose to move it to the new one (the same technique to be used on the new one, then re-assemble in reverse order).

First, unplug power to Fridge, then remove ice bin and set to one side, then remove the clip that holds the fill tube down by pulling up on it, and remove the fill tube. Remove the two top screws on ice maker assembly first, as the bottom screw will support unit. Then remove the single bottom screw. Rotate the Ice Maker slightly down an ... Read more d this will expose the electrical connector. With a short, small, flat head screwdriver in your left hand, depress the locking tab for the connector, while your right hand supports the assembly and pulls the connector outward to disconnect. Remove old Ice Maker, and remove the bin full lift wire, it's a slide in fit and install in your new unit. Check your fill tube water diverter on the right side of Ice Maker unit , you may need to remove the blank, it is U shaped and molded for easy removal, but use caution when removing to be on the safe side, this allows the fill tube to go down into the diverter, Re-Assemble in reverse order. Give the unit plenty of time to reach proper operating temp, and cycle. Make sure and discard your first Ice cycle.

Piece of cake. Removed two screws, pivoted old ice make up, lifted it out of the mounts. Installing the new one was just the reverse.

Identifying the correct replacement ice make was easy also, due to the photographs on PartsSelect.com

There was three screws to remove to unmout the ice maker, and unplug the wire harness,then two to remove to slip in new stripper. All took about 20 mins.

Barely a couple years old, was not getting any ice. I carefully selected the right part on this website and ordered. Around $150 and was easy install.

1. Mine was upper and lower freezer. you slide the freezer door out and lift it up, it will come right off.
2. pull out the tray above and ice bucket
3. Use a screwdr ... Read more iver to unscrew 2 screws above and one below the existing icemaker
4. unclip the power cable line

Thats it!

Point to note: the new piece you get will not have the power cable line, the water cover and the metal arm. I would think it should have for $150, but keep this as you will need a few little parts to complete the new part before installing it back.

VERY easy to do installation. Dont pay anyone to do this, it can be done easy!

Removed one screw ,unpluged ice maker, and replced it with new one.

First, I removed the ice bucket. Then I removed the two top left screws and bottom screw with a 1/4 inch nutdriver. I pulled the assembly out as far as the wiring harness would allow, disconnected the harness on the lower left side, and removed the unit. I removed the old motor cover and ice stop wire and placed them on the new unit. ... Read more I then reversed the process. It went so fast that the freezer must have still been close to zero degrees because it filled with water within 15 minutes.

very simple,remove old and unplug install new,three screws, used old hose clip.

Turn off water, removed two mounting screws, unplugged solenoid, removed incoming water connection and plastic pipe to ice maker. Installed new valve, connected water lines, reconnected plug, remounted with screws. Turned water back on, over rode power to ice maker and checked for leaks. Total time about 5 minutes. Very easy repair.

I first loosened the hex screws and lifted the unit off. Then I unplugged old unit from the wiring harness. I did have to switch the inlet funnel since the new unit was a little different. I used the one from the old unit. I then plugged it back in, rehung and tightened the screws. The unit started operating within a few hours.

I read the instructions from your site, removed the old unit, salvaged the parts to be reused and reassembled. 1/2 hour later I had ice and no leaks.

First i removed the three screws that held the assembly to the fridge, then removed the water flow tube from ice maker. 2- flipped ice maker over ,then used a small flathead to push in locking tab that held wire harness and out comes ice maker. All though the water cup was not quite the same i used the old ice maker to take apart to ... Read more see how it was put together,hopeing there wasn't a myriad of parts. -NO INSTRUCTIONS- piece of cake, don't take out outside screws,take out the 2 inside screws-these srcews hold the guts to the water tray-pull apart and reassemble the unit after you have switched the cups. then reinstall into fridge with your outside cover and the full bin wire and your done. It helps to be alittle mechanicly inclined. -NO GUTS NO GLORY,DONT BE AFFRAID TO LOOK OUTSIDE THE BOX-