1802 - Parts

The speed nut (also referred to as a condenser motor fan nut), fits onto the condenser fan motor. The motor for this fan turns on simultaneously with the evaporator and the compressor motors, so a malfunction in the condenser fan motor could cause your fridge to cycle on and off more frequently or run too warm, or too noisily. Make sure t...Read morehat the speed nut is properly attached and tight. Check the nut for any signs of wear or damage. If the nut is damaged and refuses to tighten, you should replace the part immediately. Remember to unplug your refrigerator before starting this repair.

This door hinge washer is used between the lower hinge pin and the lower hinge bushing.

This drier may also be known as a refrigerator ultra-violet dye drier or a filter drier and is meant to be used with your fridge. This piece is a filter for the refrigerant that moves through the refrigerators sealed-system. The most common reason you will need to replace the filter is if your fridge/freezer is not starting. You should co...Read morensider having this piece installed by an appliance repair technician that is trained and licensed. Installing this part requires specialized knowledge and tools. The installation will require the service technician to recover and recharge the refrigerant in the refrigerators sealed-system.

Sourced directly from the manufacturer, this part is used to open and release hot water if the water exceeds the maximum operating temperature. It has metal and plastic components, is not part of a kit or assembly, and is sold individually. When malfunctioning, the Thermo Relief Valve will open on a regular basis, which can cause damage ...Read moreto your pump. If it is opening often or on a regular basis, replace it to protect your pump from damage. You will need a socket set, a wrench set, and pliers to complete this repair. Customers rate this repair as Easy.

Sold as a kit including the connector, ball, and spring, this genuine OEM replacement part is used in various models of pressure washers to connect the chemical hose (soap hose) with the pump. It will be found on the pump of your machine and is made of metal. You will know this part is malfunctioning if you do not have soap coming out o...Read moref the nozzle. This part is known to wear over time and should be replaced when you noticed signs of damage or fatigue. You will need a wrench set to complete this repair. Customers rate this repair as Easy.

Designed for use in various models of pressure washers, air compressors, and generators, this Woodruff Key is used to hold a shaft with a mating part, such as a gear. It is 1 inch in length, made of metal, is silver, and is sold individually. If the mating shaft or gear no longer rotates together, you likely need to replace the Woodruff...Read more Key. Inspect it for signs of fatigue or wear, which occurs through regular use, and replace it if needed. You will need a wrench set, an allen key set, a screwdriver, and pliers to complete this repair. Customers rate this repair as Easy.

This item is an authentic OEM sourced O-ring kit that replaces worn or damaged O-rings for the gun, hose and wand.Unfortunately, over time o-rings will wear out and they may begin to crack eventually requiring replacements. Refer to the appropriate diagrams for your model to ensure the correct replacement procedure. A screwdriver and a wr...Read moreench set might be needed to take apart and reassemble the equipment. Note, this kit is sold as an individual item.

This bottle of oil is OEM and approved by the manufacturer. It is compatible with dozens of models of pressure washers. This one 4.6 oz bottle is the adequate amount of oil needed for the machine. A socket set is required to remove the plug on the oil pump. It is recommended to use a small funnel to pour the oil into the pump to prevent spillage.

It is a genuine OEM sourced item that is designed for Briggs and Stratton, Snapper and Troy-Built pressure washers. The manifold housing is an important component that attaches to the pump head. It houses the unloader valve, the check valves, the outlet tube and the chemical injection assembly. If the manifold housing is worn or damaged i...Read moret can cause water leaks and it should be replaced to ensure the equipment is functioning properly. To determine the exact location and the correct installation of this manifold housing, refer to the appropriate diagrams of your model. You will need a screwdriver and a wrench set to perform this repair. This high-quality manifold housing is made of durable metal and is sold as an individual component.

Frequently referred to as a Vibration Kit, this Vibe Mount Kit includes two durable rubber mounts, two metal washers, two bolts, and two locknuts. This kit is sourced directly from the manufacturer for use in pressure washers and attaches to the base of the unit to reduce vibration when the engine is on. When this part needs to be repla...Read moreced, you will notice more vibrations than normal coming from the unit. This part will become worn through regular use of the machine. You will need a socket set to complete this repair. Customers rate this repair as Easy.