Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
oven would not cook over 325 degrees and sometimes would burn your food.
15 of 19 peoplefound this instruction helpful.
phil from forney, TX
Really Easy
15 - 30 mins
Nutdriver, Screw drivers
I removed the unit from the wall,removed the back panel to access the wires to the sensor,cut the plug off of the new sensor and strip the wires back,used the wire nuts to attach the new sensor,put all back together and slid back into the wall and works excellent.
Was this helpful?
Thank you for voting!
Oven not heating
14 of 21 peoplefound this instruction helpful.
Joseph from Stuart, FL
Really Easy
15 - 30 mins
Screw drivers
It was very easy I removed two screws unpluged the sensor and wire spliced it together and also replaced the modual on the top of the stove and it was that easy.
Was this helpful?
Thank you for voting!
Oven would not maintain set temperature
11 of 16 peoplefound this instruction helpful.
Leonel from Biddeford, ME
Easy
30 - 60 mins
Screw drivers
No problem installing oven sensor, but I diagnose the problem wrong, I need to change(ERC-11)control p/n wb27k5140
Was this helpful?
Thank you for voting!
Burner "burned out" so we replaced the one and replaced the other that seemed to be cooling down.
13 of 23 peoplefound this instruction helpful.
Cheryl from Sequim, WA
A Bit Difficult
30 - 60 mins
Nutdriver, Pliers, Screw drivers
Basically removed the screws holding the op on and removed the vent from back. Just "figured it out" and now it works. Wish I could be more helpful. Recommend moderate experience and confidence.
The small burner inside the double burner shortd out.
5 of 5 peoplefound this instruction helpful.
david from PORT ORANGE, FL
Easy
30 - 60 mins
Nutdriver, Pliers, Screw drivers, Socket set
The first thing was to watch U-Tube . The replacement burner was being replaced in a GE glass top range. Exter tools were required than depicted in the U-Tube project. The project overall was not dificult for me however I was a general contracter for over 25 years
Was this helpful?
Thank you for voting!
Outer ring of burner did not work
5 of 5 peoplefound this instruction helpful.
Barry from Bradenton, FL
Really Easy
Less than 15 mins
Pliers, Screw drivers, Socket set
1- opened oven door 2- unscrewed 2 screws underneath top with a socket wrench 3- unscrewed clips that held burner 4-used needle nose pliers to pull off wire clips off old burner 5- placed wires onto new burner 6- opened clips to make it easier to reinsert burner 7-reattached burner 8-Replaced top
... Read morer />The hardest part was unscrewing the 2 screws that held the top in place due to the position of the screws
Read less
Was this helpful?
Thank you for voting!
outside element burned out
4 of 4 peoplefound this instruction helpful.
peter from westfield, MA
Really Easy
Less than 15 mins
Screw drivers
. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two plugs. plugged in the new element and screwed it in place
Was this helpful?
Thank you for voting!
broken inner glass
4 of 4 peoplefound this instruction helpful.
Sharon from EDISON, NJ
A Bit Difficult
1- 2 hours
Screw drivers, Wrench (Adjustable)
I removed the oven door by unlocking the hinges and pulling out. Set on workbench (with towel/pad) and removed handle, four screws, then bottom and inside panel screws, then one nut to finally be able to get at the inner glass insert. Removed insulation and then took an extra hour to really clean all surfaces (middle glass was quite gre
... Read moreasy due to inner glass being broken for a while. Reassembly wasn't bad, but took a while to figure out that the two thin 2" red spacers belonged around the two handle screws. This was tough to figure out as they come off when taking the handle off, but you can't see them, so didn't know where they came from! Anyway, if you're just a bit handy, you can do this job.
Read less
Was this helpful?
Thank you for voting!
Burner element was burnt
4 of 5 peoplefound this instruction helpful.
Chandra from Naugaeuck, CT
Really Easy
Less than 15 mins
Screw drivers, Socket set
It was very easy. First turn off the power. Remove two screws to pick up the hood then remove two screws holding the element. Tag the wires with number. Unplug the old burner attach the wires to new burner. Attach two screws with spring to hold the burner, put the hood down and put the screws holding the top hood.
Was this helpful?
Thank you for voting!
The front right outer element was defective.
4 of 5 peoplefound this instruction helpful.
Peter from Abbeville, LA
Really Easy
15 - 30 mins
Pliers, Screw drivers
My cooktop is a stand alone unit mounted in a counter top not associated with an oven. -Removed power to the cook top. Breaker off. -Lifted the cook top straight up from the counter top and placed two 24 inch board strips to support it above the counter top. This was very easy by pushing up from the bottom of the cook top. T
... Read morehis is a two person job preferably. -Removed the six phillip screws below the glass surface edge. 3 in the front, three in the back. -Remove knobs and remove the glass top by lifting straight up. -Record the wire positions on the element on paper and remove the connections. -The element is mounted on two spring loaded studs that have spring clips as a retainer. Remove the two clips by pulling straight up with a plier or needlenose. -The replacement element did not come equipped with the two mounting ears that the original had. I removed the two ears from the defective element and installed them on the new element. Very easy. Two phillips screws. The elements have perferations in the correct areas to accommodate this. -Placed the new element in position and reinstalled the spring clips. -Install the wiring terminals in the correct positions. -Reinstalled the glass surface and the six phillips screws. Reinstall the knobs. -Lower the cook top back into its counter top position. -Return power to the cook top. -Installation complete. Very simple!
Read less
Was this helpful?
Thank you for voting!
Oven door hinge roller deteriorated, oven door hard to open.
3 of 3 peoplefound this instruction helpful.
Craig from Kernersville, NC
Really Easy
Less than 15 mins
Screw drivers
Open and slide door upward off of hinges. Removed bottom drawer to access hinge spring. Detached spring, noting proper hole in hinge for reinstallation. Removed three screws holding hinge and removed hinge. Compared new part to old...exact match. Inserted hinge, and reinstalled the three screws. Reattached spring in hinge hole. Sli
... Read mored door back down onto hinges. Done in four minutes flat!
Read less
Was this helpful?
Thank you for voting!
oven door jammed,could not open it
3 of 3 peoplefound this instruction helpful.
Richard from Winchester, MA
A Bit Difficult
1- 2 hours
Screw drivers
Removed old hinges and installed new hinges. Hardest part was determining that worn hinges were the cause of problem, then ordering replacements. GE website hinge on exploded view did not look like hinges I removed.Thanks to Google I got on to PartSelect.com website where excellent pictures of hinges and one-inch grid confirmed they
... Read moresold exactly what I wanted for my 13-year old range, the model number of which was not even on the GE website.
The dual burnner had somthing drop on it and it went out
3 of 3 peoplefound this instruction helpful.
Thad from Layton, UT
A Bit Difficult
15 - 30 mins
Screw drivers
I pulled out the range from the wall unplugged it from the wall then i opened the oven door and removed the two small screws on the front off the range and lifted the glass top and supported it with a 1/2" X 18inc wooden dowel, then i removed the two burner retaining screws with a small Phillips screw driver and removed the wires from the
... Read more burner, then i replaced the burner with the new one and reconnected the wires and placed the burner in to the two retaining clips and then tightened the two screws then i removed the wooden dowel and installed the two screws on the front bottom side on the range then i plugged in the range in and tested the burner then put the range back against the wall.
Read less
Was this helpful?
Thank you for voting!
Inside burner would no longer heat
3 of 3 peoplefound this instruction helpful.
John from CHARLESTOWN, NH
Easy
15 - 30 mins
Screw drivers, Socket set
I went online and ordered the part after reading other people's repair experiences, confident that I could do it because the part was quite pricey. First, be sure you're circuit breaker to your range is off. Next, open the oven door and locate and remove two screws with a socket, that are just under the top surface which will allow you to
... Read more lift up the glass top which is actually hinged...no need to pull the range out. Securely prop up the glass surface area and the burners are exposed. With a marker, mark where each color wire goes on the burner you are going to remove and also mark where the two holding brackets are. This way you can reference the locations to connect to the new one. Carefully remove the wires and brackets and install new burner with brackets and connections. Close up the top, replace two screws, turn on breaker, and if there were no other faulty components,it'll work great. P.S Be gentle getting the very snug wires off. Good Luck
Read less
Was this helpful?
Thank you for voting!
Small front burner on our glass top stove died.
3 of 3 peoplefound this instruction helpful.
Robert from FLEMING ISLE, FL
Really Easy
15 - 30 mins
Screw drivers
Robert did not do the repairs. I did! 70 year old housewife. I watched a Utube video and thought I could certainly handle that. Ordered my part from your site. It came in two days. Burnet was replaced in under 20 minutes by me! Anyone can do this. Super easy, parts just plug in.
My Orders
