11047799701 Kenmore Washer - Instructions

Was able to remove old bellow without dis-assembly. Replacement required removing the front of the machine for access. Once the front was off, the bellow was simple to replace. Biggest difficulty is getting the top mark on the bellow lined up. It has a tendency to slip out of position while you are working the back of the bellow over th ... Read more e retaining lip and it is not possible to rotate the bellow after it is installed. Fortunately, the tube from the detergent tray can be rotated slightly to allow for a small amount of error. Replacing the front retaining wire and spring required three hands at one point, but was otherwise not a problem. Fortunately removal and replacement of the front of the machine is pretty straight forward. I needed to disconnect wires to set the front out of the way, but it is impossible to plug them back in incorrectly.

Just removed the bottom cover to access the water pump. Drained the water through the filter housing. One screw and two hose clamps and the pump was out. Installed new pump and checked for leaks. None found so the cover was secured in plase. Great news, WIFE is happy.

Snaped new one in place and done.

Followed the video on the website. Very easy to replace the part and it fixed the problem. The trickiest part was reinstalling the ring that holds the rubber gasket in place.

I removed the one screw that holds pun
mp in place. I pulled to the left and foward about an inch to remove hoses and unplug wire. then pulled pump assembly out. The new one went right in. The wire plug went right in without any customizing. I think this was about as easy as it gets.

simple repair. After reading other reviews my husband was confident he too could do the repair. He was right, we were so very glad not to have had to call for service.

It was so easy my wife replaced the part.

Replace bellow with help from Youtube video.

Easy fix,
I remove the front lower panel and the shocks where right in front of you , with a little twist with an adjustable wrench the cam right off . I removed and the replaced and it the same when you remove the back panel.
P.S when installing the shocks start by connecting to the bottom and then connect to the drum it will m ... Read more ake it lot easier.
Good luck on your repair

Removed three screws holding the cover, then one screw holding the pump assembly in place. After unplugging the power, it took two minutes to remove the clamp-rings from the hoses. The reverse was equally idiot-proof! But THIS "idiot" had 10-thumbs which added to the time to replace the lock rings! Added an extra 5 minutes at most! _g ... Read more rin_

I took off the cover, removed one screw. Removed two hoses and the electrical connector. It only 5 minutes to replace the old pump with the new one.

Take off top of washer and the flowmeter is in the back lefthand corner on the top of the washer. Replaced the water level switch on the top righthand of the machine also. Got about 150. 00 Total invested w/service call from local tech. F-20 has not came back yet. I hoped it fixed it washer is only 3 yrs. Old. -Gd

Starting getting these errors...but we had also been washing about 300 towels a week from our gym for about 3 months. I contacted an ex-sears repairman friend of ours for advise. He first recommended checking the pump filter basket. It was easy to get to by taking off the front panel. It did have about three hand wipes and other debris in ... Read more it. Removing these items did cause the errors to occur less often, but they still did continue. We had our repair friend come over and go through the diagnostics checks as per the instruction sheet that was on the inside of the washer. It came down to being the pressure sensor. After replacing the sensor, the washer has worked flawlessly.

removed 3 screws from back, then pulled hose of piece and disconnected wire clip. reassembled. have tu turn bottom of the piece torward you to remove from machine. this part is located on the back right side, black on my machine 1x2x2/4 inches in size, this is looking down into the wash machine from the front.

(These instructions improve on the excellent instructions provided by customer Franck from Anandale, Va.)
The first step is to remove the retainer wire and spring that holds the outside of the bellow in place.
To do this, Open the washer door as far as you can to get it out of the way. Look underneath of the front of the bellow ... Read more on the outside of the washer where it meets the door. Put your head almost on the floor and look up.
You will find a spring stretched about 3" connected to a small diameter wire (1mm.) that runs all the way around the outside portion of the bellow.
Use a small screwdriver or needle-nosed pliers to pull and pry the spring away from the rubber bellow. Be careful not to damage the spring or ring. Once you have grip on it, pull it carefully toward you then up and off of the bellow.

The front portion of the bellow is now free and can be peeled off. Start at any point and pull the rubber bellow in toward the opening of the washer, it comes off easily.
When you get to the detergent outlet on the upper left side, grab the plastic tube and carefully pull the bellow from around it. There is no adhesive or clamp holding this in place, just friction. Remove the rest of the front portion of the bellow.
Push as much of the bellow into the washer as possible to get it out of the way.

Once this is off comes the slightly tricky part. Look up at the top right portion of the bellow that is still attached. You may need to feel with your hand but you should be able to see it. This is where the flashlight or worklight will be helpful. You are looking for the screw/nut end of a giant hose clamp. This hose clamp goes around the entire bellow and secures it to the portion that holds the basket.
This is where the stubby screw driver comes in handy. There is not nearly enough room for a standard one and a nut driver or wratchet are too big. The nut will be pointing down and will need to be replaced the same way.
Loosen the hose clamp almost all of the way, perhaps 5 turns on the nut. It is not necessary to have the hose clamp come completely apart.
You can now remove the entire hose clamp from around the bellow by pulling it forward.
You will need to remove the hose clamp from the washer. To do this, squeeze it in from the sides about 6", don't kink it. Push it down toward the floor between the basket and the metal front panel. You will now be able to remove it from the top of the opening and be able to pull the bottom portion out.
Pull the old bellow completely out, very easy to do.

Time to install the new bellow. Figure out which side goes in and which faces out. The big hint is that the water inlet is on the upper left side.
You will notice at the top of the bellow on the portion that goes inside of the washer, you will find a small triangular shaped tab about 1/4" high. This is your centering mark. This will be at the very top. If you keep this at the top, everything will line up perfectly.

This next step takes a bit of dexterity because you need to slide both the bellows and the hose clamp into the machine with the triangular shaped tab on the bellow at the top as above. Unbend anything that might have bent on the clamp. Put a tiny bit of lube oil or Vaseline on the clamp screw thread to make it easier for your fingers to tighten it with the stubby screwdriver later. The hose clamp must go in now because once the bellow is slid over the detergent inlet tube the hose clamp can not be installed. Slip the bellow over the edge of the portion that holds the basket where you removed the old one. I started at the top and worked left so I could install the detergent inlet tube. Pull this through the bellow carefully. It doesn't take a lot of force. I found that wetting it with water made it easier to slide the bellow over it.
As you are pressing the bellow on this lip, you will notice that there is a 1/2" high back stop all of the way around. This is great because as you press it on, there is a positive stop and you can't go further than necessary. Continue to press it in all of the way around.
With the nut at the top or top right with the nut facing down to the floor while holding it vertically, squish it slightly inward, put the bottom portion in first then the top portion. Orient is as it was when you took it off. Slide it around the bellow. You will feel a positive stop. Run your fingers around the entire bellow to be sure the clamp is seated in the channel on the bellow and that the bellow is against its backstop. This assures you won't have a bad leak upon your next wash.
Grab the stubby screwdriver and tighten down the hose clamp. I did about a medium force when tightening. It doesn't take a lot of force.

Now it is time to pull the remaining part of the bellow out of the basket and fit it into place. Press it around the outside portion of the opening so it hooks over the lip. Now take the retainer wire and spring assembly and use it to clamp the bellow over the lip. After fitting the wire around