11047799701 Kenmore Washer - Instructions

Removed three mounting screws to the front access panel, removed panel, cleaned out drain trap, attempted to reset and drain washer, pump did not operate. Removed one wire harness to pump, two hose clamps and slipped pump assembly out of its mounting grommets, and installed new pump in reverse order. A sinch! And saved me approximately ... Read more $150.00 bucks in repair service fees.

slid new baffle into place. No directions with new part, fortunately it was easy to figure out how baffle locked into place.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

First and foremost, I usually call a real man to come do a job like this, but after reading the repair stories, I gave it a shot. Very, very easy. Pop of the bottom panel off (three torx screws), drain the water out of the tub (if any), and just follow the directions in the box. Anyone can do this one.

Overall, the install was easy.
Just a matter of getting yourself to get it done.
The video on the removal / install procedures was most helpful.
The front shocks were completed very quickly. The rear shock required all hoses to be disconnected and the back of the washer to be removed. After removing perhaps a dozen screws t ... Read more he cover was still fastened. You will see (in my case) 4 plastic flat clips. after they were removed the back came off. The rest of the project was the same as the front shocks. 1st time thru so to be expected.
Anyway, certainly a project that any DIYer can tackle.
Thanks Partselect for the correct parts in a timely fashion and the knowledge to perform the install.
Scott

baffle just clicked into place by aligining tabs on baffle with openings on drum. very easy.

looked repair on you tube followed instructions. took off broken latch. compared to pictures on sites. ordered part. part arrived in 2 days. put part on. suggest using first method quick and easy.

Brother who used to sell appliances opened the washer door and read the booklet inside the washer telling him the part necessary to repair the problem. $33/00 for the water flow meter Part and shipped in next morning and arrived overnight. Excellent service for only $7.00 shipping. Highly recommend this place for parts. This was after a ... Read more couple of days searching the internet for those with the same problem and not receiving and exact part to fix the problem

Tried all the Internet fixes and nothing worked. Bough the part put it in and BINGO! problem fixed. This is a class-action suit waiting to happen -- will never buy Whirlpool again. The stink problem persists despite cleaning and more cleaning.

Everything went great from order to done. Very happy

Remove three screws holding the lower panel, the pump is right up front. Probably the hardest part was holding the hose clamps open while attaching the hoses to the pump housing. One screw holds the pump assembly in place. Hold the over-ride switch closed, check for leaks, and replace the loser panel.

After receiving the hinge and screws, I watched the on line video at the website. I removed the door and hinge from the washer, removed the hinge from the door and re-installed the new hinge. The entire process took less than 15 minutes and reattaching the new hinge to the machine was a breeze. The replaced hinge is smooth as silk and ... Read more all is back on line. Great service from the crew at this site. Shipping was very quick (ahead of the scheduled arrival) and the CSR was very cordial and professional.

After researching the issue on the internet, I found that this was a consistent problem with my washing machine model. Located Part Select, phoned them with the model of the machine and told them what I wanted. Part was received within 2 days. Flipped circuit breaker leading to washer off. Took top off of machine, located the pressure ... Read more switch, had to twist to remove where it was attached to side of machine. Removed plug with wires, plugged into new switch & replaced to previous location. Machine runs like a brand new one (the longest time was trying to figure out how to get the switch unattached from the side of the machine). Disappointed with Whirlpool; couldn't say enough good things about Part Select!

This part slides in and snaps in place, a 15 second job.

Replacing the switch was extremely simple - just attached the hose, snapped in the electrical piece and snapped the part onto the side of the washer!