11026134610 Kenmore Washer - Instructions

1.) disconnect power to your washer. Turn off water supply and disconnect from the washer.

open the washer top and remove plastic cap from the wash plate

2.) using 7/16 socket, remove bolt from the wash plate. If you can't remove it with a socket , I recommend using impact wrench.

3.) remove wash plate ... Read more ( you might need to spray penetrating oil or wd40 inside the bolt hole to loosen it.
Check to make sure the wash plate gear grooves are not worn down, if they are, replace it.

4.) using your Maytag specific spaner nut wrench, remove the spaner nut from the shaft of the gear case. This should be right underneath where the wash plate was. If you can't turn it by hand , use a rubber mallet or hammer to encourage it.

5.) some people remove the wash basket at this point. I don't think it is necessary.

6.) close your washing machine. Tape the top closed to keep it from flying open. Tilt your washer back and prop it up where you have access to the underside of the washing machine.

7) remove motor rotor bolt and pull rotor off of the motor.

8.) disconnect the two wire connectors that supply power to motor. using a socket, remove bolts that are keeping motor attached to the gear case.

9.) Now that the gear case is all the is remaining on the underside, you can remove the 4 bolts that are holding the gear case to the washer. Now try to pull gear case out.

10.) if gearcase will not pull out, lower washer back to upright position. Spray penetrating oil or wd40 around the shaft of the gearcase and allow it to sit for 5-10 minutes. Using a hammer, lightly tap on the shaft of the gearcase and it should now fall out. ( you might have to apply penetrating oil again, or apply more force with the hammer.

11.) reinstall motor to new gearcase. Insert new gear case to the washer. Reinstall bolts and reconnect power supply wires.

12. ReInstall spaner nut inside the washer, reinstall wash plate.

Removed two screws on back of lid to raise top removed tub one bolt and one spanernut pulled tub lowered top reinstalled screws laid washer down to get to bottom of washer unplugged wiring removed four bolts pulled gear box and motor removed motor from gear box installed motor on new gear box reassemble washer

DIY'er working on a Maytag Centennial type washing machine should be aware that replacing a a transmission or agitator due to worn out splines is only half a job done well. I originally replaced my transmission due to worn splines, only to discover later that the worn agitator splines caused the new transmission splines to wear out at an ... Read more accelerated rate. Transmission and Agitator should be replaced together, along with a new Agitator mounting bolt. There are plenty of video's online of how to do this repair so I won't get into that here. Just wanted to drop the above sage advice. Transmissions for these washers aren't cheap.

Removed three screws on back to open top panel, used small vice grip to pull on suspension rod to unhook and remove from the drum. Remove and replaced one at a time so the rods keep drum suspended and prevent from dropping in the cabinet . Reinstalled top panel and done .Very easy completed in about 20 minutes.

The video was excellent in what needed to be accomplished. However it showed reaching inside the tub with vise grips to grab the old spring. This worked fine for removing them but the installation of the new spring did not allow my hand and vise grip to secure the new spring and pull it up and insert it into the retainer. I found that by ... Read more taking a cord and putting it through the socket and retainer allowed me to pull straight up and seat it in the retainer a lot easier.

I used a small flat head screwdriver inserted into slots just under the cap and pried off the cap. The cap should come off very easy.
Replace with the new cap.

Found video on line for my washer only had miner difficulties grabbing the hooked suspension rod to remove the ball end and lower tub to the floor. Do the front ones first then you can lay the washer front to the floor making it easier to remove the back ones

Popped the cap , used a socket to unscrew the bolt (it was stripped so ended up having to cut off bolt) Took off old impellar and replaced, installed a new bolt, replaced Cap and it was fixed.