This clutch slider kit is genuine OEM replacement kit that fits in various models of washing machine. It is a part of the transmission system in your washer which is responsible for controlling the movement of the agitator during the wash and spin cycles. The assembly includes the clutch band, slider, and lock ring. The kit helps to regul...Read moreate the speed and direction of the agitator or drum. It allows the machine to start and stop spinning smoothly, as well as change speeds as needed during the wash and spin cycles. If the clutch slider kit has worn or damaged components, it can lead to problems like difficulty starting or stopping the machine, excessive noise during operation, or failure to spin properly.
This is a clutch designed for use within top-load washers. The clutch is used to engage the transmission of your washer during the agitation and spinning cycles, to ensure it runs properly. If your washing machine is not agitating or spinning properly, the clutch could be the problem, and it will need to be tested and then potentially rep...Read morelaced. To replace the clutch in your washing machine, you will need to disassemble your washer from underneath, and will need a socket wrench and screwdriver as a result. This clutch is an OEM part and is only sold with a single securing screw.
This washer gearcase is a genuine replacement component engineered to restore the core mechanical functions of your washing machine. Also known as a transmission assembly, it drives both the agitator and the spin basket, ensuring effective washing and water extraction during the spin cycle. Compatible with select models from Whirlpool, Ma...Read moreytag, KitchenAid, and other affiliated brands, this OEM part is essential for resolving issues such as failure to agitate or spin, poor washing performance, unusual noises, or internal leaks. Replacing a faulty gearcase can significantly improve your washer’s efficiency and extend its service life. Installation should be performed with the appliance unplugged and may require moderate technical skill.
This suspension rod kit is a genuine OEM replacement designed to stabilize the inner drum of your washing machine and reduce excessive movement during operation. The kit includes four suspension rods, each approximately 27 inches long, along with the necessary securing components. These rods absorb vibrations and prevent the drum from ban...Read moreging against the cabinet, helping maintain quiet and efficient performance. Over time, suspension rods can wear out or break, leading to increased noise or instability. Replacing them requires partial disassembly of the washer and basic tools such as a screwdriver, wrench, and flat tool. Proper installation restores balance and protects internal components from damage.
This thrust washer is a genuine OEM component designed for top-load washing machines, serving as a critical interface between the agitator or impeller and the transmission. Positioned within the drive assembly, it helps secure the agitator while reducing friction between rotating parts, ensuring smooth and efficient movement during wash c...Read moreycles. Compatible with a wide range of models from Whirlpool, KitchenAid, Maytag, and related brands, this part replaces older part number W10665342. Its role in minimizing vibration and noise contributes to the overall performance and longevity of the appliance. Installation should follow manufacturer guidelines to ensure proper fit and function.
Presenting the genuine NUT-SPANER Spanner Nut from the renowned brand, Whirlpool. This authentic Spanner Nut is specifically designed to work with several models of washing machines by Whirlpool. It boasts of a superior OEM design, providing undeniable effectiveness and reliability. Attentively confirm that this part fits your machine bef...Read moreore ordering, as there can be minor variations in size and shape. Rest assured, installing nut W10909670 guarantees exclusive safety and efficacy. Opt for this Whirlpool Spanner Nut for the consistent maintenance of your household appliance.
This washer rotor is a genuine replacement component designed to drive the spin basket in select washing machines. It functions by generating a magnetic field that interacts with the stator, producing the torque required to rotate the drum at various speeds during wash and spin cycles. The rotor plays a critical role in ensuring smooth, s...Read moretable operation, reducing noise and vibration while enhancing energy efficiency. Common symptoms indicating the need for replacement include a washer that won’t spin, leaves clothes excessively wet, or produces unusual motor sounds. Compatible with a range of Whirlpool-family brand models, installation should be performed with the appliance unplugged and may require basic tools and reference to model-specific instructions.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Tom - For model number 11026134610
August 24, 2021
What keeps it from fulling draining during spin cycle? Why does "drn" error message appear when both hose from washer and standpipe/drain to street are clear?
Hello Tom, Thank you for the question. These issue indicate your washer isn't draining properly. We suggest checking the Drain Pump to make sure it is clear and there are no blockage. There are also Drain Hoses from the tub to pump you can check. If everything is clear, you may have a a defective Drain Pump, PartSelect Number PS11738156. We hope this helps!
Washer will not fill. Mixing valve on the fill valve is not getting power but there is power to the hot and cold solenoids. What would prevent just the mixing valve solenoid from powering?
Hi Eric,
Thank you for your question. If the mixing part of the water inlet valve is not working, then a component inside has malfunctioned and the water inlet valve will need to be replaced. The part number listed under your model number for the water inlet valve is PS12349461. If you would like to place an order for it, customer service is open 7 days a week and anyone will be happy to assist you. Please feel free to give us a call. We look forward to hearing from you!
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Loud grinding noise when the washer was in use.
69 of 84 peoplefound this instruction helpful.
Charles from STARKVILLE, MS
Easy
1- 2 hours
Nutdriver, Screw drivers, Socket set
1.) disconnect power to your washer. Turn off water supply and disconnect from the washer.
open the washer top and remove plastic cap from the wash plate
2.) using 7/16 socket, remove bolt from the wash plate. If you can't remove it with a socket , I recommend using impact wrench.
3.) remove wash plate
... Read more( you might need to spray penetrating oil or wd40 inside the bolt hole to loosen it. Check to make sure the wash plate gear grooves are not worn down, if they are, replace it.
4.) using your Maytag specific spaner nut wrench, remove the spaner nut from the shaft of the gear case. This should be right underneath where the wash plate was. If you can't turn it by hand , use a rubber mallet or hammer to encourage it.
5.) some people remove the wash basket at this point. I don't think it is necessary.
6.) close your washing machine. Tape the top closed to keep it from flying open. Tilt your washer back and prop it up where you have access to the underside of the washing machine.
7) remove motor rotor bolt and pull rotor off of the motor.
8.) disconnect the two wire connectors that supply power to motor. using a socket, remove bolts that are keeping motor attached to the gear case.
9.) Now that the gear case is all the is remaining on the underside, you can remove the 4 bolts that are holding the gear case to the washer. Now try to pull gear case out.
10.) if gearcase will not pull out, lower washer back to upright position. Spray penetrating oil or wd40 around the shaft of the gearcase and allow it to sit for 5-10 minutes. Using a hammer, lightly tap on the shaft of the gearcase and it should now fall out. ( you might have to apply penetrating oil again, or apply more force with the hammer.
11.) reinstall motor to new gearcase. Insert new gear case to the washer. Reinstall bolts and reconnect power supply wires.
12. ReInstall spaner nut inside the washer, reinstall wash plate.
Read less
Was this helpful?
Thank you for voting!
Washer making noise on spin cycle
20 of 29 peoplefound this instruction helpful.
Roy from MAYNARDVILLE, TN
Really Easy
30 - 60 mins
Nutdriver, Pliers, Screw drivers
Removed two screws on back of lid to raise top removed tub one bolt and one spanernut pulled tub lowered top reinstalled screws laid washer down to get to bottom of washer unplugged wiring removed four bolts pulled gear box and motor removed motor from gear box installed motor on new gear box reassemble washer
Was this helpful?
Thank you for voting!
Worn out splines connecting transmission driveshaft to agitator.
13 of 15 peoplefound this instruction helpful.
Thomas from MILLBURY, OH
Easy
30 - 60 mins
Nutdriver, Pliers, Screw drivers, Socket set
DIY'er working on a Maytag Centennial type washing machine should be aware that replacing a a transmission or agitator due to worn out splines is only half a job done well. I originally replaced my transmission due to worn splines, only to discover later that the worn agitator splines caused the new transmission splines to wear out at an
... Read more accelerated rate. Transmission and Agitator should be replaced together, along with a new Agitator mounting bolt. There are plenty of video's online of how to do this repair so I won't get into that here. Just wanted to drop the above sage advice. Transmissions for these washers aren't cheap.
My Orders
