1081 - Instructions

Took the roller out of the package, snapped it into place. Less than 15 seconds. Works good as new.

I looked under and found that 2 brass nuts that secured the heater element through the base housing of the dishwasher has split down each side of the nut and no longer was tight enough to keep water from leaking around either end of the heater element. I powered down the dishwasher at the circuit breaker and then reached under the dishwa ... Read more sher and pulled away the 2 wires that were attached to each side of the heater element. I removed the two nuts and replaced them with the parts I ordered from partselect.com. I then put the appropriate wires back at the end of the heater element and ran the dishwasher to check for leaks. No leaks... it was fixed.

First I noticed that the old gasket had disintergrated along the bottom. Next I removed the the gasket being careful to observe how it was installed. There are these notched areas of the gasket that belong in the lower corners. I think the notches are designed to help hold the gasket in place and make the gasket bend around the corner. ... Read more The gasket made closing the door very hard at first but after one wash cycle the fit became much more comfortable. The heat probably made the gasket more pliable. Problem solved.

removed the remnants of the old wheels and popped the new ones on....simple

Got to say, I was pretty amazed that I received my order the following day! You guys are wonderful!

Alighned the bracket and pushed in.

My door spring had broken and I was going to leave it until the door gasket failed and started leaking. After removing the parts, I got on-line and order what I needed. I found everything easier than I thought. I got the parts a few days later and put the gasket in first. Looking at it, you'll find theres slotted ribs at both ends. Those ... Read more areas go in the bottom corners because of the "S" curve. Simply push in and voila, you're done. At first the door will be firm to shut, but gets better- NO LEAKS! As far as the door spring...you don't have to remove the whole dishwasher. Simply unscrew the bottom plate under the door and reach in, rehook. Piece of cake. This site is wonderful. All the parts and easy to use.

Unplugged dishwasher, removed the 2 wires clipped to the heating element, removed both cracked nuts, replaced with new nuts from PartSelect, clipped on wires, plugged in and did a test cycle. Based upon service quote from Best Buy, I saved myself $125.00 for just the call out, not including parts and labor.

Pulled the dishwasher out. Removed the lower face panel , two screws on the top of panel and two screws on the bottom of the panel. Removed the two screws that hold the water valve and removed the valve, installed the new valve , installed the lower panel, put the dishwasher back in it`s position , turned on the water and checked for lea ... Read more ks, ran the dishwasher through a cycle , job done. Thanks to partselect for finding me the correct valve, my dishwasher is 12 years old and nobody else on the internet could help me get the right valve. Good price and fast shipping.

This is the second time in 17 years that the dishwasher had no water flow. Basically I diagnosed the valve being bad bcause I unhooked the output side of the valve and had no water flow. I then verified that there was water on the input side and also checked the I had voltage at the valve telling it to come on. With these symptoms I was a ... Read more ble to confirm the valve was bad.

I ordered a new door gasket, wich is not very common for these type of dishwasher anymore, I installed it in less than 15 minutes. I turned the machine on fully loaded and the machine did not leak a single drop. It save me a bundle since I was considering buying a new dishwasher. THANK YOU!!

We removed the bottom access panel, and were able to remove the broken spring. As others have suggested, we ordered two new springs, so we could replace them both at the same time. Unlike others, we didn't have to move the dishwasher out a few inches to access the springs. An easier repair than it might have been!

Unscrewed the dishwasher from counter, located in center front, pulled the dishwasher out, very easy, only about 12 inches, opened the door and saw where the springs went. The spring on the right was missing entirely. Hooked the new springs into place, closed the door, slid the dishwasher back into place. Took about 5 minutes. Thanks to t ... Read more his web site, and the fact that other people had reported how to do the repair. Only cost was that of the springs!

I turned the power off at the circuit breaker. I then took the access panel off the dishwasher at the bottom. I pulled the wire off the connector. I used a plied to remove the broken washer and replaced with new part. I put everything back in reverse order and ran the dishwasher. I than checked for leaks over two days while the machi ... Read more ne was running and everything was fine. Thank you Parts Select for saving me $500!

Very, very easy. Pop off the old wheels and snap the new ones into place on the rack.

Very easy fix, it's the second time I ordered this perticulsr part and it once again prolonged the life of this dishwasher for just a few dollars. The door seal arrived in just a few very short days and was easily installed with no tools in less than 10 minutes. The web site made locating, ordering, and paying for the part needed extr ... Read more emely once again. Thanks