1076 - Parts

This part is the replacement gasket for the crankcase on your engine. The gasket helps to create a seal on the crankcase and prevent leaks. If you notice that your engine is not running at peak performance, it could be because of a damaged crankcase. A damaged crankcase gasket can cause serious problems in your engine, so it is recommende...Read mored to replace it immediately if it is damaged. This product is gray in color and is sold individually. It is a genuine OEM part from the manufacturer.

This is a genuine Murray replacement part, it is sold individually. It is commonly used in lawn tractors, and is used in various places in the compatible models listed below. It is self tapping, with a 9/16 hex head. Made of metal.

This is a Genuine OEM Authorized Gasket used on variety of Lawn and Garden Equipment Engines. This part is made out of Rubber and it is sold individually. If the carburetor is leaking fuel it is recommended to replace the Bowl Gasket. Gaskets and O-rings are a common source of problems. They eventually shrink, causing fuel and air leaks t...Read morehat lead to poor engine performance. When replacing this Gasket you would need a Screwdriver and a set of Wrenches.

This authentic OEM starter assembly is designed for use with lawn and garden engines and is sourced directly from the original manufacturer to ensure quality and compatibility. The assembly includes a durable plastic shroud/housing, starter pulley, recoil spring, pull rope with grip, and the necessary hardware for installation. It functio...Read morens as the primary mechanism for manually cranking and starting the engine. To complete the replacement, you’ll need a wrench. Simply remove the four screws and nuts securing the old starter assembly, then install the new one using the included hardware. This item is sold as a complete individual assembly.

This is an authentic OEM replacement part used on lawn and garden engines. The purpose of this part is to mix air and gas before the fuel mix goes to the engine. This Carburetor is a auto-choke system. If the engine won't start and the tank is full of fresh fuel, test the carburetor by removing the air filter and pouring about a teaspo...Read moreon of fuel into the carburetor. Pull the starter rope. If the engine starts and then quickly dies, the carburetor is likely the problem. This assembly includes a metal body carburetor, rubber o-ring and a gasket. When replacing carburetor it is advised that you also replace carburetor gaskets to ensure proper air tight seal for optimum performance. You will need a screwdriver to perform this repair.

This is a manufacturer approved replacement part designed for use with a variety of lawn and garden engines. The air vane spring maintains the proper tension on the air vane choking system. If it is broken, it can cause the engine to not start. To replace it you will need pliers.

This ball bearing is sourced from the original equipment manufacturer and can be used in a variety of outdoor equipment. It has an inner diameter of 11/16 inches. The ball bearing provides support for the rotating parts in your equipment and reduces the amount of friction they are subject to during use. If the bearing is not adequately lu...Read morebricated or has worn down, you may hear grinding or squeaking from your equipment and notice excessive vibration when in use. It is important to address this issue promptly as a faulty ball bearing can potentially damage the parts located near it. To replace the ball bearing, use a pry bar or bearing puller to pry it out of its housing. Clean the housing thoroughly and press your new ball bearing in position. Note that when pressing the ball bearing into place, apply force only to the outer portion of the bearing.

This is a Genuine OEM replacement part used on a variety of Lawn and Garden equipment. The key helps to secure Flywheel in place. This is a Metal Key and it is Sold Individually. You would need Pliers to replace this item.

This OEM Locking Ring holds components or assemblies onto a shaft or in a housing/bore when installed in a groove. Installation is rated as "Easy" by customers and will require pliers. The part secures the drive pinion gear to the drive shaft, and if broken due to wear/fatigue/damage, it will need to be replaced.

The Lower Tube is a metal tube used to provide support for controlling the unit. It is part of the handlebar assembly. If there is any visible damage, the part should be replaced. It attaches from the rear frame to the top portion of the handle. Installation is rated as "Easy" by customers and requires pliers, a socket set, and wrench set...Read more. The part comes in black and is sold individually. Refer to your make, model and diagrams to ensure you've chosen the right part.

This is a genuine OEM sourced replacement part. It is designed for use with lawn and garden engines. It is an important part of the starter assembly that is used to crank start the unit. Please note shroud/housing, starter pulley, starter spring, grip, the pull rope and the hardware are all sold separately. This pawl plate is made out of ...Read moreplastic and it is sold individually. To complete this repair you would need a wrench.

This is a genuine OEM sourced replacement exhaust gasket. It is specially made for use with Briggs and Stratton engines commonly used on Toro lawn and garden equipment. Its purpose is to provide an air-tight seal between the carburetor and the exhaust tube. Over time this gasket will deteriorate requiring replacement. Please note, this co...Read moremposite gasket is sold individually. To replace this part you will need a wrench.