- Home
- 1069400080
- Instructions
1069400080 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Freezer shelf falling off
1 of 4 people
found this instruction helpful.
-
Carl from Crete, IL
- Really Easy
- Less than 15 mins
-
Pliers
One of the front studs was broken off. I had to use pliers to pull it out (kind of tight). Then I inserted the back and front holders and layed the shelf back in. Total time...10 min
Was this helpful?
Thank you for voting!
you have to turn it off and on to run.
0 of 1 people
found this instruction helpful.
-
chris from woodland hills, CA
- Really Easy
- Less than 15 mins
-
Nutdriver
Just like the video showed me.It still does not work. Have to turn it off and on to make it start up.I also replaced thermostat in freezer. Does not work.
Was this helpful?
Thank you for voting!
Refridger will not run unless tapping the control switch.
0 of 1 people
found this instruction helpful.
-
Victor from Colton, CA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
It was pretty straight forward after all the control panel removed. The plastic tubing was removed from old and installed on new part. Reconnected the connectors and re-route wire to the back vent. After installed covers and control panel, turn on power, it runs.
Was this helpful?
Thank you for voting!
After Hurricane Irene refrigeration compressore did not start
1 of 4 people
found this instruction helpful.
-
Bobby from New Bern, NC
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Followed the directions. Installation was quick. Took loner to put the covers back on and push the applicance back in position than the repair.
Was this helpful?
Thank you for voting!
Broken wheel under fridge
0 of 1 people
found this instruction helpful.
-
Ted from Magnolia, TX
- Really Easy
- 15 - 30 mins
-
Socket set
Replaced both since they came as a set. The only way it could have been any easier is if I had the wife do it. She had the remote this time. (•¿•)
Was this helpful?
Thank you for voting!
broken light switch
0 of 1 people
found this instruction helpful.
-
Atlee from Jupiter, FL
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Figured out You have to pop off the cocer than remove the 1/4 hex head screws only not the philips ones
Was this helpful?
Thank you for voting!
fridge kept running longer an was freezing
0 of 1 people
found this instruction helpful.
-
david j from monroe, MI
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
took front knobs off an then cover took side cover off next then disconnected themostat and replaced with new and followed the coil to side to the back of fridge an put back together. Oh by the way I unplugged the fridge first
Was this helpful?
Thank you for voting!
refriderator not running all the time
0 of 2 people
found this instruction helpful.
-
beverly beverly from north easton, MA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
followed directions given on your video
Was this helpful?
Thank you for voting!
The shelf stud support broke
0 of 2 people
found this instruction helpful.
-
Brian from Arlinton Hts., IL
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
I pried out the broken stud, and tried to put the new one in. There were no instructions, so I put it in, but it was loose and unusable. Also, I ended up with the wrong type of shelf stud - I had a rear one instead of a front one. So, I used gorilla glue and duct-taped the stud in place and let it harden overnight. It doesn't look gre
... Read more
at, because it sags a bit, but the glue is holding and the shelf stays up now.
Read less
Was this helpful?
Thank you for voting!
Noisy defrost timer
0 of 2 people
found this instruction helpful.
-
Jeffrey from Little Falls, NY
- Easy
- Less than 15 mins
-
Nutdriver
Part # had been replaced with another timer. Original timer had 2 wires coming out of it. Replacement only had 1 wire. Instructions showed 2 options for where to place the wire. I chose option 2 and I guess I was right. Installation took less than 15 minutes and refridge is back to normal. (Quiet)
Was this helpful?
Thank you for voting!
The refridgeror side was not cold enough
0 of 2 people
found this instruction helpful.
-
Patrick from Sun City, AZ
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
it was a simple repair once I located the part I had to replace . I really like your speedy delivery of the part I needed Thank you Pat Crotty
Was this helpful?
Thank you for voting!
Starting relay went out
5 of 18 people
found this instruction helpful.
-
George from Conroe, TX
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Forty years ago I serviced air conditioners and all kinds of refrigeration. At that time starting relays were electro mechanical, I hadn’t looked under a refrigerator in a lot of years and was surprised to find out that the new relays were solid state. The defective one had a bunch of broken pieces floating around in the case. I jury rigg
... Read more
ed a starting cord and confirmed that the compressor would start and looked at running current for thirty or so seconds. I ordered a new relay kit and it worked just right. I’m seventy five years old and it takes me longer to get up off the floor than it took to replace the parts. Your delivery was first rate the parts got here before I finished doing the paint touch-up on the door under the ice maker/water dispenser. Fed ex was easily three to five days faster than the brown truck.
Read less
Was this helpful?
Thank you for voting!
change relay
3 of 12 people
found this instruction helpful.
-
Robert from Boxborough, MA
- Easy
- 15 - 30 mins
-
Screw drivers
unplugged relay and plugged in
Was this helpful?
Thank you for voting!
Freezer was too cold and refrigerator was too warm
-
Jolinda from Eau Claire, WI
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
After receiving the part, I watched the installation video on the PartSelect website. The step by step demonstration was excellent. I felt confident I could do it myself after watching the video just once, and utilizing the written instructions that came with the part. The installation went smoothly, and my refrigerator is functioning
... Read more
correctly again. Best of all, I did not have to go through the hassle and expense of hiring a repair person!
Read less
Was this helpful?
Thank you for voting!
See below
-
Patricia from Hobe Sound, FL
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
The defrost timer that I ordered form you did the trick. My fridge was
running all the time and the fridge temp was 55 but the freezer was 10
below. The instructions did not say how to test the old one to compare with
the new on. However in the Readers Digest Home Repair book it did and the
test proved that it was defe ... Read more ctive. Your article said that with the system I
had, 65% on the time it was the timer. I ordered it and thank you it works
just fine. I do have another problem, maybe you can help. The fridge runs
for 6 minuets and stays off for 10 minuets. The temp in the freezer is 0
and the fridge is 35-40 on the warmest settings, but all is well.
Thank you
running all the time and the fridge temp was 55 but the freezer was 10
below. The instructions did not say how to test the old one to compare with
the new on. However in the Readers Digest Home Repair book it did and the
test proved that it was defe ... Read more ctive. Your article said that with the system I
had, 65% on the time it was the timer. I ordered it and thank you it works
just fine. I do have another problem, maybe you can help. The fridge runs
for 6 minuets and stays off for 10 minuets. The temp in the freezer is 0
and the fridge is 35-40 on the warmest settings, but all is well.
Thank you
Read less
Was this helpful?
Thank you for voting!