106835 Kenmore - Instructions

I tilted the unit back enough to scew the new legs into the threaded holes.

I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.

The Whirlpool water inlet valve was better design than the original. All I had to do was drill 2 holes to mount it since it didn't mount in the same location as the old one. I liked the push in connection for the water outlet to the ice maker better than the original plastic screw connection.

Replaced the valve and cleaned all the coils at the same time. The ice maker is spewing out ice. Wife is happy again.

Unplugged the fridge. Got a light to shine on 3 small screws. Used a pair of channel locks to get the pigtail wiring harness off and the old one was out. Put the new one back in, plugged in the wiring harness and heard the ice bin getting it's first new ice a few hours later.

After diagnosing the ice maker wasn't working, I got the model & serial number of the refrigerator. Picked the ice maker online by picture, that was a first. Three screws to take the old one out and replace the new. Written directions confirmed there is no manual cycle button on ice maker. Waited a couple hours and checked it, there was i ... Read more ce! Everybody was happy.

I pulled the socket out and unplugged the wires. I replaced the light socket by plugging in the wires and snapping the light socket into place. A very simple fix.

New inlet valve. very easy. Part select was great. I first ordered a new ice maker, this did not fix the problem. Part select allowed me to return it and get the right part. The repair vidio was great.

Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.

Searched PartSelect database for replacement. Double checked pictures on website to confirm exact replacement.

After locating the screws, removed icemaker, disconnected cable connection.

Verified new part side-by=side with replacement. Made needed mod to icemaker water inlet. Popped in replacement ice maker, conne ... Read more cted wiring harness, tightened screws. Waited for ice to arrive about an hour later.

Followed instructions from online video. Used the opportunity to clean the freezer compartment really well. Also discovered that water solenoid valve was failing and have since replaced that also.

While it probably could have been remedied with the controller, the cost difference between the controller and the unit made me opt for the entire unit. The fridge is a side by side, which meant in order for me to see the screws I'd need to use a mirror. Once I got the socket on the nut, it wasn't difficult to back out the upper screws. T ... Read more he lower was a bit easier. The power cable however was frozen from years of attachment, and really defied removal. Once removed, the unit came out easily. In my case, the wires had to be removed from the old unit and reinstalled in the new. Not a big deal, but just another step. the issue I had was upon re-installation. The wire harness didn't want to reassemble, and since I could only fit one arm inside, it was difficult to get the connector attached and tightened. I was able to get a pair of channel locks across the connector and get it together. Once that was done I hung the unit back on the upper screws, verifying the fill tube was properly set. I then re-tightened the lower screw. I then turned on the water and it seemed to take a very long time before the unit actually filled with water. It's now been several hours and the ice is starting to once again collect in the bucket.

Ordered new single outlet water valve, received in less than two days. Removed old one, and the repair pretty much feel in place. Instructions were there as a backup. ........ Just curious if the connection from the water source to the valve outlet connection could b a quick connect just the like the water line going directly to the ice ... Read more maker. Gregg in PA.

Looked up on youtube. found a guy who said that the shaded pole motors are made in china and rotate backwards. (design flaw) so, he had a 4 minute tutorial on how to reverse the motor and it runs the correct way.

I watched the demo on how to replace the ice marker and it was that simple. I removed three screws and unplugged it from the freezer. The difficult part was removing the wire on, off switch. You must pull it out carefully. It is a sung fit.