106835 Kenmore - Instructions

I removed the two attachment screws and lifted the old icemaker out and disconnected the plug. The new one was identical to the old one so the installation was just a reversal of the removal. The water soleniod was sticking from not being used so I took it apart and cleaned it. The next morning I had ice. The part arrived at my door in le ... Read more ss than 24 hours from my order placement.

Wathced video (VERY helpful)of how to do repair to make sure it was within my capabilities to do. Made sure I had all requested numbers before ordering. Replacement part was an EXACT fit. 15 minutes of work and I saved nearly $150 of estimate by local service company. I am (and will continue to be) a repeat customer. Thanks. Mel

The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!

I removed the 2 screws on top and the one screw underneath holding the Ice Maker to the wall of freezer.I pulled the electrical connection from the wall next (wiggled it back and forth until it came out).
I matched it up to the picture from this site and ordered the replacement unit.
When it arrived, it had a lot of extra parts ... Read more to match up to mine and any other fridge.
A good tip is to keep the old unit so you can configure the new unit the same. Although it was easy, this took me the longest of the entire job. Once this was done, it took me !0 minutes to plug the new unit into my fridge and then attach it back to the wall with the 3 screws.Not a hard job.Thanks

By going on line and going to PartsSelect, the check out procedures traced the problem to the start/overload relay. Using a nut driver, I removed the back panel and using their instruction, I installed the overload relay. On the next to the last step on the instruction, the sealer in the kit was already hardened. I called the service ... Read more hot line at PartsSelect and they apologized and sent me another kit to finish the repair. In two days, the new kit came and the repair was complete. The whole experience with PartsSelect was great.

First I turned off water supply. Then removed the two screws that attach ice maker, then disconnected the wiring harness.

Attached new ice maker in reverse order.

Removed the old ice maker (2 screws, about 2 minutes). Read the excellent instructions. Prepped the replacement unit by adding the mount bracket. It plugged straight into the existing fridge wiring harness. Amazing how standardized icemakers are! Total time for a very careful job was under an hour.

It came in the mail, I got ... Read more home about 5pm and had it installed that evening before dinner. First load of ice was in the catcher before I went to bed.

Very nice kit, and economical compared to a new fridge!

Removed Ice tray and flap followed by the three screws that held the old ice maker in place. (I probably didn't have to remove the top two, they are designed to just loosen and lift up on the mecanism to free.) I then pulled the old wiring harness out of the original ice maker. A small screw driver helped in depressing a tab while pulling ... Read more on the harness. The same process was used to remove the wiring harness that was attached to the new replacement unit. I connected the original wiring harness that I had disconnected from the bad ice maker, and it fit perfectly into the replacement unit. No need to splice or use any of the harnesses that came with replacement. I tried installing the new unit and discovered that there was interfernce with the water feed hose. I had forgotten to break off the tab on the end of the replacement unit. Once I did that using pliers, the unit fit fine. I tightened the screws, installed the on/off mecanism and replaced the tray and flap. I then waited and waited, hoping to hear the forgotten sound of water entering the ice maker. Had a beer and walked the dogs thinking I had failed, but low and behold, over an hour later, the ice maker turned on the water. Many hours later, my wife woke me up in the middle of the night to declare we had cubes! Success.

I just removed three screws from the old ice maker and disconnected a single set of wires. All I had to do was reconnect the new set of wires and screw it back into the side of the freezer. Anybody could do this repair.

Replaced the water valve. I knew that the ice maker was working by watching the movement. It was not getting water to it, s I figured it was the electric water valve and sure enough, that fixed the problem.

use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks

First 1/4'' nut driver was needed.Then i proceeded
to remove the nut just below the ice maker in a
white bracket. Then i loosen the two nuts at top of
icemaker,enough to lift it off the clips. Then that
allowed me to unplug the plug in rear socket. Then
you plug in the new plug that came with icekaker
and re ... Read more attach ice maker making shore the two top
clips slide into each other. Do not tighten unto you
incert bottom screw in lower bracket.Make sure
icemaker is push all the way up ,then tighen all
screws.

I first removed the bottom screw then loosened the top two screws about 3 turns lifted an then slide icemaker out a couple inches then used small screwdriver to unclip the wire conector and removed icemaker then pluged new icemaker in and tightened top screws replaced bottom screw lowered metal arm and was done. les than 10 min. it ha ... Read more s taken me longer to write this reply than it did to install the icemaker.

First removed 3 screws and took out old ice maker, punched out water inlet tube area in new ice maker connected the electric and screwed it back in. Within an hour...heard the ice drop. (I did not do the repair, my boyfriend did, however I think I could have done it.

This was an easy repair.

First I turned off the breaker that supplies power to the refrigerator, then I followed instructions to remove the old ice maker. I removed the bottom screw and loosened the two top screws and it came out easily.

The only unexpected problem I ran into was that the connection at the refrigera ... Read more tor end was 'hard wired', i.e., the wiring harness was not removable from the freezer.

After disconnecting the wiring harness from the old ice maker, all I had to do was plug the wiring harness into the new unit, slide it into place, then replace the bottom screw and tighten the two top screws.

Turned the power back on and had ice within 1/2 hour! : )