10658123701 Kenmore Refrigerator - Parts

This part does NOT include the water filter. The water filter is sold separately. The water filter housing holds the water filter and connects the water lines to the water filter.

This ice level arm, also known as an ice shutoff arm, is designed to detect the level of ice within the ice bin of your ice maker or refrigerator and turn it off when enough ice has been made. When the ice maker is empty, the arm will be down. When the ice maker is full, the arm will be raised, and over time, wear and tear to the level ar...Read morem can cause the ice maker to stop making ice completely. To replace this arm, unplug your appliance and remove the ice making assembly, then pull the levelling arm out of the assembly and place the new one. Consisting of a long, angled metal arm and a plastic flap, this level arm is a genuine OEM part that is compatible with a wide-range of refrigerators and icemakers and measures at approximately 9-inches by 4.5-inches.

For white, biscuit, black and stainless models.

This is an ice bin for the ice dispenser in your refrigerator/freezer. The ice bin collects the cubes dropped from the icemaker. Take note that the auger is not included with this container. If your current model is broken or damaged, it will need to be replaced. To make this repair you will need a 1/4-inch nut driver. This bin is white and made entirely of plastic. It is around 18 inches long and 12 inches wide.

This part is the replacement dispenser lever retainer for your refrigerator. It is made of metal and is approximately 2 inches long and ½ an inch wide. The bottom half of the dispenser lever retainer holds in the pivot points of the ice and water arms. If it breaks, the arms will be loose and can shake around. The top half springs the ice...Read more and water arms back into the original position, and if the retainer is broken, they will not be able to do this. The dispenser lever retainer is found behind the dispenser trim and can be removed with a ¼ inch nut driver. This part is sold individually and is an OEM part.

This screw is sold individually.

This kit includes the module motor, ejector arm, and ice stripper arm. The complete icemaker is sold separately.

This is an ice maker mold and heater assembly for a refrigerator ice maker. It is used with modular style icemakers and is located in the freezer section of the refrigerator. This ice mold is flake resistant which prevents the coating on the mold from flaking into the ice cubes when the ice mold begins to wear. The ice mold forms the ice ...Read morecubes and the heater allows the ice cubes to fall from the ice mold to drop them into the ice bucket. You will need to remove the ice maker from the refrigerator to access the mold and heater assembly. This is a genuine replacement part.

Sold individually.

The ice maker thermostat, also known as the cycling thermostat, controls and regulates the ice maker ejection cycle by monitoring the temperature inside the freezer to determine when to release the ice into the bin and start the ice making cycle again. If your ice maker is making unusual noises, or if the ice maker is not making or dispen...Read moresing ice, there could be an issue with the thermostat. Before you begin this repair, make sure the power is disconnected from your refrigerator, and that any food that may spoil is safely stored. This is an OEM part and is sourced directly from the manufacturer. This thermostat is sold individually, and comes with two attachment clips.

The light socket in your refrigerator houses the light bulb and connects it to the power source. If your refrigerator light is not coming on when you open the door, you may need to replace the light socket. Before you replace the light socket, be sure that your light bulb is in working condition, as this may solve the same problem. This l...Read moreight socket kit comes with 2 wire connectors, a light shield, and the new socket. The wire connectors that come with this kit are included so your new socket can replace a variety of old ones. If this light socket is different than your original, you will need to use the connectors to make it fit your refrigerator. Be sure to follow the instructions provided, so this part will fit your refrigerator properly.

Sold individually.