10658123701 Kenmore Refrigerator - Parts

If you have ice building up in your freezer, or if your freezer is getting too warm during the defrost cycle you may need to replace the bi-metal defrost thermostat. The function of the defrost bi-metal thermostat is to clip onto the evaporator and protect your evaporator from overheating during the defrost cycle. If your refrigerator doe...Read mores not defrost properly you can test both the thermostat and the heater to figure out which part is at fault. For this repair, you will need a Phillips screwdriver, a 1/4 inch nut driver, a flat blade screwdriver, a pair of wire strippers, a roll of electrical tape, and a few butt splice connectors.

This white ice bin auger drum comes with a washer.

In this kit you will find the support, the ice door, spring, and delay. The heater ribbon is no longer needed and therefore will not be included with this part. This kit works in the dispenser chute to let ice through when it is being dispensed. If you have the following symptoms such as: door sweating, difficulty opening or closing door,...Read more frost buildup, warm freezer section, or problems with ice dispensing, then this is a solution. The tools needed for this repair are a putty knife, needle nose pliers, and 1/4 inch nut driver. Wear work gloves to protect your hands when performing this repair.

This thermostat assembly is used in refrigerator units and freezers as a sensor. The thermostat senses the temperature increase in the evaporator during the cycle of defrosting and turns off when ice is melted. If you have any of the following symptoms, replacing your thermostat could solve the problem: fridge does not start, is too warm,...Read more too cold, runs too long, or will not start. The tools needed for this repair project is a putty knife, Phillips and flat blade screw driver, 1/4 inch nut driver, and needle nose pliers. Remember to unplug refrigerator from power source as a safety precaution. Refer to the manual provided by the manufacturer for further installation instructions.

This is a glass shelf for models of refrigerator. This part acts as a cover, a shelf, and a set of drawer slides all-in-one. This part includes a white plastic frame that doubles as drawer slides for the snack pan underneath and measures approximately 17.5-inches wide by 18.5-inches long, along with a glass insert that allows for items to...Read more be set on it. If your current glass shelf is shattered, cracked, or simply missing, it should be replaced. Replacing this shelf is easy, as you only need to carefully pull it out, then slide in the new shelf. This shelf is supplied by the original equipment manufacturer and does not come sold with any other parts than those mentioned.

This is an icemaker for your refrigerator/freezer. Take note that this part does not include the front cover, the wire harness, or the shut-off arm. These must be ordered separately or recycled from your old unit. This unit as a whole will allow your appliance to produce ice. This model makes eight radius ice cubes.If your ice maker is no...Read more longer making ice, dispensing ice, or if it is leaking, it will need to be replaced.

This condenser fan motor kit includes a motor, fan blade, wire harness, and screws. Used in a refrigerator, the condenser fan motor moves the condenser fan blade to direct and move air across the condenser coil. Please note: The manufacturer has changed the appearance of the product from the original. The kit still functions the same as t...Read morehe original part. It is an OEM factory replacement. Make sure to unplug the refrigerator from the power source and wear gloves to protect your hands. Also, a helpful tip is to store food to prevent deterioration when the power is off.

This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch. It has 6 threads. Refer to the manual provided by the manufacturer for further information on repair and accurate guidance. Remember to wear work gloves as a safety precaution.

This switch is located inside the dispenser.

This part is also known as a shelf frame. This drawer cover is for refrigerators. Drawer cover has rail brackets under the cover that hold the drawer and allow the drawer to slide in and out on the rails. Follow the instructions in the owner's manual or installation guide when installing this part. This comes with glass.

This part helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your freezer. If you are noticing temperature issues with your refrigerator or freezer, the run capacitor may need replacing. This repair is fairly easy to complete, and the only tools you will require are a 1/4 inch nut driver...Read more, and a 1/4 inch socket with a small ratchet. The run capacitor is located in the back of the fridge, so you will need to make sure you have room to work on this repair. Make sure to unplug the fridge prior to beginning the repair.

This refrigerator glass shelf serves as a replacement for the crisper pan cover and is designed to sit securely above the crisper drawers, providing both a protective barrier and additional storage space. Crafted from tempered glass, it offers a durable and safe surface that helps contain spills and maintain organization within the refrig...Read moreerator. The transparent design allows for easy visibility of items stored below. Measuring approximately 16.5 inches in width and 13 inches in depth, it fits directly into the existing white plastic frame without the need for tools or disassembly. Ideal for replacing cracked or broken glass, this shelf restores both function and appearance to your refrigerator interior. Sold individually.