1065779 Kenmore Refrigerator - Instructions

PartSelect was fantastic and I would recommend them to anyone! Online, Sears only showed a parts breakdown so I went to the service center. They could sell me an ice maker but PartSelect had the same ice maker for $35 less and it was on my door step the very next day! Mu husband plugged it in an we were on our way. You have been very easy ... Read more to work with. I was amazed at the delivery time and I will use you in the future!

Easy as pie, I followed the directions on the box that the replacement filter came in, and installed it and the cap simply and easily.

Unplugged refrigerator. Used nut driver to remove small bolt retaining wire cover on right side of ice maker. Removed wire cover, used flat head screw driver to depress side-rail clips. Ice maker slid out, unplugged. Timer module cover pops off easily. Three screws removed the timer module. Installation was reverse of removal. Had ice in ... Read more less than an hour, bin was full by next morning. If you have a screw driver and know what it's for, this job should come easily.

I removed the glides under the edges of the meat pan, remove the old pan, put the new pan in and replaced the glides. I was very pleased with PartSelect. I ordered my part, and it arrived the very next day. I will definitely order my next replacement part thru PartSelect.

removed screws that held the ice maker in place, then removed the cover (popped off) The drive element was easy to remove, three screws and it was out. I put in the new part and reinstalled the icemaker with the three screws that hold it in place. I never call Sears for any repair. They use contract help and I have heard horror stories ab ... Read more out those guys!

This is a side by side fridge. Both refrigerator and freezer quit working. I could here the combination start device click and try to start the compressor. It would shut back off within 5 seconds.Removed the lower rear cover on the fridge and cleaned the coils while it was off. Replaced the combination start device, plugged in the fridge ... Read more , and it worked. What a relief!

This was a pretty easy repair...I removed the retaining screws and slid the assembly off its tracks. Disconneting the wiring hardness was a pain but after a few minutes I had that off (use gloves, it gets cold in the freezer after a minute)

Once I had the unit completely out of the freezer the replacement part took only minutes ... Read more to replace.

Reversed the process putting the ice maker back in - a few hours later my ice buck was full again.

Simple repair - well worth the effort.

Turn off water supply too ice maker and unplug the fridge power. using a nut driver remove one bottom screw from the bottom, near the front. The other two from the side atop the ice mold. (loosen screws and ice maker will lift up and off.)
I set the ice maker on the counter, snapped of the front cover by hand. using a phillips d ... Read more river, remove two screws near the bottom corners.(they go through the circuit board into the ice mold)
circuit board in one hand, other end of ice mold in the other, slowly pull apart about 1 inch. remove the silver colored "on, off" bar at the end by snapping the retainer out of the ice mold. (the silver bar stays with the circuit board end)
Watch how the ice guide(white fingers stationary on side of ice mold) hooks too the ice mold on each end. swap ice guide to new ice mold, insert three guide pins on end into holes on the circuit board, while holding ice guide onto ice mold, watch rotation bar while inserting into motor.(it only splines one way.) when each piece is lined up, simply push together and reinstall two screws. snap circuit board cover into place. reinstall ice maker into freezer in reverse order.

MAKE SURE POWER IS OFF or REFRIGERATOR UNPLUGGED BEFORE STARTING THIS!!!
I removed the lower refrigerator backing. The compressor was located in the left corner of the refrigerator. I located the start device which had a thin clip on top of it. After removing the clip I pulled the 2 wires (Red and White) from the start device. I then ... Read more pulled the whole device from the compressor. You can use a screwdriver to pry it from the compressor. I unplugged the capacitor from the old switch and plugged it into the new one. Installed in reverse from how I took it out.

ridiculous how a tiny plastic broken part required a full motor assembly replacement. that being said, i went online, found this website and easily identified the part i needed to order. i was impressed when it arrived within a couple of days. removing the old motor and replacing the new was a piece of cake...and i am NOT mechanically i ... Read more nclined,

Removed the three motor screws pulled off old motor put new motor in place replaced screws and re-installed. It was producing ice three hours later. I originally tried to obtian these parts directly from Whirlpool in which twice they shipped me the wrong parts. Finally gave up on them and entered the whilrpool part number which crossref ... Read more erenced to new part number which was correct the first try. Thank you!

Ice Maker quit working. Seemed like a water supply issue but when I read the other reviews, I decided to install and see. bolted the bracket on with three screws, slid in place. Nothing happened and about 10 minutes later, I heard the water release to the ise maker and have been making ice ever since.

First of all, you must remove two screws in the fridge compartment, and then remove the back panel in the freezer compartment which snaps off easily.

Then, you must push the four clips on the back of the diffuser together from the freezer side so that it slips out the fridge side.

Make sure to remember the parts as ... Read more they come out, and re-connect them as needed to complete the repair.

This repair did not fix my fridge and so I'm drinking bourbon and trying to figure out how to fix this giant Kitchenaid piece of crap that freezes my beer.

Damn.

watched video. Very easy

I watched several video's on youtube that showed me how to replace the parts. Just Google "how to fix my freezer". I figured the only problem was the freezer Thermistor so I only replaced it. The refrigerator has one to. Instantly the freezer went back to Zero degrees and the defroster works fine after melting all the ice in the bottom ... Read more . Make sure the drain hole is cleared. I ordered the bi-metal thermostat just in case but I don't need it. Be sure and position the thermistor down in the freezer rail on the right side just to where you can see it in the first opening and pull it back up out of sight and tape it to the wall where it comes through from the air baffle. It's important that it's 7.8 " down from the top of the freezer. Happy now, Freezer 0, refrigerator 37. This thing use to run all the time, I'm saying electricity now.