1065707 Kenmore Refrigerator - Instructions

Patience is a virtue. The kit really works. 1st, lift the front plate of the ice dispencer by placing a flat head screw driver into the two slots at the bottom of the panel. When the panel is lifted up slightly at the bottom, push up on the panel to remove it. Careful not to break panel and the wires attached. Next, remove the wiring p ... Read more anel by removing the two screws on left and right sides. Then, unplug the old black ice cover from the wiring panel (this is the heating plug that you will nolonger need). Next, remove the parts and replace them with the parts in the kit, noting where each part comes from, etc. All parts in the kit are necessary and should be used. Some of the replacements need trial and error. Patience will be important. Also needed is a person that loves to solve problems, especially because the kit does not come with instructions. But the kit definitely works!

unplugged fridge, turned off water supply, disconnected water supply line (towel to catch drainage). remove cardboard lower panel from back of fridge. remove 2 bolts holding existing water inlet valve assy to fridge. Disconnect 2 electric plugs from assy. water lines disconnect using push/pull method (mark where they go). If any water tub ... Read more e line has any surface imperfections trim off a small length of line using a razor knife (cut tubing perpendicular (or "square" )on the end. I had to remove small unused part from the new water inlet valve assy. Insert the 3 water lines to the correct spots: push them on,fully, give a tug to make sure they are connected fully. Reattach the 2 electrical plugs.Bolt the unit back in place. I connected the water & plugged it in, filled about 10 glasses of water and made sure an ice cycle ran, to check for leaks (none found). I cleaned off some of the dust on the back of the fridge, reattached the cardboard lower piece. and listened to the sweet sound of Ice filling, and not my wallet emptying to the service man!!

I removed the ice maker from the refrigerator, by removing one screw on the underside bracket and loosening the two screws at the top side, then lifting the ice maker off the loosened screws. I then unplugged the electrical harness that supplies power from the refrigerator to the ice maker. I then disassembled the ice maker by removing ... Read more the front cover which is snapped in place, then removing two recessed screws at the front. I removed the broken part, I then reassembled the ice maker with the new part. I replaced the two recessed screws at the front and snapped on the cover. Then I reinstalled the ice maker in the refrigator by plugging in the harness, slipping the ice maker over the loosened screws in the refrigerator and replacing the screw that was removed from the underside bracket. Tightening all the screws completed the project.

1) removed the face plate that runs 3/4 way up the back of the freezer side. a total of 8 screws. (6")
2) disconnected the three electrical connections.(30sec)
3) removed the fan of the the old evaporator fan motor (5sec)
3) removed the fan motor (1")
4) put in the new fan motor (1")
5) put on the old fan on the n ... Read more ew fan motor(5sec)
6) reconnected the three electrical connections (30sec)
7) replaced the face plate on the back of the freezer (6")
Had re-frozen meat within 1 hour.

It was ridiculously easy. Push the button on the filter canister holder at the base of the refrigerator and the spring-loaded mechanism came out smoothly. I unplugged the old filter, took the cap off the new on and plugged it in. After reinserting the filter canister holder and locking it in place, I heard the whoosh of water once agai ... Read more n moving through the filter. Very satisfying and very easy to do.

first I backed off top two screws and removed bottom screw. unplugged wire harness. removed old icemaker. harness on new icemaker was the same. plugged in hung new icemaker on top two screws installed bottom screw. turned water on job complete and very easy. I was very satisfied with the whole process.

First checked to make sure the water reserve line inside fridge wasn't frozen (soaked coil at back of fridge in a container of warm water for 10 min). That seemed fine and icemaker was still working so assumed that portion of the water inlet valve feeding water line wasn't working. Video on PartSelect website showing how to replace the ... Read more valve was spot on and gave me confidence to install myself. Part arrived within two days and installation was done in a snap exactly as shown in video. All the lines & wire harnesses fit perfectly, water & ice working great, and I couldn't be more pleased.

The repair was extremely easy; after turning off the water valve on the back of the refrigerator, I removed the 3 screws (using a short length nut driver due to the confined space) and unplugged the harness. I did not need to splice the harness on the original ice maker and I simply plugged it into the new ice maker, screwed the unit bac ... Read more k on and turned the water back on. It's great to have plenty of ice without having to use the ancient ice trays.

My wife had overloaded the original plastic Pan-Crispr basket with too much cheese which caused the flange to break. The replacement basket from Partselect was an exact match and simply slid in.

I'll definitely come back to Partselect for accessories and parts.

I removed both plastic knobs from assembly faceplate. Then I loosened the screws holding thermostat housing to upper cabinet of fridge. Following this step, I loosened the screws of the thermostat to remove it. Next was the removal of the plate and vent pieces holding the thermostat wire sleeve in place. After removal of thermostat from s ... Read more leeve; all steps were reversed and unit was up and running normal (cooling) with no problems. "Ahh, it's nice to have cool again "

First I opened the fridge and removed the broken drawer. I then removed the new drawer from its shipping container and placed it on the tracks in the fridge. I then closed the fridge. Perfect!

Motor from Part Select was 185W instead of 260W that came out of unit. After a bit of searching online, I found out the 260W had been obsoleted for lack of torque when harvesting ice.

Removal instructions: Unplugged fridge. Then I removed the screw on the bottom right rear of the unit. Then removed the plastic cover that ... Read more covered the power connector. Pulled out the icemaker by pushing in the tab on the bottom left middle of the icemaker unit and pulling unit toward me. Unplugged the connector on the back right hand side. Removed the cover on the left side covering motor. Took out 3 philips screws and removed old motor with broken axle that spun freely (the source of the clicking noise). Put new motor in aligning harvest arm (the thing with the fingers) and did reverse of removal. Then plugged fridge back in and it started a harvest and the next morning I had a half tub of ice.

The easiest thing to do was pull the ice make off. After taking the 3 screws out of the wall of the freezer, take a screwdriver (flathead) and push on the tab for the electrical plug and wiggle the cord out. Then you can take 3 screws out for the main cover and another 2 screws on the next cover. There's the part, pop it out and replace h ... Read more olding pins and start the process of putting back together the opposite way you took it apart.

Trouble shot the electrical circuit per the electrical schematic and zeroed in when I noted the Defrost Timer circuit was open. When I tapped on the bottom of the timer it began functioning normally (for a few days). Ordered a new Defrost Timer Kit and along with the installation instruction, I watched the on-line video. It was very help ... Read more ful!!
After installation was complete, I plugged the Refrigerator into the electrical outlet and.......nothing happened! Hmmm!

Removed the Defrost Time Kit and inspected it for any damage and found none. Then I placed a flathead screwdriver to the manual advance knob and slightly rotate the gear mechanism. I heard a distance "click”. I believe the Timer was in the ‘defrost’ mode when received.

I reinstalled the timer, verified the wiring connections and this time plugged the Refrigerator into the electrical outlet and ….. it worked!!!

I unplugged the refrigerator, finished the installation per the instructions, plugged the unit in and monitored it for a few hours (just in case). That was a week ago and the Refrigerator is working like new.

The instructions were written in a manner which required re-reading a few times as they could be a bit vague. The video was what really helped and I appreciate PartSelect adding it to the instructions.

Did the diagnostics with the blinking light and couldn't decide what was bad....so ordered the control boards and the module motor assm. also. Turned out that it was the control boards and would suggest that future customers order that part first...if it isn't that then get the module and motor assm......these guys ship really fast and t ... Read more he prices are literally half of what Sears would charge, not to also mention the cost of their service man to walk through your door...OUCH!

Remove the front panel strip where the temperature adjustment lights show, use a thin screw driver to pot the strip out along the top. Use a nut driver to remove the control panel which contains the light, two bolts on the under side, two bolts on the front after the panel strip was removed. The control panel will hang down enough with ... Read more the wires attached to allow access to the thermostat. Use a Phillips screw driver to remove the side cover where the temperature probe runs along the left hand side to the unit, one screw. You will find the temperature probe inside plastic tubing running to the back of the unit where it is wrapped around a Styrofoam holder with three plastic retainer clips on the top and bottom. Unplug the thermostat from its electrical connection. You may want to unplug the unit’s wall plus as this is 110 volt connection. Remove the two screws holding the thermostat to the plastic control panel; remove the fiber optic connection to the light strip that runs across the top of the thermostat. Remove the temperature probe from the 6 clips and pull the entire unit out. Remove the plastic tube from the old temperature probe and slide it over the probe from the new thermostat. The probe is approximately 26 inches long and you must take care not to crimp it as you slide it in the plastic tubing(warm the plastic tube with a hair dryer to reduce stiffness at the bend). Plug the wires into the new thermostat and reassemble.