1013 - Parts

This wall vent cap kit comes with a spring loaded damper and instructions. It is designed for a 6" diameter outside vent.

This wall vent cap kit comes with a spring loaded damper. This part can be painted.

Made of durable rubber and plastic components, this Fuel Valve and Bushing are designed for use in over 150 models of generators and pressure washers. This item is sold as a kit, including the valve and the rubber cap. Its primary purpose is to deliver fuel from the tank to the carburetor. This part is found on the underside of the fuel...Read more tank and should be replaced when it is worn or damaged. When malfunctioning, it may cause your engine to be starved of fuel and run rough or not at all. You will need a screwdriver and pliers to complete this repair. Customers rate this repair as Easy.

This is a blower motor for your range, but you may also know it as a blower fan motor or a downdraft vent fan motor. This part is used with down draft models. It helps draw the steam and odors through the vent for the stove top when the switch is activated. The blower motor has a diameter of five inches. The shaft on this model has a 3/8-...Read moreinch diameter with a counter clockwise rotation. This motor includes the foam seal.

This blower wheel attaches to the ventilation motor to draw in and exhaust smoke, steam, and cooking vapors, helping maintain clean airflow in your kitchen. Built from durable metal for heat resistance and long-lasting performance, it measures approximately 7 inches in diameter and under 4 inches deep for a secure, efficient fit. Designed...Read more to spin smoothly on the motor shaft, replacing a worn or damaged blower wheel can restore proper airflow, reduce noise, and ensure reliable ventilation performance.

This circuit breaker is an important safety device found in the control box of your generator. It protects the electrical system from overloads and short circuits by automatically cutting off the electricity flow when it detects excessive current. It can handle a maximum current of 20 amps. You can tell if a circuit breaker is broken by c...Read morehecking for visible signs of damage, such as an unresponsive button, cracks, or burnt marks. If the circuit breaker repeatedly trips, the breaker may be faulty or overloaded. You will need a screwdriver, a set of pliers, a socket set, and a nutdriver to replace the breaker in your generator. Follow the instructions in your user manual to access the control box. You typically need to remove the carburetor and the fuel tank before removing the cover of the control box. Please note that this OEM replacement part is sold individually.

This is an authentic OEM part from Briggs and Stratton and Snapper for use with Generators. The fuel tank mounting grommet forms a cushion between the fuel tank and the fuel tank mounting bolts. The most common reasons for replacing the grommet is if the fuel is leaking from the fuel tank, the fuel lines are loose at the tank or the rubbe...Read morer grommet is cracked and not sealing. This part is made out of rubber and is sold individually. Here is a list of tools that are needed to replace the grommet a receptacle for draining fuel, a wire hook (to retrieve fuel lines), screwdriver, wire cutters or scissors.

This is an authentic item that is supplied by the original equipment manufacturer for use with Toro lawn and garden equipment. It is a standard hardware which has multiple applications depending on the model of your unit, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this i...Read moretem. Keep in mind this high-quality nut is made of durable metal and is sold individually.

The brush holder assembly in your generator keeps the brushes in place, allowing them to touch the rotor. It consists of a plastic brush holder and two carbon brushes with lead wires and attached springs. You can usually find the holder assembly inside the generator housing, near the rotor and stator assembly. If the holder assembly is br...Read moreoken, it can cause improper electrical contact between the brushes and the rotor, leading to a loss of electrical current transfer. Additionally, over time, the brushes will wear down from use, resulting in inconsistent contact with the rotor. Look for visible signs of damage like cracks, breaks, or deformations in the holder. A damaged holder can cause unstable voltage, power surges, or your generator failing to generate electricity altogether. To remove the existing brush holder assembly from your generator, refer to your user guide for detailed instructions. It may involve removing a cover or access panel to reach it. Use a nut driver or suitable tool to disconnect the assembly from the rear-bearing carrier and any connected wires. Remember to magnetize the brush assembly and conduct a generator test after installing the new one. Please keep in mind that this authentic OEM part is sold individually.

This is an original Briggs & Stratton replacement part. The screw is designed by the manufacturer for use in generators. This part is made of metal, and is generally used in securing the bearing cover. Please be aware that there are different screws used in the machine. Refer to the parts diagram to be sure of ordering the correct par...Read moret. You will require a wrench when replacing this item. This part is sold individually.