03033 Generator - Parts

The brush holder assembly in your generator keeps the brushes in place, allowing them to touch the rotor. It consists of a plastic brush holder and two carbon brushes with lead wires and attached springs. You can usually find the holder assembly inside the generator housing, near the rotor and stator assembly. If the holder assembly is br...Read moreoken, it can cause improper electrical contact between the brushes and the rotor, leading to a loss of electrical current transfer. Additionally, over time, the brushes will wear down from use, resulting in inconsistent contact with the rotor. Look for visible signs of damage like cracks, breaks, or deformations in the holder. A damaged holder can cause unstable voltage, power surges, or your generator failing to generate electricity altogether. To remove the existing brush holder assembly from your generator, refer to your user guide for detailed instructions. It may involve removing a cover or access panel to reach it. Use a nut driver or suitable tool to disconnect the assembly from the rear-bearing carrier and any connected wires. Remember to magnetize the brush assembly and conduct a generator test after installing the new one. Please keep in mind that this authentic OEM part is sold individually.

This bottle of oil can be used in over 150 different types of machinery. It is most commonly used for pressure washers and generators from manufacturers such as Briggs and Stratton and Troy-Bilt. This detergent oil is warranty approved and specially compounded for warm weather use. Please note: it is important to avoid over filling your engine with oil.

This is a genuine manufacturer-sourced replacement part which is designed for use with Snapper and Briggs and Stratton portable generators. Over time batteries will become weaker and eventually will not provide enough power to operate the equipment as it was designed. Several factors can cause this, such as improper charging or the way th...Read moree unit is used along with normal deterioration of the battery. Note, this high-quality battery is sold individually. Refer to the owner's manual for the correct application.

The set exercise switch attaches to the hour meter. This is a genuine Briggs & Stratton part sourced directly from the manufacturer for use in generators. This part is available as an individual replacement. It is made of plastic and metal and may require a wrench during installation. It might become broken and will need to be replaced.

The metal screw attaches to the muff guard bracket. It is a genuine replacement part sourced from the original manufacturer for use with blowers, engines, generators, pressure washers, snowblowers, and vacuums made by Briggs & Stratton, Toro, and Lawn Boy. This item is available as an individual replacement part. When replacing this screw a wrench will be needed. It will need to be replaced if it strips or breaks.

This rear bearing cover is designed to protect and insulate the rear bearing of the engine. It is an authentic OEM replacement part with a diameter of approximately 8 inches. It comes with a center/dust cap for easy access to the bearing. The cover acts as a barrier that prevents dirt and other contaminants from entering the bearing and p...Read moreotentially damaging it. It also protects the bearing from harsh environmental conditions and keeps it adequately lubricated. Over time, the cover may crack or break, leaving the bearing exposed. A faulty cover will result in several issues such as excessive noise and vibration, increased friction and wear, overheating, and lower overall equipment efficiency. To complete this repair, pry the center cap off first and then detach the old cover from the rear bearing. Clean the mating surface, align the new cover with the bearing, and snap the center cap into position.

This is an authentic OEM sourced part which is specially made for DeWALT planers. It functions as a safety device. When the circuit becomes overloaded, this circuit breaker switch interrupts the transfer of electricity to the motor. Flip the switch on the circuit breaker to reset the connection. Please make sure to refer to the appropriat...Read moree diagrams for your model for the correct location and application of this component. Keep in mind this high-quality circuit breaker is sold as an individual item.

This is a genuine replacement part sourced from the original manufacturer for use with small engines. The special gasket is commonly used to seal the connection between the exhaust manifold and the cylinder head. This special gasket is available as an individual replacement part, please see model diagram for associative parts.

It is an authentic item that is supplied by original equipment manufacturer, it is specially produced for use on Briggs and Stratton and Snapper generators. This kit is used to secure the engine to the main frame, it is designed to help reduce vibrations from a running engine. Over time the material may deteriorate and get compressed caus...Read moreing the generator to vibrate more than usual, if this happens replacing the mount should resolve the issue. It is a complete kit which includes one metal mount with a rubber pad, a screw, and three locknuts. Please note this replacement kit is sold individually.

This is an original Briggs & Stratton replacement part. The screw is designed by the manufacturer for use in generators. This part is made of metal, and is generally used in securing the bearing cover. Please be aware that there are different screws used in the machine. Refer to the parts diagram to be sure of ordering the correct par...Read moret. You will require a wrench when replacing this item. This part is sold individually.