Official KitchenAid Air Conditioner Parts | Order Today, Ships Today

Your Price

$17.95

WASHER

★★★★★

(1)

PartSelect Number PS12578732

Manufacturer Part Number W11236646

This part is located on the drum roller support shaft in your dryer appliance. The exterior of the washer is 1 inch in diameter with a hole in the middle and is made of metal. They are installed alongside the drum support rollers and idler pulleys. If you notice that your dryer is making an unusual sound it could be due to the washer becoming loose on the drum support. They help prevent the rollers and pulleys from bumping up against the brackets they are installed on. If you are replacing the rollers, we suggest you replace the washers at the same time.

Fixes these symptoms

Noisy
See more...

Installation Instructions

John from Tucson, AZ

worn out part

The repair was fairly easy. The most timely part of the repair was removing the twelve screws from the back panel to expose the repair. Read more...

Silicone Rubber Adhesive - 2 oz – Part Number: WP279368

Your Price

$47.14

Silicone Rubber Adhesive - 2 oz

PartSelect Number PS11740605

Manufacturer Part Number WP279368

Silicone rubber adhesive is a high temperature adhesive that is used for gaskets on dryers and felt seals. It is used on many different appliances for many different application reasons. This silicone paste creates a waterproof seal between components. This product is a 2 oz. tube. Unplug your appliance if you will be working on any internal workings and applying this sealant. Wear gloves to protect your hand from accidently applying sealant to your skin. The surface must be clean, dry, and free from oil and grease. Coat one surface and let it dry for at least one minute and then bond.

Your Price

$20.88

Motor Clip

★★★★★

(2)

PartSelect Number PS11757442

Manufacturer Part Number WPY015825

Sold individually.

Installation Instructions

Jeffrey from Bend, OR

Rumble noise and groaning on startup.

I found that I replaced more parts than I needed to fix fhis problem. The source of the rumble was the blower wheel connection to the motor, allowing the wheel to wobble (plastic wheel flat spot worn off over time, no firm lock to the motor shaft). But the dryer should be good for another 10 years!

Disconnect dryer from electrical outlet and exhaust.

Remove the back access plate to release the belt from the pulley. Remove the two screws at the bottom front of the dryer, rotate the front to release it at the top. Remove the wires from the door status switch. Remove the 4 nuts holding the drum support frame and pull straight out. Remove the drum. Remove the two bolts holding the thermostat cover (silver odd shaped metal plate at the front of the dryer). Remove the dryer blower cover plate by removing the 6 bolts holding it to the blower housing. Remember to remove the bolt holding the plate to the bottom of the dryer. Release the door status wire from the clips on the left side of the dryer and set the blower housing plate to the right, out of your way without removing the wires. Remove the blower wheel by removing the Circlip at the front of the shaft and then removing the shaft compression clip. Pull out the blower wheel and then remove the rear Circlip from the motor shaft. The back of the blower housing can be removed by removing the 4 bolts holding it to the motor support frame to make access easier but this may not be necessary. Release the 5 wires attached to the motor. Release the front and back motor clips. I used a large straightblade scerwdriver to press down and out on the end of the clips. Lift out the motor. Remove the rear pulley from the motor using an allen wrench and transfer it to the new motor. Set the new motor in the support frame, ensuring the lips of the vibration isolation rings are pointed down to slip over the frame and are not facing up towards the clips ( makes clip instalaltion much easier). Hook up the wires, following the color coding on the motor controller you are attaching to. Reinstall the blower back housing if removed, rear circlip, blower wheel, front circlip, shaft compression clip, blower housing front cover (Including the bolt to the dryer bottom) , reroute the door switch wire up the left side, reinstall the thermostat cover, reinstall the drum and belt, reinstall the drum front support frame (ensure the felt seals for the drum and the blower cover are properly aligned and seated correctly), hook up the door status wire when your set the front cover and install the 2 screws, reinstall the belt through the pulley and idler wheel (make sure the belt smooth side is against the drum) through the back access panel and reinstall the panel. Read more...

Your Price

$9.24

Hex Nut

★★★★★

(2)

PartSelect Number PS11742711

Manufacturer Part Number WP488130

This hex nut is an authentic Whirlpool part that is sourced directly from the original equipment manufacturer, and will fit a variety of appliances including ovens, microwaves, refrigerators, air conditioners, and dishwashers. It is a metal part with a threaded hole to fasten parts in the appliance together. It is common for this part to wear out; it is recommended to order a spare. To replace this part the tools needed are a nut driver or wrench. This nut features a built-in external tooth lock washer, which is used to help keep the nut in place.

Your Price

$7.76

Zip Tie

PartSelect Number PS11753208

Manufacturer Part Number WPW10339879

Your Price

$10.76

Control Knob

★★★★★

(2)

PartSelect Number PS11738317

Manufacturer Part Number WP1158054

This air conditioner control knob is gray in color, and measures approximately 1 inch in diameter. This replacement part allows you to properly control all the air conditioner settings. If your knob has broken or gone missing it will need to be replaced. This repair requires no tools to complete. You simply remove the old knob by pulling it off and press the new knob into place by lining it up with the shaft. This genuine OEM replacement knob is sold individually.

Installation Instructions

David from Nashua, NH

Dosen't seem to fit.Won't go all the way on.

put the knob on and pushed it as far as it would go. Read more...

Your Price

$47.84

VALVE

PartSelect Number PS403685

Manufacturer Part Number 978030

Your Price

$5.18

Control Knob

★★★★★

(1)

PartSelect Number PS11738318

Manufacturer Part Number WP1158639

Installation Instructions

JOHN from BLOOMFIELD, NM

broken control knobs

I opened the package. I tool out the plastic bag containing the replacement knobs. (I ordered two). I lined up the knob that needed replacing and pushed it on. The replacement knobs are of a better quality than the original and shouldn't break like the old ones. After this repair I was exhausted and took a nap. Read more...

Your Price

$54.64

Air Filter

PartSelect Number PS11738347

Manufacturer Part Number WP1166750

This part is used for room air conditioners. The air filter in your at-home air conditioner keeps dirt, dust, and other airborne particles from getting into your home. Over time, these particles will build up and your air filter will need to be replaced. This is an OEM part sourced directly from the manufacturer. In order to complete this repair, simply remove the old air filter and replace it with the new one. Many of our customers find this repair to be easy, and describe it as taking less than 10 minutes. This product is sold individually.

Installation Instructions

FLARZELL from LIVE OAK, FL

Reuseable A/C Filter 16 Yrs Old

Pull out old filter and insert new filter received from. I was surprised how easy it was to order and how prompt the service. The web site was really easy. That can't be said for many web sites Read more...