KitchenAid Air Conditioner Hardware
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular KitchenAid Air Conditioner Hardware
Your Price
$7.47
In Stock
KitchenAid Air Conditioner Cover Screw
In this spirit of any repair, I replaced them, and it was not the issue. I don't know what I expected.
Ceiling. YouTube. Pacing.
Then I figured it was this part - the motor coupling. I unplugged the machine and took out the drain tube. I leaned the machine back and propped it up with an empty detergent bottle, because those were abundant. Ratchet off a few bolts and the motor comes out. The coupling was indeed broken. The new one slips right in - I tapped it a few times with a mallet for good measure / vengeance. Ratcheted the bolts back on and tipped it back up.
Pros: Washer works now.
Cons: Everest-esque laundry pile to address.
But hey, it worked! I am no handyman and it wasn't too bad at all. Half hour tops. Read more...
PartSelect Number PS11740701
Manufacturer Part Number WP308685
Sold individually.
Installation Instructions
Peter from WRENTHAM, MA
Kenmore 80 Series Washer - Agitator Stopped Working
First I screamed at the ceiling, because I have a three year old and an infant, and the washing machine was dead. Then I went to youtube. It seemed like the "agitator dogs" were the issue. In this spirit of any repair, I replaced them, and it was not the issue. I don't know what I expected.
Ceiling. YouTube. Pacing.
Then I figured it was this part - the motor coupling. I unplugged the machine and took out the drain tube. I leaned the machine back and propped it up with an empty detergent bottle, because those were abundant. Ratchet off a few bolts and the motor comes out. The coupling was indeed broken. The new one slips right in - I tapped it a few times with a mallet for good measure / vengeance. Ratcheted the bolts back on and tipped it back up.
Pros: Washer works now.
Cons: Everest-esque laundry pile to address.
But hey, it worked! I am no handyman and it wasn't too bad at all. Half hour tops. Read more...
Your Price
$7.47
In Stock
KitchenAid Air Conditioner Screw
PartSelect Number PS11742721
Manufacturer Part Number WP488729
Metallic screw that is less than an inch long. Does not include the plastic washer.
Installation Instructions
Kyle from Wimauma, FL
Black Cam was bren on lower door hinge
This was a very simple job. Remove the top Hinge bracket, a total of 4 screws, lifted the door off the bottom hinge, removed the bottom hinge set up, 2 screws, replaced it, and attached the new bottom black door cam, lifted the door back onto the bottom hinge and aligned the top hinge, and reinserted the screws, and Ta Da, The door works like a new refrigerator door. 15 to 30 min tops. I did not even have to take the refrigerator items out of there door holder.
Read more...
Your Price
$22.52
In Stock
KitchenAid Air Conditioner Washer
PartSelect Number PS12578732
Manufacturer Part Number W11236646
This part is located on the drum roller support shaft in your dryer appliance. The exterior of the washer is 1 inch in diameter with a hole in the middle and is made of metal. They are installed alongside the drum support rollers and idler pulleys. If you notice that your dryer is making an unusual sound it could be due to the washer becoming loose on the drum support. They help prevent the rollers and pulleys from bumping up against the brackets they are installed on. If you are replacing the rollers, we suggest you replace the washers at the same time.
Fixes these symptoms
- Noisy
- See more...
Installation Instructions
John from Tucson, AZ
worn out part
The repair was fairly easy. The most timely part of the repair was removing the twelve screws from the back panel to expose the repair.
Read more...
Your Price
$7.47
In Stock
KitchenAid Air Conditioner Refrigerator Single Hex Head Screw
PartSelect Number PS11742731
Manufacturer Part Number WP489069
Sold individually. The size of this screw is 1/4" hex head and 10-12 x 1/2".
Installation Instructions
Chris from Pompano Beach, FL
Water in bottom of dishwasher
Disconnected power. Shut off water supply. Took off the front, disconnected copper supply line and flexible water line, removed water inlet valve. Took elbow from old inlet valve and put in on new one. Put new valve in, reconnected water lines, put back front panel. Opened water supply, Flipped breaker back on. Done and it worked!
Read more...
Your Price
$20.37
In Stock
KitchenAid Air Conditioner Dryer Motor Clip
Disconnect dryer from electrical outlet and exhaust.
Remove the back access plate to release the belt from the pulley. Remove the two screws at the bottom front of the dryer, rotate the front to release it at the top. Remove the wires from the door status switch. Remove the 4 nuts holding the drum support frame and pull straight out. Remove the drum. Remove the two bolts holding the thermostat cover (silver odd shaped metal plate at the front of the dryer). Remove the dryer blower cover plate by removing the 6 bolts holding it to the blower housing. Remember to remove the bolt holding the plate to the bottom of the dryer. Release the door status wire from the clips on the left side of the dryer and set the blower housing plate to the right, out of your way without removing the wires. Remove the blower wheel by removing the Circlip at the front of the shaft and then removing the shaft compression clip. Pull out the blower wheel and then remove the rear Circlip from the motor shaft. The back of the blower housing can be removed by removing the 4 bolts holding it to the motor support frame to make access easier but this may not be necessary. Release the 5 wires attached to the motor. Release the front and back motor clips. I used a large straightblade scerwdriver to press down and out on the end of the clips. Lift out the motor. Remove the rear pulley from the motor using an allen wrench and transfer it to the new motor. Set the new motor in the support frame, ensuring the lips of the vibration isolation rings are pointed down to slip over the frame and are not facing up towards the clips ( makes clip instalaltion much easier). Hook up the wires, following the color coding on the motor controller you are attaching to. Reinstall the blower back housing if removed, rear circlip, blower wheel, front circlip, shaft compression clip, blower housing front cover (Including the bolt to the dryer bottom) , reroute the door switch wire up the left side, reinstall the thermostat cover, reinstall the drum and belt, reinstall the drum front support frame (ensure the felt seals for the drum and the blower cover are properly aligned and seated correctly), hook up the door status wire when your set the front cover and install the 2 screws, reinstall the belt through the pulley and idler wheel (make sure the belt smooth side is against the drum) through the back access panel and reinstall the panel. Read more...
PartSelect Number PS11757442
Manufacturer Part Number WPY015825
This motor clip is an original manufacturer replacement clip used to secure the motor in your home appliances. It holds the motor firmly to its housing to prevent shaking and potential damage while the appliance is in use. Over time the clip can fail due to exposure to high temperatures, vibration, and humidity resulting in an unstable motor and decreased performance. Remove and discard the faulty clip and place the new one in its position. Align it appropriately with the motor and mounting bracket before securing it in place. Be sure to check your equipment specifications as your appliance may require two clips to complete the repair, and this clip is sold individually.
Fixes these symptoms
- Noisy
- See more...
Installation Instructions
Jeffrey from Bend, OR
Rumble noise and groaning on startup.
I found that I replaced more parts than I needed to fix fhis problem. The source of the rumble was the blower wheel connection to the motor, allowing the wheel to wobble (plastic wheel flat spot worn off over time, no firm lock to the motor shaft). But the dryer should be good for another 10 years!Disconnect dryer from electrical outlet and exhaust.
Remove the back access plate to release the belt from the pulley. Remove the two screws at the bottom front of the dryer, rotate the front to release it at the top. Remove the wires from the door status switch. Remove the 4 nuts holding the drum support frame and pull straight out. Remove the drum. Remove the two bolts holding the thermostat cover (silver odd shaped metal plate at the front of the dryer). Remove the dryer blower cover plate by removing the 6 bolts holding it to the blower housing. Remember to remove the bolt holding the plate to the bottom of the dryer. Release the door status wire from the clips on the left side of the dryer and set the blower housing plate to the right, out of your way without removing the wires. Remove the blower wheel by removing the Circlip at the front of the shaft and then removing the shaft compression clip. Pull out the blower wheel and then remove the rear Circlip from the motor shaft. The back of the blower housing can be removed by removing the 4 bolts holding it to the motor support frame to make access easier but this may not be necessary. Release the 5 wires attached to the motor. Release the front and back motor clips. I used a large straightblade scerwdriver to press down and out on the end of the clips. Lift out the motor. Remove the rear pulley from the motor using an allen wrench and transfer it to the new motor. Set the new motor in the support frame, ensuring the lips of the vibration isolation rings are pointed down to slip over the frame and are not facing up towards the clips ( makes clip instalaltion much easier). Hook up the wires, following the color coding on the motor controller you are attaching to. Reinstall the blower back housing if removed, rear circlip, blower wheel, front circlip, shaft compression clip, blower housing front cover (Including the bolt to the dryer bottom) , reroute the door switch wire up the left side, reinstall the thermostat cover, reinstall the drum and belt, reinstall the drum front support frame (ensure the felt seals for the drum and the blower cover are properly aligned and seated correctly), hook up the door status wire when your set the front cover and install the 2 screws, reinstall the belt through the pulley and idler wheel (make sure the belt smooth side is against the drum) through the back access panel and reinstall the panel. Read more...
Your Price
$7.47
Special Order
Your Price
$7.47
On Order
KitchenAid Air Conditioner Zip Tie
PartSelect Number PS11753208
Manufacturer Part Number WPW10339879
A zip tie, also known as a cable tie or a wire tie, is a fastening device that holds wires or tubing together. If a machine has wires or tubing that are easily shifted, you need to hold them tightly together using a zip tie. It is a flexible, plastic strip that has serrated teeth and a locking mechanism. If the zip tie is damaged, it should be replaced. Freely moving wires may rub against surfaces, causing them to break over time. Zip ties are single-use and may not be reused after they are removed from a machine. To release the locking mechanism, you will need to insert a small flat tool into the head of the zip tie, between the tongue and the serration, and depress the bar. You can then pull the teeth out of the mechanism to loosen the cable tie. This part is produced by the original equipment manufacturer and is sold individually.
Your Price
$6.40
Special Order
Your Price
$6.40
Special Order
Your Price
$9.62
In Stock