Kenmore Stove Parts
Find your part
Enter your model number or a part number and click "Search"Here is an example model number plate:
Popular Kenmore Stove Parts
Your Price
$14.72
40WATT 15AMP INCANDESCENT BULB
PartSelect Number PS217532
Manufacturer Part Number 40A15
Installation Instructions
J. Douglas from Grass Valley, CA
Broken plastic parts
Cleaned the refrigerator as the old parts were removed. Installed new parts as the old parts were removed so as to easily identify the replacement parts. Very easy and wife was extremely happy after old plastic parts self destructed over a period of months and refrigerator was essentially unusable on the bottom two drawers.
Read more...
Your Price
$38.15
Temperature Sensor
PartSelect Number PS820208
Manufacturer Part Number 316217002
The oven temperature sensor for your range may also be called a probe. The quick connect on this part may differ than your original piece. If the temperature sensor does not fit you will have to cut off the quick connect, and then wire together with porcelain wire nuts. The function of the oven temperature sensor is to measure the temperature in the oven and signal the other heating components. Before you begin this repair make sure to disconnect the power to the range. The tools required for this installation include a number two Phillips screwdriver or a number two square head screwdriver, and maybe a pair of wire strippers and crimpers.
Fixes these symptoms
- Element will not heat
- Little to no heat when baking
- Oven is too hot
- See more...
Installation Instructions
Dan from Bellevue, ID
Oven not heating to desired temperature
Replaced clock control by removing surface burner control knobs and plastic nuts, and then the cover over the oven control. Two screw hold the clock in place, after removal and disconnecting the plug-in you can reinstall the new clock control. The Heat Sensor inside the oven will also need to be replaced. It is located inside the oven and attached with two screws; the back of the oven will need to be removed to unplug. Reverse removal procedure and turn the power back on to the stove.
Read more...
Your Price
$12.19
Oven Light Bulb
PartSelect Number PS12751166
Manufacturer Part Number 316538904
Clear, 120 Volt, 40 Watt.
Installation Instructions
Colin from Hollis, NY
Ice-Maker and Water Dispenser not working.
First I disconnected the power cord, then removed the screws that held the bracket that holds the base for the water-filer in place. I then disconnected the water lines(intake and outflow). Next I removed the screws that held the water-filter's base in place. I then disconnected the release lock mechanism for the filter and finally removed the water-filter base. I did the reverse to install the new water-filter base. Previously I had tested the intake water line and noticed the water was flowing with enough pressure upto the water-filter's base but no water was exiting thru the outflow line, which leads to the Ice-Maker and Dispenser. I had tried changing the filter but that didn't solve the problem it was then I had realized that the Base was the problem. The actual problem was the spring-loaded valves for both the intake and outflow lines, which had a plastic prong that protrudes out of the base that is triggered by the filter when installed. The two prongs were worn-down so the filter wasn't activating the spring-loaded release valve to let the water thru. As for the light, I just unscrewed it.
Read more...
Your Price
$7.32
Light Bulb - 40W
PartSelect Number PS884734
Manufacturer Part Number 8009
This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these replacement bulbs are most often used to light the inside of refrigerators and ranges. It features a standard socket base, which means you simply unscrew the burnt-out bulb and screw in the replacement. Depending on the appliance you may require a screwdriver or nut driver to access the light bulb. We recommend you wear work gloves while handling this replacement part. It is constructed of glass and metal and is sold individually. Depending on the appliance and location of the bulb within it, you may want to consider disconnecting power and using a flashlight for easier access to unscrewing and re-screwing in your bulb during this repair.
Installation Instructions
judie from mays landing, NJ
interior drawers were off their rollers
pulled the washer out and replaces the top roller system on both sides and the replaced the weels and brackets on the bottom drwaer. however i had trouble putting the dish washer back correctly and had to call a repairman to adjust the dishwasher and alighn it to open and close properly. but i did do good inside. i feel it was easy and a success. thank you for having the supplies for us to attempt to repair it on our own.
Read more...
Your Price
$8.41
Main Terminal Block Kit
PartSelect Number PS471605
Manufacturer Part Number 5304409888
Terminal block kits are also known as terminal boards, or terminal strips, and they are found in a wide variety of household appliances. Most often in ranges, wall ovens, and dryers. This kit attaches the power cord to the inner wiring of your appliance. If the terminal block is faulty, your appliance will not get the power it needs to operate properly. When removing the old block pay close attention to the wire placement, this will make installing your new part much easier. If you notice any of the wires or wire terminals are corroded or damaged they will also need to be replaced.
Fixes these symptoms
- Element will not heat
- Little to no heat when baking
- Little to no heat when broiling
- See more...
Installation Instructions
Timothy from Spring Valley, AL
Cord was not tightened enough by delivery crew.
PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools needed are phillips screwdriver, deep socket for lug nuts. Nut driver optional. Hope this is helpful.
Read more...
Your Price
$8.22
Single Heating Element Support Clip
I had noticed that the former element was sagging at the front end. I installed the additional clips (not original) on each forward end of the element for additional support. Read more...
PartSelect Number PS243701
Manufacturer Part Number WB2X9719
The metallic clip, or also known as a broil element support, is for a oven element on a range. This part holds the broil element in place on top of the oven. If your support clip is broken then this replacement should be the solution. The tools needed for this project are slip joint pliers. For safety precautions, make sure to unplug your range from the power source, or shut off the house circuit breaker before starting this project. Refer to the installation instructions for best results and accuracy.
Fixes these symptoms
- Element will not heat
- See more...
Installation Instructions
Paul from Canton, NY
broiling element had burned through, req. its replacement
First I removed the two screws that hold the element in place. I also removed a screw that held one end of a support bracket. I then pulled the element out about 3 inches and disconnected the two wires. Reversing these steps, I finished the element's replacement.I had noticed that the former element was sagging at the front end. I installed the additional clips (not original) on each forward end of the element for additional support. Read more...
Your Price
$35.00
Light Bulb Lens
PartSelect Number PS2349721
Manufacturer Part Number 318406100
The Frigidaire light bulb lens covers the interior light bulb in an oven. No tools are necessary to replace this item. After unplugging the appliance, slide off the wire bracket to remove the existing light bulb lens. Be sure to remove all broken glass, if applicable, before installing the new lens. It is recommended to check the state of the light bulb while the lens is off. This part is made of glass. The lens is a genuine Frigidaire part, sourced directly from the manufacturer, and is sold individually.
Installation Instructions
Jim from Harrison, MI
Lower baking element would not heat up.
Your online instructions said to remove the two screws and pull out the heating element about 3 inches and disconnect. When I did this the element came out but not where it was connect to the wire., I could not locate the wire from the front of the oven. I then pulled out the oven from the built in cabinet and removed the rear panel. Then inserted the element with the 2 screws from the front and connect the wires to the element from the back of the oven. Jim
Read more...
Your Price
$12.57
Drip Bowl - 6 Inch
PartSelect Number PS244697
Manufacturer Part Number WB32X107
The drip bowl on your range is designed to catch any spills that may occur when cooking. This drip bowl is chrome in color and is 6 inches in diameter. The chrome drip bowl is intended for use with rolled, terminal-style plug-in surface element units. The drip bowl is located beneath the surface element, so you will need to remove the element prior to swapping out the old drip bowl for a new one. Many of our customers have rated this repair as easy, and you will not require any tools to complete it. This part is sold individually.
Installation Instructions
Gregory from Princeton Junction, NJ
Control switch did not function and one burner worked only occasionally
First, I used the PatrSelect website, which has great prices, and has helpful diagrams. Once I had all the parts, I worked with my wife to turn off the power at our home junction box. Next, I lifted off the cover over the control area of this range. I removed four nuts to lift out the panel that holds the four controls and the fan switch. I removed the wires from the broken controls, removed the two screws holding each control in place, then screwed the new ones in place. I would recommend trimming the posts on the controls to the correct size before screwing them in place, because it is easier to grip them and not bend them when they are not mounted. I reconnected the wires and replaced the panel. For the "receptacle", I followed the instructions provided regarding cutting the wire and placing the wire nut and heat shrink tubing. I opened the unit that houses the burners to get easy access.
Read more...
Your Price
$28.72
Temperature Sensor
PartSelect Number PS11758156
Manufacturer Part Number 5304504897
Fixes these symptoms
- Element will not heat
- Little to no heat when baking
- Oven is too hot
- See more...
Installation Instructions
Alexander from DELMAR, NY
Both oven bake and broil elements lost power suddenly at the same time.
Installation of the temparature sensor, one of the technician recommended parts took no time, just two screws and a snap off/snap on part. It did not fix the problem. I then replaced the main control panel, which requires more work, but didn't solce the ussue either. I then replaced the thermal fuse, which wasn't mentioned by tech support, and required much more disassebly of the top panels of the stove, with still no fix to the problem. I am waiting to replace the thermostat heat sensor unit, the only other part in the circuit controlling power supply, requiring removal of the stove top again,
Read more...
Your Price
$21.43
Drip Bowl - 8 Inch
PartSelect Number PS244696
Manufacturer Part Number WB32X106
Drip bowls are located under the heating elements and catch grease and spills that come from cooking on your stove top. If your drip bowl is damaged or rusted, it could allow grease to drip inside your range. This 8 inch chrome drip bowl fits most electric ranges. Before you replace your damaged drip bowl, make sure the element is turned off and cool to the touch. Installation is easy, just remove the element, replace the current drip bowl, and reattach the element. Make sure the small hole on the bowl lines up with the element socket. Drip bowls are sold separately.
Fixes these symptoms
- Element will not heat
- See more...
Installation Instructions
Gregory from Princeton Junction, NJ
Control switch did not function and one burner worked only occasionally
First, I used the PatrSelect website, which has great prices, and has helpful diagrams. Once I had all the parts, I worked with my wife to turn off the power at our home junction box. Next, I lifted off the cover over the control area of this range. I removed four nuts to lift out the panel that holds the four controls and the fan switch. I removed the wires from the broken controls, removed the two screws holding each control in place, then screwed the new ones in place. I would recommend trimming the posts on the controls to the correct size before screwing them in place, because it is easier to grip them and not bend them when they are not mounted. I reconnected the wires and replaced the panel. For the "receptacle", I followed the instructions provided regarding cutting the wire and placing the wire nut and heat shrink tubing. I opened the unit that houses the burners to get easy access.
Read more...
Appliance Type
Popular Kenmore Stove Models
Below are the most popular Kenmore Stove models we have. Enter your model number in the search box to find your model.
- 79048833901 WALLOVEN
- 79048783901 WALLOVEN
- 79048789901 WALLOVEN
- 79048839901 WALLOVEN
- 79047839400
- 79047833400
- 79046352400
- 79099503990
- 91141089991
- 9114742996
- 91140495890
- 79048832901 WALLOVEN
- 79048833900 WALLOVEN
- 79046703606
- 79046823100
- 9114088816
- 9114288816
- 79048763900 WALLOVEN
- 79040529400 ELECTRIC WALL OVEN
- 79049443412 WALL OVEN
