My Orders
Inglis Range Valves
GET YOUR OFFICIAL Inglis PARTS TO ENSURE VICTORY
Popular Inglis Range Valves
This is the Right Rear Burner Head.
This is the Right Rear Burner Head.
Installation Instructions
Charles from ATLANTA, GA
REPLACING burner head and ignitor
Remove the screw on the front of each side, also there are two screws holding the burner controls. Remove the burner knobs. There are two screws holding the burner head to the top of the burner panel, looking down on the burner head, these will not come out easily. Here's where the drill comes in. Drill the two screws head off, there are
... Read more
two gas line connections that must be removed, be careful not to twist the gas line. Remove the burner head and replace with the new one. When replacing the burner head, screw the gas line to the burner head first, then to the main gas control.
Read less
This part distributes flame evenly to your cookware.
This part distributes flame evenly to your cookware.
Installation Instructions
Charles from ATLANTA, GA
REPLACING burner head and ignitor
Remove the screw on the front of each side, also there are two screws holding the burner controls. Remove the burner knobs. There are two screws holding the burner head to the top of the burner panel, looking down on the burner head, these will not come out easily. Here's where the drill comes in. Drill the two screws head off, there are
... Read more
two gas line connections that must be removed, be careful not to twist the gas line. Remove the burner head and replace with the new one. When replacing the burner head, screw the gas line to the burner head first, then to the main gas control.
Read less
This electronic burner box forms the main housing that supports and holds the surface heating elements under an electric cooktop. It keeps the elements stable, level, and properly aligned so they heat evenly during cooking. This replacement is useful when the original housing becomes bent, corroded, or damaged, or when elements begin to sag, rattle, or sit unevenly. Measuring roughly 25 inches by 34 inches by 3 inches, it is designed to match the original fit, and installation typically involves removing the cooktop surface and transferring the elements into the new box to restore solid, reliable support.
This electronic burner box forms the main housing that supports and holds the surface heating elements under an electric cooktop. It keeps the elements stable, level, and properly aligned so they heat evenly during cooking. This replacement is useful when the original housing becomes bent, corroded, or damaged, or when elements begin to sag, rattle, or sit unevenly. Measuring roughly 25 inches by 34 inches by 3 inches, it is designed to match the original fit, and installation typically involves removing the cooktop surface and transferring the elements into the new box to restore solid, reliable support.
This part distributes flame evenly to your cookware.
This part distributes flame evenly to your cookware.
Installation Instructions
Charles from ATLANTA, GA
REPLACING burner head and ignitor
Remove the screw on the front of each side, also there are two screws holding the burner controls. Remove the burner knobs. There are two screws holding the burner head to the top of the burner panel, looking down on the burner head, these will not come out easily. Here's where the drill comes in. Drill the two screws head off, there are
... Read more
two gas line connections that must be removed, be careful not to twist the gas line. Remove the burner head and replace with the new one. When replacing the burner head, screw the gas line to the burner head first, then to the main gas control.
Read less
Burner valves are attached to the main gas line. When the switch is turned the gas then flows into a tube that mixes with air, creating the appropriate mixture for combustion.
Burner valves are attached to the main gas line. When the switch is turned the gas then flows into a tube that mixes with air, creating the appropriate mixture for combustion.
MAKE THIS REPAIR A GUARANTEED WIN
OVER 2 MILLION PARTS TO ENSURE VICTORY
Introducing the Oven Safety Valve and Pressure Regulator from the esteemed brand, Whirlpool. This genuine OEM part stands out as an essential component, assembled with a natural gas bake orifice. Its primary function is to maintain the steady flow of gas, thereby controlling the sear and simmer levels in your oven. Before installation, remember to disconnect any electricity and shut down the gas in order to maintain safety. For aid in cooking like a pro, trust none but the Whirlpool Oven Safety Valve and Pressure Regulator. Please verify compatibility with your model at the time of your order.
Introducing the Oven Safety Valve and Pressure Regulator from the esteemed brand, Whirlpool. This genuine OEM part stands out as an essential component, assembled with a natural gas bake orifice. Its primary function is to maintain the steady flow of gas, thereby controlling the sear and simmer levels in your oven. Before installation, remember to disconnect any electricity and shut down the gas in order to maintain safety. For aid in cooking like a pro, trust none but the Whirlpool Oven Safety Valve and Pressure Regulator. Please verify compatibility with your model at the time of your order.
Sold individually.
Sold individually.
Installation Instructions
Joseph from Matawan, NJ
needed to replace the main top of stove
First I removes all visible screws. The stove top would not budge. I noticed that the elements had screws holding the top in place. These were difficult to remove and all eight screw broke. I then removed the top. I had to remove the broken screws by drilling them out and re-tapping the threads. This was the single most difficult thing to
... Read more
do and took the most time. Once this was complete, re-installing the top was quite simple.
Haviong directions would have been very helpful.
Haviong directions would have been very helpful.
Read less
This converts from Natural Gas (NG) to Liquid Propane (LP)
This converts from Natural Gas (NG) to Liquid Propane (LP)
Sold individually.
Sold individually.
Introducing the genuine Burner Valve from Whirlpool. This OEM part designed for sustained peak performance, is compatible with several models of Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef. Serving dual functionality, this Surface Burner Valve can be fitted in Left Rear, Left Front, or Right Front, depending on your model specifications. This essential maintenance item adjusts and controls the flow of gas to your range's surface burner, contributing to your appliance's optimal efficiency. Before fitting this part, remember to unplug the range and turn off gas supply for safety. Protect your hands with work gloves during installation.
Introducing the genuine Burner Valve from Whirlpool. This OEM part designed for sustained peak performance, is compatible with several models of Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef. Serving dual functionality, this Surface Burner Valve can be fitted in Left Rear, Left Front, or Right Front, depending on your model specifications. This essential maintenance item adjusts and controls the flow of gas to your range's surface burner, contributing to your appliance's optimal efficiency. Before fitting this part, remember to unplug the range and turn off gas supply for safety. Protect your hands with work gloves during installation.
Installation Instructions
Douglas from BETTENDORF, IA
Valve stem broke off the right control burner valve so the knob for burner could not go on the stem to light the burner.
I first shut off gas to stove and unplugged the stove. I then opened the oven door and used a phillips screw driver to remove the three screws under the cover plate that sits behind the gas control knobs . I then removed the cover plate. I then took off the grates on stove top and proceeded to remove the two screws on each burner head wi
... Read more
th a phililps screwdriver. Some where tight so I used a drill driver on low speed to turn the screws out. After removing the burner heads I had to remove two screws on each corner in the front under the cook top of the stove to remove the cook top off the stove. But before that I had to release the two wires from a clip under the cook top for the ignitor switches before I could lift the cook top off the stove. These should be on the right hand side. Now I had access to remove the burner valve that had the broken stem that the knob is attached too. For this I used adjustable wrench to remove the nut for the gas tube that goes from the burner head to the control valve. Then I had to release the ignitor switch by pulling it off the control valve stem or gently pry it off with a flat head screw driver. Then used 1/4 in socket wrench to remove the top bolt to release the old burner valve off the gas plenum where all the burner valves are attached too. Then pull the old control valve off from underneath the gas plenum. Then i put in the new burner valve making sure it had a rubber seal around it where it goes up through the hole underneath the gas plenum. Then while holding control valve in place put the screw back in the top of the gas plenum through the other hole on top of the gas plenum and screw it in the burner valve making sure it also has a seal under the bottom of head of the bolt that you are screwing in to the control valve. This is so that no gas can leak from the plenum where the control valve is attached to. The control valve threads should be lined up with the bolt since both holes on the bottom and top of the gas rail (plenum) are lined up Use a 1/4 in socket to tighten down the bolt with the seal but don't over tighten. Then reattach the tube that goes from the burner head to the control valve with adjustable wrench and make sure not to over tighten. Then grab the stove cook top that you took off and replace it back on top of stove.After in place make sure to put those two wires back into clip that is under the cook top so wires are not touching the oven. You have to put part of your arm under the cook top and use your hand to try to push the wires back into the clip that's under the stove top. These wires will be on the right hand side. This is kinds tricky to do. Then tighten cook top back down with two screws and reattach the ignitor switch back through the valve stem of new control valve . It should clip in around the valve stem. Then reattach the cover plate over the valves stems with the remaining three screws and attach the control knobs.
Read less