My Orders
Hotpoint Dryer Switches
GET YOUR OFFICIAL Hotpoint PARTS TO ENSURE VICTORY
Popular Hotpoint Dryer Switches
Restore reliable operation to your GE dryer with this genuine OEM push-to-start switch, designed specifically for use with a range of GE dryer models. This switch activates the dryer when you press and release the button, making it an essential component for proper startup.
Common signs that this part may need replacement include the dryer failing to start or starting unexpectedly without pressing the switch. Replacing the switch is a straightforward repair and requires only a Phillips screwdriver and a flathead screwdriver. Before beginning the installation, always disconnect the power to ensure safety. Once the power is off, remove the control panel screws, disconnect the old switch, and install the new one in its place.
This part is sold individually and is a reliable solution for restoring your dryer's functionality with minimal effort.
Restore reliable operation to your GE dryer with this genuine OEM push-to-start switch, designed specifically for use with a range of GE dryer models. This switch activates the dryer when you press and release the button, making it an essential component for proper startup.
Common signs that this part may need replacement include the dryer failing to start or starting unexpectedly without pressing the switch. Replacing the switch is a straightforward repair and requires only a Phillips screwdriver and a flathead screwdriver. Before beginning the installation, always disconnect the power to ensure safety. Once the power is off, remove the control panel screws, disconnect the old switch, and install the new one in its place.
This part is sold individually and is a reliable solution for restoring your dryer's functionality with minimal effort.
Installation Instructions
Gary from LAVALLETTE, NJ
replaced start button and start switch
disconnect power plug unscrew 3 screws in back. lean forward remove button disconnect 2 wires in back of switch. put switch connect 2 wires and button. connect 3 screws in the back. ready to start working
This is the door switch for your dryer. Door switches are used to communicate with the control board when the door is fully closed, so the drying cycle can safely begin, and if it is opened so it can stop. If this door switch is damaged or bad from extended use or excessive force when closing, it will cause your dryer not to start, and it will need to be replaced. This door switch will require a few tools, such as a screwdriver, wrench, and pliers to replace, and some slight disassembly of your dryer. This door switch is an OEM part and is sold individually.
This is the door switch for your dryer. Door switches are used to communicate with the control board when the door is fully closed, so the drying cycle can safely begin, and if it is opened so it can stop. If this door switch is damaged or bad from extended use or excessive force when closing, it will cause your dryer not to start, and it will need to be replaced. This door switch will require a few tools, such as a screwdriver, wrench, and pliers to replace, and some slight disassembly of your dryer. This door switch is an OEM part and is sold individually.
Installation Instructions
Kenneth from COATESVILLE, PA
Dryer would not start
I popped the door switch out with a small screwdriver, disconnected the electrical connection and re-connected the new switch and popped the new switch in place with a little adjustment.
This replacement start switch is a genuine OEM part for your dryer. If your dryer will not start or shut off, you may need to replace this part. For this repair you will need a number 2 Phillips screwdriver and a pair of needle nose pliers. Disconnect power to the dryer before beginning this repair.
This replacement start switch is a genuine OEM part for your dryer. If your dryer will not start or shut off, you may need to replace this part. For this repair you will need a number 2 Phillips screwdriver and a pair of needle nose pliers. Disconnect power to the dryer before beginning this repair.
Installation Instructions
Mr Dennis from Twinsburg, OH
Knob would not engage, had to manually turn outer ring to start washer.
Used a screw driver and needle nose pliers to remove clip from behind the timer knob. Took 2 minutes to remove clip, i admit it was a little tricky but once you get a grip on the clip very easily removed. Replaced with new knob, old knob gear was completley stripped . put the new clip on and presto, Like brand new.A normal service call wo
... Read more
uld of ran me 45.00 just to tell me what was wrong with the machine.
Read less
A door switch is a simple on/off mechanism that prohibits the dryer from operating when the door is open.
A door switch is a simple on/off mechanism that prohibits the dryer from operating when the door is open.
Installation Instructions
Joshua from Dallas, TX
Dryer would not start
The end repair was very simple and took minimal effort. The time and difficulty was all in the testing. I disassembled the dryer and removed the drum and then hard wired each thermo-fuse to determine where the fault was. After test all of those I was stumped. When I opened the door the light would not come on so I assumed it was a pow
... Read more
er fault closer to the source. However after all of my testing I couldn't find anything wrong. I then removed the light bulb and realized it was burned out which led me to the door switch being the fault. I removed the switch and soldered the three wire together and the dryer started right up! All I had to do was order a new $15 part, unsolder the wires and plug them in. Would have been so much simpler if that light bulb hadn't of been burned out causing me to over think my diagnosis. This was my first major appliance repair and I did it with only the help of the parts diagram provided on the website.
Read less
The interlock switch may also be referred to as a belt switch. This part is a simple on/off mechanism that prohibits the appliance from operating when the door is open. This is a part for your dryer. The interlock switch senses the door is shut and the dryer can begin. This part might need to be replaced if your dryer is not starting or is in process while the door is open. The black rectangular part of the switch is approximately 2 inches long and a 1/2-inch wide with two gold plates on either end. This is a genuine OEM part that is sourced right from the manufacturer.
The interlock switch may also be referred to as a belt switch. This part is a simple on/off mechanism that prohibits the appliance from operating when the door is open. This is a part for your dryer. The interlock switch senses the door is shut and the dryer can begin. This part might need to be replaced if your dryer is not starting or is in process while the door is open. The black rectangular part of the switch is approximately 2 inches long and a 1/2-inch wide with two gold plates on either end. This is a genuine OEM part that is sourced right from the manufacturer.
Installation Instructions
Steven from EPHRATA, WA
interlock switch was bad. Prevents the dishwasher form running as it "thinks" the door is still open.
Opened door, removed screw holding down metal plate that presses against interlock switch when door is closed. Removed plastic cover thingy that is over interlock switches. Removed the interlock switch by pressing the plastic lock thingy away from switch. Pulled the wires off each end of the interlock switch. Removed new interlock switch
... Read more
from plastic bag and reversed above procedure. Done, shut door and the dishwasher works.
Read less
MAKE THIS REPAIR A GUARANTEED WIN
OVER 2 MILLION PARTS TO ENSURE VICTORY
This part is used to start the dryer once you have selected a setting on the timer.
This part is used to start the dryer once you have selected a setting on the timer.
Installation Instructions
Jaren from Lemoore, CA
Broken Knob Post
First I unplugged the dryer, then I removed the access panel on the back of the control panel. I removed the wires from the back of the switch...Here is where I messed up. I removed the switch prior to ordering the part, the bad part is the way I removed the part. When you get the new part in you will be able to see how it will be mounted
... Read more
to the control panel. I had no idea, so I did what was necessary to remove it. Needless to say, I bent the hell out of the hole that the switch mounts in. In turn, the installation of the new switch did not go as easily as I would have liked. After straightening out some metal and drowning the thing in epoxy, the new switch is installed. I hooked the wires back up on the back of the switch, plug in the dryer, and dry some clothes. Standing victorious over the dryer with beer in hand, not only did I accomplish the mission but I learned my lesson... destructive removal = BAD!
Read less
Introduce convenience and quality to your appliance repairs with this GE SWITCH ROTARY. This durable and efficient part will help your appliances function at their best, offering an improved performance and longevity. This SWITCH ROTARY from GE is uniquely designed for compatibility with specific machines, ensuring a seamless fit and flawless functionality. Crafted from premium materials, this component offers resilient functionality over time. Trust the superior quality of GE for your appliance repair needs and keep your machines running smoothly and effectively. Your appliances deserve the best, and this SWITCH ROTARY offers just that.
Introduce convenience and quality to your appliance repairs with this GE SWITCH ROTARY. This durable and efficient part will help your appliances function at their best, offering an improved performance and longevity. This SWITCH ROTARY from GE is uniquely designed for compatibility with specific machines, ensuring a seamless fit and flawless functionality. Crafted from premium materials, this component offers resilient functionality over time. Trust the superior quality of GE for your appliance repair needs and keep your machines running smoothly and effectively. Your appliances deserve the best, and this SWITCH ROTARY offers just that.
