Hoover Refrigerator Hardware
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Hoover Refrigerator Hardware
Your Price
$7.47
In Stock
Hoover Refrigerator Screw
PartSelect Number PS11743743
Manufacturer Part Number WP681249
Sold individually.
Your Price
$7.47
In Stock
Hoover Refrigerator Washer Hose Clamp
PartSelect Number PS11743008
Manufacturer Part Number WP596669
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This clamp is used to securely attach a hose to another part of your appliance, which helps prevent leaks from those connections. Depending on the appliance, it can attach hoses to drain pumps, water inlet valves, pressure switches, and injector nozzles. We recommend you refer to model-specific diagrams for appropriate uses and exact placement. This hose clamp is made of metal, and is sold individually. To access and replace this part you will need a nut driver, pliers, and screwdrivers. Before you begin any repair work, make sure you have unplugged your appliance, and shut off the water supply if applicable.
Fixes these symptoms
- Leaking
- See more...
Installation Instructions
jeff from lindenhurst, IL
Washing Machine was leaking water
Loosened the hose clamp, removed the injector valve and injector nozzle assembly, replaced both and tightened with new hose clamp. Fixed the problem for less than $20!! Washing machine is 20 years old and this was the first problem--hopefully it is now good for another 20 years!
Read more...
Your Price
$9.62
In Stock
Hoover Refrigerator Hose Clamp
PartSelect Number PS11740613
Manufacturer Part Number WP285655
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installation, you will need a flat head screw driver to replace the clamp and a drill to access the screws to remove the front of the washer. Be careful if you do not have specific clamp pliers as the clamp could fly off. Once the front of the washer has been removed, take a quick look for water damage or any obvious signs of where the leak is coming from. If it is not obvious, run water to test.
Fixes these symptoms
- Leaking
- Will not drain
- See more...
Installation Instructions
Stephen from Laveen, AZ
Drive Pump Leaked
It took some trial and error but overall not a difficult project. 1. Take the front covers off. 2. Undo the pully spring to loosen belt 3. Remove belt off idler pulley wheel and free up belt from the large wheel. 4. Disconect the wiring harness and the hoses. 5. Undo the motor mounting bolts (4) 6. Take motor out of washer and remove the 3 screws holding the pump to the motor. 7. The pump had melted to the shaft and required I chisel the pump off of the shaft. 8. Attach new pump paying attention to where the belt is positioned. 9. Reattach the motor bolts, hoses, and wiring harnes. 10. Attach the belt and test the pump. 11. Put the front back on.
Read more...
Your Price
$7.47
In Stock
Hoover Refrigerator Screw
PartSelect Number PS11742721
Manufacturer Part Number WP488729
Metallic screw that is less than an inch long. Does not include the plastic washer.
Installation Instructions
Kyle from Wimauma, FL
Black Cam was bren on lower door hinge
This was a very simple job. Remove the top Hinge bracket, a total of 4 screws, lifted the door off the bottom hinge, removed the bottom hinge set up, 2 screws, replaced it, and attached the new bottom black door cam, lifted the door back onto the bottom hinge and aligned the top hinge, and reinserted the screws, and Ta Da, The door works like a new refrigerator door. 15 to 30 min tops. I did not even have to take the refrigerator items out of there door holder.
Read more...
Your Price
$12.20
In Stock
Hoover Refrigerator Screw
PartSelect Number PS11742240
Manufacturer Part Number WP400021-1
Sold individually.
Fixes these symptoms
- Gas igniter glows, but will not light
- Will Not Start
- See more...
Installation Instructions
Gayle from COUPEVILLE, WA
Replacing burning assemblies and rusted screws
Installing the 2 new burner assemblies worked great with the new screws. New screws however, did not work with the old burner assemblies that have rusted screws I wanted to replace. New burner assemblies are slightly taller that the old ones.
Read more...
Your Price
$7.47
In Stock
Hoover Refrigerator Screw
PartSelect Number PS11742754
Manufacturer Part Number WP489478
Sold individually.
Installation Instructions
Michael from Torrance, CA
lower left shelf support was broken
I removed all contents from the lower shelf. I, then removed both of the pull out drawers. Secondly, I removed the lower glass shelf and the glass support tray. At this point all four plastic shelf supports were accessible. I removed the inner screw from all four supports and replaced with four new shelf supports. Then reassembled in reverse order. Very easy to do!
Read more...
Your Price
$7.47
In Stock
Hoover Refrigerator Dishwasher Screw
PartSelect Number PS11753384
Manufacturer Part Number WPW10348409
Sold individually.
Fixes these symptoms
- Door latch failure
- See more...
Installation Instructions
REBECCA from GREENFIELD TWP., PA
My son broke the door handle off the Refrigerator
I removed two screws that were holding on broken handle. I put new handle in place and attached it with new screws. Ordering parts on line and receving them in mail a few days later was awsome. I did not need my husbands help at all .
Read more...
Your Price
$7.47
In Stock
Hoover Refrigerator Screw
PartSelect Number PS11747542
Manufacturer Part Number WP98165
This screw is a little under an inch long and is made of metal. It is used with a refrigerator's ice maker assembly. Sold individually.
Installation Instructions
Lynn H from MILL CREEK, WA
Hinge pin for drawer lid broke
1. Remove all drawers {3}, shelves {glass 1}, shelf support {1}. 2. Remove two {2} screws from End Cap. 3. Carefully remove End Cap and drawer temperature control part on the back wall keeping them aligned as installed. The part on the back wall swings out so that the tab on the left end of the piece may be withdrawn from the securing slot (hole). The two parts should be carefully removed while keeping the two parts at a right angle the way they are installed. The reason for this caution follows. 4. On the back side of both parts are plastic pieces that, I believe, can be easily broken if you are not aware. The pieces are connected together at the right angle. They are the control arms for the temperature control -- on right side End Cap only -- the left side doesn't have them or the rear part on the back wall. 5. The pieces must be disconnected and removed. You must examine and ponder how they are held in place and hooked together in order to disconnect and remove them without damaging them. The same advice is applicable to reinstalling the pieces in the new part -- End Cap. 6. After reassembled and keeping the two parts at a right angle, insert the tab on the left end of the back wall part into the slot (hole) and swing the two parts back into position. 7. Replace the screws. 8. Done, reinstall the shelf, shelf support, and the drawers. NOTE: I ordered the two screws but they were not needed.
Read more...
Your Price
$7.47
In Stock
Hoover Refrigerator Appliance Screw
The burner unit slides out easily and after unscrewing the sides, you have to disconnect the wires from the underside of the igniters. The venturi tubes and igniters then unscrew from the underside of the burners which twist right out of the assembly. Re-Assembly is very intuitive looking at it and it all goes right back together as it came out. Took 45 minutes total and that includes fighting with some screws that had rusted onto the burner.
Reading some of the previous reviews, current prices are double to triple what other people did the repair for leading me to believe parts won't be available for much longer. Make the repair while you still can! Read more...
PartSelect Number PS11743002
Manufacturer Part Number WP59002061
Sold individually.
Installation Instructions
John from WAKEFIELD, MA
Flames appeared outside of burners
The front burner had a noticible flame coming from the base, so I originally purchased a single burner to replace it (you could see a corroded hole at the bottom). Upon taking the unit apart, I noticed the corrosion was much worse than met the eye. Given the age of the unit and that some parts were already becoming discontinued I decided to gut the whole thing and replace it all.The burner unit slides out easily and after unscrewing the sides, you have to disconnect the wires from the underside of the igniters. The venturi tubes and igniters then unscrew from the underside of the burners which twist right out of the assembly. Re-Assembly is very intuitive looking at it and it all goes right back together as it came out. Took 45 minutes total and that includes fighting with some screws that had rusted onto the burner.
Reading some of the previous reviews, current prices are double to triple what other people did the repair for leading me to believe parts won't be available for much longer. Make the repair while you still can! Read more...
Your Price
$9.62
In Stock
Hoover Refrigerator Screw
Worked great! Read more...
PartSelect Number PS11745622
Manufacturer Part Number WP8281196
Sold individually.
Installation Instructions
Carol from Monroe, NY
Refrig making a lot of noise
The motor kit had only two wires coming out of it. The existing one in the refrig had 6. I spliced the 2 red to one black on the new part and 2 white to the other black wire on the new part. The two green I attached to a screw. I left the 6 wire harness in place just cut off the plug piece that went into the old motor, and spliced all my wires. Worked great! Read more...