Engine Bearings

This Ball Bearing is an individually sold, silver/black, metal part. It reduces friction in the spindle assembly between the spindle shaft and the spindle housing. If broken due to wear/fatigue, you will hear a grinding, growling, rumbling or screeching sound, and should replace the part. Refer to your make, model and diagrams to ensure this is the right part for you.

This OEM-manufactured flange bearing supports and enables the smooth rotation of parts in your lawn equipment, such as the blade assembly, axle assembly, or steering components. This bearing has an inner diameter of .76 inches, an outer diameter of .941 inches, and a width of 1 inch. It is made of plastic. A similar similar style flange bearing can be used at the bottom of the crank, but it would be made of metal. When the bearing is broken, you may notice signs of wear and abnormal squealing noises coming from your machine. If neglected, the parts the bearing is supporting can overheat and potentially seize up. To switch out a flange bearing, you need to take off any bolts, screws, or clips that are holding it in place. Using a hammer or a bearing puller tool, gently push the bearing out of its housing. Since this part is sold individually, remember to refer to your user manual to understand how many bearings your machine will need. It is strongly recommended that you replace all the bearings in one go, as they wear out at the same rate.

This manufacturer-supplied replacement part is designed for use with Kohler engines commonly installed on lawn and garden equipment. The bushing helps to secure the throttle linkage. It provides an identical replacement for a missing or a faulty hardware that was installed on a new unit. Please refer to the appropriate diagrams of your model for the exact location and the correct installation of this part. Keep in mind this high-quality bushing is made of durable plastic and is sold individually. You will need a wrench set to remove the housing in order to gain access to the bushing.

This is a genuine replacement part produced by original manufacturer. It is used in various tractors from MTD, Yard Machines, Bolens, and Yard Man. Flange bearings facilitate spinning axles/shafts and reduce friction. They are a very high wear item that may require replacement often. Sold individually.

This is a genuine OEM sourced replacement part that is intended to be used with lawnmowers, snowthrowers, and tillers from Bolens, Ryobi, Yard Machines, MTD, Troy-Bilt, and Yard-Man. The sealed bearing is used to limit friction between a rotating shaft and a fixed part assembly. It is recommended to review your models illustrated part diagram to confirm the bearing\\\'s compatibility. This item is sold as an individual replacement part.

This single-row, deep-groove ball bearing is sized at 12x32x10mm and is made of durable metal. It is used to reduce friction and vibrations when it is in between two parts that are rotating or moving against each other. This bearing can handle forces that are applied to it up-and-down and sideways, also known as radial and axial loads. It is easy to install and can handle high rotational speeds without causing too much vibration or making much noise. Over time, this ball bearing wears out from heat and pressure and starts to fail. If the engine of your machine has been run without oil in the gas tank, this ball bearing can seize. In these situations, you will need to replace the ball bearings. Otherwise, you will notice that your machine overheats, works harder because of the increased friction it is handling, and produces excessive vibration and noise. To extract a ball bearing from your machine, you will need to insert a flat-head screwdriver through the bearing opening and against the seal. Then, tap the seal out with a mallet. Afterwards, slot a socket through the diameter of the bearing, and tap the entire bearing out of its place by again using a mallet. This authentic OEM part is sold individually, so be sure to refer to your user manual to verify how many bearings your machine needs and where they are in it.

This is an authentic manufacturer sourced replacement part designed for use with Toro walk-behind lawn mowers. This part helps to secure the mower wheel, allowing it to rotate freely. It is made out of metal and it is sold individually. To replace this part you would need a wrench and pliers.

This is a genuine replacement part for tractors made by Snapper, Murray, and Simplicity. The bushing fits between the washer and the mounting steering plate. It is made out of plastic and will need to be replaced if it becomes broken. A screwdriver, a set of pliers, and a wrench set may all be needed to help replace this part. This item is sold individually.

This is an authentic Toro replacement part manufactured for use with lawn tractors. The special insulator bushing is used to seal the fitting between the fuel valve and the fuel tank and to prevent damage to either part. This bushing is available as an individual replacement part, please see model diagram for associative parts.