My Orders
Electrolux Freezer Compressors
GET YOUR OFFICIAL Electrolux PARTS TO ENSURE VICTORY
Popular Electrolux Freezer Compressors
The start relay briefly boosts the compressor, and then shuts off as soon as the motor gets up to speed.
Note: This part has been updated by the manufacturer. It may differ in appearance but will still function the same as the original.
The start relay briefly boosts the compressor, and then shuts off as soon as the motor gets up to speed.
Note: This part has been updated by the manufacturer. It may differ in appearance but will still function the same as the original.
Installation Instructions
Reynaldo from SAN BRUNO, CA
there is electrical surge from Pacific Gas and electric.
There is PG and E employee working in one of the electrical post that cause the electric surging,there is a 3 big bang then we smell burning wire.it blew and burned the compressor relay,so what i did is figure it out, all 2 refregirator fan is running the heater is working,but its not cooling, when I touch the compressor there is no vibra
... Read more
tion,so all i did is removed the compressor relay, and I found out that the wire is burned and melted the connector, i order the relay from parts select and install it.1.remove the capacitor and install it to the new relay. 2.put a new connecrtor from the wire.3. install the compressor relay.easy as 1,2,3.
Read less
The evaporator is always located on the inside of the refrigerator, usually inside the freezer compartment. It also resembles a radiator.
The evaporator is always located on the inside of the refrigerator, usually inside the freezer compartment. It also resembles a radiator.
This heat exchanger, also known as a suction or capillary tube, is an essential component of your refrigerator or freezer’s sealed system. It transfers heat from inside the appliance to the outside environment, helping maintain a consistent temperature for optimal food preservation. By carrying refrigerant between the condenser and evaporator, it ensures efficient cooling performance. A properly functioning heat exchanger improves energy efficiency and supports a longer appliance lifespan.
This heat exchanger, also known as a suction or capillary tube, is an essential component of your refrigerator or freezer’s sealed system. It transfers heat from inside the appliance to the outside environment, helping maintain a consistent temperature for optimal food preservation. By carrying refrigerant between the condenser and evaporator, it ensures efficient cooling performance. A properly functioning heat exchanger improves energy efficiency and supports a longer appliance lifespan.
Installation Instructions
Mike from Jacksonville, FL
Copper lines leaking freon
Removed the inside evaporator coil to do inside solder job, use torch to heat solder joints on the outside drier in order to remove it and install new drier. Soldered Heat exchanger line to drier and 1/4” copper line to compressor. Wrapped with new insulation wrap. Pulled a vacuum on system and then charged with 4.4 ounces of 134a freon.
... Read more
Works like a champ again!
Read less
The compressor start relay attaches to the compressor in your refrigerator. If your refrigerator will not start, one of the most common parts to fail is the compressor start relay. Sometimes called the controller, this device is used to boost the compressor until the unit is running. Other common symptoms connected to start relays include: refrigerator will not start, will not cool, is making a clicking, humming or buzzing sound, or the compressor itself is warm to the touch. You may also smell a burnt plastic odor if the relay has failed. Shake the relay and listen for any rattling, as this is a sign that it is faulty.
The compressor start relay attaches to the compressor in your refrigerator. If your refrigerator will not start, one of the most common parts to fail is the compressor start relay. Sometimes called the controller, this device is used to boost the compressor until the unit is running. Other common symptoms connected to start relays include: refrigerator will not start, will not cool, is making a clicking, humming or buzzing sound, or the compressor itself is warm to the touch. You may also smell a burnt plastic odor if the relay has failed. Shake the relay and listen for any rattling, as this is a sign that it is faulty.
Installation Instructions
Linda from Gurnee, IL
The compressor would not run.
I removed the cover, used a multimeter to test the compressor circuit, and found the compressor start relay to be defective.
Ordered a new one and installed it when it arrived.
Ordered a new one and installed it when it arrived.
$109.93
In Stock
Compressor start relay kit is an original equipment manufacturer (OEM) part that fits some Kenmore, Frigidaire, Electrolux, Crosley, Gibson and White-Westinghouse refrigerators. It also fits some Kenmore, Frigidaire and Gibson upright freezers.
Compressor start relay kit includes the compressor start relay, run capacitor, wire harness adapter, 2 wire terminals, 2 wire connectors, 2 pieces of wire connection shrink tubing, the wire retaining clip and kit instructions sheet.
Clarification of instructions: Kit 5304491941 now uses a wire harness with white wires; attach the red compressor power wire to the wire harness adapter's white wire that plugs into the start device terminal at the outside edge of the start device.
Replaces original refrigerator and freezer compressor start relay part numbers 216649316, 218721119, 241524601, 241524605 and 5304468029.
Fits some refrigerators in the following series: Kenmore and Kenmore Elite 253; Frigidaire FRS, FRT, FRX, FSC, GLH, GLR, GS2, NGS, PHS, PLH and PLRS; Electrolux E23; Crosley CRSE; Gibson GRS and GRT; and White-Westinghouse WRS and WRT. Also fits some upright freezers in these series: Kenmore 253; Frigidaire FFU; and Gibson GFU.
Compressor start relay kit is an original equipment manufacturer (OEM) part that fits some Kenmore, Frigidaire, Electrolux, Crosley, Gibson and White-Westinghouse refrigerators. It also fits some Kenmore, Frigidaire and Gibson upright freezers.
Compressor start relay kit includes the compressor start relay, run capacitor, wire harness adapter, 2 wire terminals, 2 wire connectors, 2 pieces of wire connection shrink tubing, the wire retaining clip and kit instructions sheet.
Clarification of instructions: Kit 5304491941 now uses a wire harness with white wires; attach the red compressor power wire to the wire harness adapter's white wire that plugs into the start device terminal at the outside edge of the start device.
Replaces original refrigerator and freezer compressor start relay part numbers 216649316, 218721119, 241524601, 241524605 and 5304468029.
Fits some refrigerators in the following series: Kenmore and Kenmore Elite 253; Frigidaire FRS, FRT, FRX, FSC, GLH, GLR, GS2, NGS, PHS, PLH and PLRS; Electrolux E23; Crosley CRSE; Gibson GRS and GRT; and White-Westinghouse WRS and WRT. Also fits some upright freezers in these series: Kenmore 253; Frigidaire FFU; and Gibson GFU.
What this part fixes:
- Freezer section too warm
- Fridge and Freezer are too warm
- Fridge too warm
Installation Instructions
MARK from LIBERTY LAKE, WA
Rear of upper shelf would freeze, while the rest of the freezer was dripping wet
We opened our freezer last week only to find the bottom 2/3 was barely cold, while only the rear of the upper shelf was cold. In fact, it was covered in frost, despite being a frost-free model. Our frozen veggies were slushy, not rock hard, and our frozen juices were all liquid. We defrosted the freezer, plugged it back in, but immediat
... Read more
ely noticed that we didn't hear the 'whhoooooosh' that you typically hear when you close the freezer door. After 30 minutes, the rear upper shelf was frosty again, but the rest was still at room temp. We figured the freezer was a goner, so we started looking at new freezers. I headed online to see if I could fix it, and I eventually found this site. I had learned online that these symptoms can be caused by either a bad capacitor, or a bad controller (which the capacitor plugs in to). I guess you can't necessarily tell which of the two parts is defective, so I chose to order/replace both of them. I ordered the correct parts from partselect.com, and they alerted me that Frigidaire has a new replacement part for the capacitor. When the parts arrived (quickly, ftw!), I unplugged the freezer and snipped the two wires leading to the controller. Next I unplugged the controller from the compressor housing. I spliced the replacement controller's wires into the freezer's wires (using my own wire nuts...as none were included with my order :( ). I snapped the new controller onto the compressor mounting, and then plugged the capacitor in. I plugged the freezer back in, and it was time for the moment of truth. The interior light of the freezer came on, and I could hear the compressor 'humming'. I could hear it humming before the repair, so the big test was to see if it got cold. I was nervous because the freezer DIDN'T make the 'whoooshing' noise right away, but after just an hour, the 'test' mug of water was already turning into ice. It was fixed!!!! If you have these symptoms, you CAN do this!!! Unplug the freezer. Cut two wires. Unplug the controller. Splice two wires. Plug in the new controller. Snap in the new capacitor. DONE!!!
Read less
MAKE THIS REPAIR A GUARANTEED WIN
OVER 2 MILLION PARTS TO ENSURE VICTORY
This compressor start relay is a replacement electrical component that helps start and protect the compressor during operation. It is commonly replaced when cooling systems fail to start, click repeatedly, or shut down shortly after startup. Proper fitment should be verified prior to installation.
This compressor start relay is a replacement electrical component that helps start and protect the compressor during operation. It is commonly replaced when cooling systems fail to start, click repeatedly, or shut down shortly after startup. Proper fitment should be verified prior to installation.
This overload protector helps safeguard the appliance by interrupting power when excessive current or overheating is detected. It plays a critical safety role and is typically replaced when the appliance fails to start or repeatedly trips during operation.
This overload protector helps safeguard the appliance by interrupting power when excessive current or overheating is detected. It plays a critical safety role and is typically replaced when the appliance fails to start or repeatedly trips during operation.
This refrigerator compressor is a key component in the cooling system, responsible for compressing and circulating refrigerant gas throughout the appliance. It increases the pressure and temperature of the gas before sending it through the condenser coils, where heat is released and the gas condenses into a liquid. The refrigerant then travels to the evaporator, where it expands and evaporates, creating a cooling effect that is distributed throughout the refrigerator. A malfunctioning compressor can lead to poor cooling performance or complete system failure. Proper lubrication and cooling are essential for maintaining its efficiency and extending the life of your appliance.
This refrigerator compressor is a key component in the cooling system, responsible for compressing and circulating refrigerant gas throughout the appliance. It increases the pressure and temperature of the gas before sending it through the condenser coils, where heat is released and the gas condenses into a liquid. The refrigerant then travels to the evaporator, where it expands and evaporates, creating a cooling effect that is distributed throughout the refrigerator. A malfunctioning compressor can lead to poor cooling performance or complete system failure. Proper lubrication and cooling are essential for maintaining its efficiency and extending the life of your appliance.
