My Orders
Snapper Pressure Washer Parts
GET YOUR OFFICIAL Snapper PARTS TO ENSURE VICTORY
Shop By Appliance
View MorePopular Snapper Pressure Washer Parts
Made of durable rubber and plastic components, this Fuel Valve and Bushing are designed for use in over 150 models of generators and pressure washers. This item is sold as a kit, including the valve and the rubber cap. Its primary purpose is to deliver fuel from the tank to the carburetor.
This part is found on the underside of the fuel tank and should be replaced when it is worn or damaged. When malfunctioning, it may cause your engine to be starved of fuel and run rough or not at all. You will need a screwdriver and pliers to complete this repair.
Customers rate this repair as Easy.
Made of durable rubber and plastic components, this Fuel Valve and Bushing are designed for use in over 150 models of generators and pressure washers. This item is sold as a kit, including the valve and the rubber cap. Its primary purpose is to deliver fuel from the tank to the carburetor.
This part is found on the underside of the fuel tank and should be replaced when it is worn or damaged. When malfunctioning, it may cause your engine to be starved of fuel and run rough or not at all. You will need a screwdriver and pliers to complete this repair.
Customers rate this repair as Easy.
Installation Instructions
James from PICAYUNE, MS
Dry rotted rubber
Put some dish soap on the rubber, push into the tank hole, slip 1x2 into the handle of the tank and over the new part and pry down pushing it into the hole. Took about 2 minutes.
Used to connect the hose that supplies the chemical cleaning solution (soap), this OEM replacement Chemical Injection Kit consists of the brass fittings, a metal ball, a spring, and a rubber seal, and is an exact replacement for various pressure washers.
If the cleaning solution will not dispense, it is possible that you need a new Chemical Injection Kit. Inspect it for signs of wear or damage and replace it if needed. This part is known to wear over time. You will need a wrench set to complete this repair.
Customers rate this repair as Easy.
Used to connect the hose that supplies the chemical cleaning solution (soap), this OEM replacement Chemical Injection Kit consists of the brass fittings, a metal ball, a spring, and a rubber seal, and is an exact replacement for various pressure washers.
If the cleaning solution will not dispense, it is possible that you need a new Chemical Injection Kit. Inspect it for signs of wear or damage and replace it if needed. This part is known to wear over time. You will need a wrench set to complete this repair.
Customers rate this repair as Easy.
Installation Instructions
Carl from ARCADIA, FL
The copper fitting on the chemical injection broke.
I order the part from this site and received it within a week. the only problem was that spring was missing out of the sealed bag. NO PROBLEM!!! I cut a ball point pen spring to fit and everything works just fine. You just have to remember to put the spring in first, then the ball bearing and then the rubber o-ring.If you put them in back
... Read more
wards you pressure will fed directly into your chemical container!!
Read less
This is a genuine OEM sourced component which is specially designed for Craftsman pressure washers. It is an identical replacement for a missing or damaged outlet that was originally installed on a new unit, please make sure to check the appropriate diagrams of your model for the correct location and application of this item. Keep in mind this high-quality part is made of durable metal and is sold individually.
This is a genuine OEM sourced component which is specially designed for Craftsman pressure washers. It is an identical replacement for a missing or damaged outlet that was originally installed on a new unit, please make sure to check the appropriate diagrams of your model for the correct location and application of this item. Keep in mind this high-quality part is made of durable metal and is sold individually.
This is an authentic replacement part manufactured for use with pressure washers. The nozzle is used to provide an even spray when using soap or a chemical cleaner. This black soap nozzle is available as an individual replacement part, please see model diagram for nozzle kits for a specific model pressure washers.
This is an authentic replacement part manufactured for use with pressure washers. The nozzle is used to provide an even spray when using soap or a chemical cleaner. This black soap nozzle is available as an individual replacement part, please see model diagram for nozzle kits for a specific model pressure washers.
MAKE THIS REPAIR A GUARANTEED WIN
OVER 2 MILLION PARTS TO ENSURE VICTORY
This filter, also known as a water inlet screen, is designed for use with pressure washers and has a 1-inch diameter (including the surrounding rubber housing). The filter itself is made of mesh and is sold as an individual part that filters dirt and debris from entering your pressure washer. It is recommended that this part is routinely inspected to keep your equipment running smoothly and to prevent a damaged filter from allowing dirt into your equipment. This part sits in-between the hose from your home and the pressure washer itself and is a genuine OEM part that requires no tools to replace or install.
This filter, also known as a water inlet screen, is designed for use with pressure washers and has a 1-inch diameter (including the surrounding rubber housing). The filter itself is made of mesh and is sold as an individual part that filters dirt and debris from entering your pressure washer. It is recommended that this part is routinely inspected to keep your equipment running smoothly and to prevent a damaged filter from allowing dirt into your equipment. This part sits in-between the hose from your home and the pressure washer itself and is a genuine OEM part that requires no tools to replace or install.
This item is an authentic OEM sourced O-ring kit that replaces worn or damaged O-rings for the gun, hose and wand.Unfortunately, over time o-rings will wear out and they may begin to crack eventually requiring replacements. Refer to the appropriate diagrams for your model to ensure the correct replacement procedure. A screwdriver and a wrench set might be needed to take apart and reassemble the equipment. Note, this kit is sold as an individual item.
This item is an authentic OEM sourced O-ring kit that replaces worn or damaged O-rings for the gun, hose and wand.Unfortunately, over time o-rings will wear out and they may begin to crack eventually requiring replacements. Refer to the appropriate diagrams for your model to ensure the correct replacement procedure. A screwdriver and a wrench set might be needed to take apart and reassemble the equipment. Note, this kit is sold as an individual item.
This is an original part from Briggs and Stratton, Troy-Bilt, and Snapper for use with Pressure Washers. The outlet tube kit includes the O-ring. The pressure hose connects to the outlet tube, which threads onto the pump. The tool that you will need to replace the outlet tube kit is a Wrench Set.
This is an original part from Briggs and Stratton, Troy-Bilt, and Snapper for use with Pressure Washers. The outlet tube kit includes the O-ring. The pressure hose connects to the outlet tube, which threads onto the pump. The tool that you will need to replace the outlet tube kit is a Wrench Set.
This handle fastening kit includes two plastic thread wingnuts and two carriage bolts, which are essential for securely attaching the handle assembly to your pressure washer. The handle assembly is typically located where the handle connects to the main body of your machine. When these parts are broken, the handle will feel wobbly or loose, and there may be visible damage to the mechanism. It is crucial to fix the assembly promptly, as a loose handle can pose safety risks and make it difficult to operate the pressure washer effectively. Please note that this genuine OEM kit is sold individually, and the handle itself is not included.
This handle fastening kit includes two plastic thread wingnuts and two carriage bolts, which are essential for securely attaching the handle assembly to your pressure washer. The handle assembly is typically located where the handle connects to the main body of your machine. When these parts are broken, the handle will feel wobbly or loose, and there may be visible damage to the mechanism. It is crucial to fix the assembly promptly, as a loose handle can pose safety risks and make it difficult to operate the pressure washer effectively. Please note that this genuine OEM kit is sold individually, and the handle itself is not included.
This bottle of oil can be used in over 150 different types of machinery. It is most commonly used for pressure washers and generators from manufacturers such as Briggs and Stratton and Troy-Bilt. This detergent oil is warranty approved and specially compounded for warm weather use. Please note: it is important to avoid over filling your engine with oil.
This bottle of oil can be used in over 150 different types of machinery. It is most commonly used for pressure washers and generators from manufacturers such as Briggs and Stratton and Troy-Bilt. This detergent oil is warranty approved and specially compounded for warm weather use. Please note: it is important to avoid over filling your engine with oil.