Range Legs and Feet
Find your partEnter your model number or a part number and click "Search"
Take a photo of your product’s model number plate and upload it to find parts fast!
Here is an example model number plate:
Popular Range Legs and Feet
PartSelect Number PS2353327
Manufacturer Part Number WB02T10461The Grate Foot is a black rubber part which attaches underneath the grate in order to protect your stovetop from being scratched, which it does by cushioning the grate on your gas range. If this part appears visibly broken or no longer holds in place, which can happen to these feet over time, then it should be replaced. Check your model number and user manual to see if this part is right for you. Because this part is sold individually, make sure to order the quantity that you require. We generally recommend checking all of the grate feet on your appliance and replacing them at the same time, since it is an inexpensive part and they tend to wear out at around the same rate. Spares are good to have in the event of future failures. Before beginning this repair, ensure that the surface is cool to the touch. Simply pull the worn or cracked foot out and install the new grate foot. This process should not require any tools or accessories.
Fixes these symptoms
- Touchpad does not respond
- See more...
FRANK from MEMPHIS, TN
The cooktop had a shorted out burner control.Unpllug the cooktop and turn off the gas supply. Remove the grates and burners.(they just lift out). Using a torx screwdriver, remove all the torx screws below where the burners sit. There are three screws per burner, except the power burner which has only two screws. Genly lift the stainless steel cooktop, separating it from the rest of the enclosure. Hold the electrodes with one hand, while gently twisting and pulling the wire connector off. Now, remove the aluminum covered foam piece. You will now have acess to the wiring harness assembly. Disconnect the quick connectors and replace with the new assembly. Re-assemble in the reverse order and you're done. About 1.5 to 2 hours. Good Luck Read more...
PartSelect Number PS11744009
Manufacturer Part Number WP74002557This is a leveling leg for your oven, range, or stove. The leveling legs on your oven allow your appliance to sit perfectly flat. The new one may be longer in length than your original, but will work the same. Install the new leveling leg, and test if you have it adjusted properly by putting the appliance on four legs. Adjust in or out as required if your oven is rocking. It is recommended to check the other three leveling legs on your appliance in case they are also damaged or worn. The leveling leg measures 1.859", is all black in color, and is made entirely out of plastic.
Eric from Goldens Bridge, NY
cracked glass top and broke leveling leg in moving the stoveDirected my wife because I have shoulder injury. She did all the work. Read more...
Grate Foot Kit
PartSelect Number PS2373826
Manufacturer Part Number 5304475129This kit includes 8 rubber feet and adhesive. This surface burner grate pad set is for ranges. Surface burner grate pad set contains the four pads that attach to the bottom of the burner grate to prevent the cooktop from being scratched.
Burner Grate Pads - Kit of 5
PartSelect Number PS389174
Manufacturer Part Number 814323These pads go on the bottom of your gas cooktop grates to prevent them from moving and scratching the top of your appliance.
Sabrina from Mooresville, NC
several grate pads fell out/lost /broke during cleaningThe only real issue was locating the proper adhesive to ensure that the new pads would not fall out. The small insert paper slip in the package noted that a RTV adhesive should be used. After much searching at the home improvement super store, I learned it would be found at an auto supply store. It is black, and is for high temp use. It is available in a small tube for around $2.00. The RTV is usually used to make gaskets for heat/oil exposure in auto repair. I did have trouble removing a broken stub from a pad that had broken off in the hole. I used an awl to get what I could and push the rest into the hole deeper, then insert a new pad with along with the adhesive. Read more...
Grate Pads - Set of 4
PartSelect Number PS988447
Manufacturer Part Number 8186321Also known as grate feet.
PartSelect Number PS2339673
Manufacturer Part Number WB02K10182
Bumper Pad Set of 4
PartSelect Number PS389208
Manufacturer Part Number 814383***NOTE: This part has been substituted by the manufacturer and may not appear the same as the original but should function the same. These pads go on the bottom of your gas cooktop grates to prevent them from moving and scratching the top of your appliance.
Eric from Durango, CO
Too much heat caused the turntable to shatter and the table support ring to melt.Washed the turntable and placed it in the microwave. Read more...
Grate Feet - Kit of 4
PartSelect Number PS2330208
Manufacturer Part Number W10185266This kit contains 4 grate feet for a range. These are the feet to fit your burner grates so the burner will not scratch your cooktop. The are black in color and made of rubber. These feet are fitted with a specific fire-resistant adhesive. If necessary, be sure to order adhesive separately. Be sure your burners are off and have cooled down to the touch before replacing these parts.
RICHARD from BROKEN ARROW, OK
replace pads or feet on steel grate of gas stovepull old ones out of legs. need to glue new ones in, they fit too loose. Some kits contain glue. get some high temp head gasket cement. a drop on each one is plenty. I used some old porcelain glue and hope it will hold. the pads are 2 bucks each plus shipping so don't let them get away!!! Read more...
PartSelect Number PS977569
Manufacturer Part Number 316272900This part is sold individually. The leveling leg is black in color and measures approximately 2 inches in length. It is made of plastic. The leveling leg is found underneath your range and may crack or wear down over time. This will need to be replaced if it has broken or gone missing. If you notice your oven is wobbling or uneven it may be due to the leveling leg needing to be replaced. This part can be adjusted to accommodate different heights due to uneven flooring. This is a genuine OEM part sourced directly from the manufacturer.