Range Fans and Blowers

Shop By Brand

Popular Range Fans and Blowers

Your Price
$116.81
  In Stock
Range Cooling Fan
★★★★★
★★★★★
4 Reviews
PartSelect Number PS12347171
Manufacturer Part Number W11107275
Whirlpool Genuine OEM W11107275 Range Cooling Fan Motor. Possible Repair Solution For: Will not start, takes too long to cool Please Note: This is intended as a guideline only, as other items can cause the same symptoms. This part works with the following brands: Whirlpool, Roper, Admiral, Maytag, Hardwick, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Amana, Kenmore, KitchenAid, Caloric
Fixes these symptoms
Your Price
$58.28
  In Stock
Blower Wheel
★★★★★
★★★★★
8 Reviews
PartSelect Number PS2052494
Manufacturer Part Number 56000
If your dryer is noisy, will not tumble, or is not producing enough heat, you may need to replace the blower wheel. This part is white in color, and is made of plastic. This part is approximately 8 inches in diameter. The blower wheel is located near the bottom of your dryer cabinet. To access it for this repair, you will need to remove both the front panel and the front bulkhead assembly. Before you begin this repair, be sure to disconnect the power source to the dryer. To complete this repair, you will need a 5/16 inch nut driver, a 1/4 inch nut driver, a pair of locking pliers and a 7/8 socket with a short extension and a ratchet.
Fixes these symptoms
  • No heat or not enough heat
  • Noisy
  • Takes too long to dry
  • See more...
Installation Instructions
Rick from Birch Run, MI
Blower fan cracked
Unplug the power cord from the unit. Remove the lower front panel; then the upper front panel including the door (unplug wire to door switch). Then remove the cover on the fan housing. Need to block the motor from turning; I used a stick to jamb the front of the motor; then unscrew the old blower fan and screw on the new one. Then replace the cover and put front panels back on. Read more...
Your Price
$25.45
  In Stock
Evaporator Fan Blade Kit
★★★★★
★★★★★
5 Reviews
PartSelect Number PS304684
Manufacturer Part Number WR60X114
Fixes these symptoms
Installation Instructions
Keith from Fort Worth, TX
Noisey fan/motor (bad motor bearing ?)
Removed 2 phillips head screws to remove ice maker (could have just loosened them)
Pulled fan off of shaft
Removed 2 phillips head screws on motor bracket , disconnected three motor wires & removed motor.
reversed process to install new motor & fan blade.
Space was a little tight for two hand and arms, but do-able.
Read more...
Your Price
$28.75
  In Stock
Convection Fan Blade
PartSelect Number PS3409337
Manufacturer Part Number 318398302
Installation Instructions
John from Stevensville, MD
replacing the fan on a convection oven (fan was making a vibration noise)
This was the first time replacing the fan. It is a lot easier to work in the oven compartment with the oven door removed, only two screws on the door and the hinges were released. I found that a couple of the screws were either rusted or stripped so I used a pair of pliers to remove the screws that were holding the diffuser in place. Once there was access to the fan I found that the fan was warped and that the blades were scraping against the back wall of the oven. The next challenge was to remove the retaining nut. I used a sheet metal screw to secure the warped fan to keep it from spinning. once I figured out that you have to turn the retaining nut to the right to loosen, it came off easily. 1/2" socket with extension. When I replace the fan I used two washers for spacers to make sure that the fan would not scrape the wall of the oven. Its been tested many times and the oven does not make that horrible sound anymore. Read more...
Your Price
$20.10
  In Stock
Fan Blade
PartSelect Number PS1480806
Manufacturer Part Number WB06X10706
This fan blade, also known as a stirrer blade, is a genuine OEM replacement part for your microwave. This is a fairly easy repair. To complete it, you will need a screwdriver to disassemble the fan assembly. Unplug the microwave before you begin this repair. Remove the fan cover and existing fan blade, and screw the new one in place. Reassemble all parts.
Your Price
$16.17
  In Stock
HUB BLADE Assembly
PartSelect Number PS1020933
Manufacturer Part Number WB02T10289
Installation Instructions
Calvin from Merced, CA
Replaced the inside frame
I had to take the intire oven apart, back included. Read more...
Your Price
$12.08
  In Stock
FAN-CONVCT
PartSelect Number PS10066087
Manufacturer Part Number W10758272
Your Price
$84.08
  In Stock
Exhaust Vent Blower Wheel
★★★★★
★★★★★
2 Reviews
PartSelect Number PS11757592
Manufacturer Part Number WPY707985
This exhaust vent blower wheel is almost seven inches in diameter, and just under four inches deep. It is made entirely of metal and is used with a range's venting system.
Installation Instructions
Janellen from Aiken, SC
blower motor died
Pulled the motor and blower wheel from below. Replaced both. I think it was easier to replace the two together than just the motor.I also had old light indicators so we replaced them since the stove was sort of apart. The repair was not difficult at all, and my 30+ stove top looks and runs great! Read more...
Your Price
$16.86
  In Stock
BLADE FAN
★★★★★
★★★★★
1 Review
PartSelect Number PS243069
Manufacturer Part Number WB2X8351
Your Price
$6.17
  In Stock
Fan
PartSelect Number PS3522731
Manufacturer Part Number 3B72559A

Brands