Porter Cable Compressor Seals and Gaskets

It is a genuine manufacturer sourced replacement part that is specially designed for Craftsman air compressors. This gasket provides an air-tight seal for the cylinder head assembly. Over time gaskets tend to get compressed, become brittle and crack eventually requiring replacement to maintain peak performance. It is made from durable, high quality composite material and it is sold individually.

This O-ring tube seal helps create an airtight connection where the tube enters the compressor head, supporting proper pressure and efficient operation. Made from durable rubber, it is designed to withstand heat and wear during regular use. Replacing a worn or damaged seal can help prevent air leaks and restore consistent compressor performance.Provide your feedback on BizChat

Genuine Porter Cable replacement part, this item is sold individually. Head Gasket Sold Separately. This part is used in the all of the compressors models listed below. When air is pumped by the piston it passes through the Valve Plate into the compressor tank. There are reeds on the valve plate that will eventually wear out, and the Valve plate will need to be replace. It is advisable at this time to replace the Graphite Gasket Kit, part number D30139.

This replacement tube seal is a high quality item that is supplied by original equipment manufacturer for use with Craftsman air compressors. It is placed on the outlet tube coming from the head of the compressor. Please note this durable rubber tube seal is sold individually.

O-rings are made to contain thousands of PSI pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. rnrnThere are many causes for O-Ring failure. The most common among power tools are: • <u>Extrusion and Nibbling</u> - The O-ring has ragged, tattered edges. These are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • <u>Abrasion</u> - One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that it too rough, contains grit or is too smooth to allow lubrication. • <u>Over Compression </u> - The O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • <u>Heat Hardening</u> - The O-ring has a pitted or cracked surface, and is often flattened on both sides. Caused by temperature exceeding o-ring capacity. • <u>Weather/Ozone Cracking</u> - The O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching (greater that 5%) causes similar cracking.

This is a genuine manufacturer-sourced replacement gasket, it is specially designed for use with Craftsman air compressors. It is utilized to provide an air-tight seal for the cylinder head, over time it may begin to wear out and crack eventually requiring a replacement to maintain peak performance. Please refer to the appropriate diagrams of your model for the correct location and use of this hardware. This high-quality component is made of durable composite material and it is sold individually.

O-rings are made to contain thousands of PSI pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. There are many causes for O-Ring failure. The most common among power tools are: • <u>Extrusion and Nibbling</u> • The O-ring has ragged, tattered edges. These are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • <u>Abrasion</u> • One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that it too rough, contains grit or is too smooth to allow lubrication. • <u>Over Compression </u> • The O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • <u>Heat Hardening</u> • The O-ring has a pitted or cracked surface, and is often flattened on both sides. Caused by temperature exceeding o-ring capacity. • <u>Weather/Ozone Cracking</u> • The O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching (greater that 5%) causes similar cracking.

The gasket is sourced from the original manufacturer to ensure quality. This item is intended to be used with air compressors from Porter Cable, Black and Decker, and DeWalt. The gasket is used to seal the connection between the cylinder head and the body of the cylinder. This item is available as an individual replacement part.

Genuine OEM replacement parts kit. This Gasket Kit is used to prevent air leaks in the compressors listed below. Over time the gaskets will become compressed or cracked and you will hear an air leak coming from the compressor. They will need to be replaced. This would be a good time to inspect all the other wear parts of the compressor.

This is a genuine Craftsman replacement gasket, it is supplied directly from the original equipment manufacturer for use with air compressors. It is the special component which helps to provide an air-tight seal for the cylinder head assembly, over time the gasket may wear out and crack eventually requiring a replacement to maintain peak performance. This high-quality part is made of durable composite material and it is sold individually.