My Orders
- Home
- ZSC2201NSS01
- Instructions
ZSC2201NSS01 General Electric Microwave - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven shut down when TCO (thermostat) detected overheat. Once cutoff, it has to be replaced not reset.
11 of 14 people
found this instruction helpful.
-
R C from Eglin Air Force Base, FL
- A Bit Difficult
- 1- 2 hours
-
Pliers, Screw drivers, Wrench (Adjustable)
The spacesaver is mounted over the stovetop. I removed the oven, then removed all the screws from the cover. Removed the cover and located the TCO and removed the wiring and the TCO. Ordered the part VIA internet and replaced it . It helps a little that I was Radar tec. and taught Electronics for 10 years and repaired lots of Microwaves
... Read more
. However anyone could do it just watch what you remove and replace in reverse order.
Read less
Was this helpful?
Thank you for voting!
Microwave does not have power at all, though outlet has power
10 of 11 people
found this instruction helpful.
-
Ronie from BRIARWOOD, NY
- Really Easy
- Less than 15 mins
-
Screw drivers
unplugged power cable / unhooked front vent / unscrew the monitor panel / slide up to dislodge / take the fuse out and put in the new one in / fuse is located right in front of monitor panel once its open might be covered by wirings / you can unpin the cables from the panel to make it easier for you just make sure to put it back properly
... Read more
or you can have somebody hold the panel for you. Installing the fuse is easy waiting for the parts is crazy......
Read less
Was this helpful?
Thank you for voting!
Lack of power to unit
11 of 16 people
found this instruction helpful.
-
Neil from Williston, VT
- Easy
- 15 - 30 mins
-
Screw drivers
This is the second time replacing this fuse, last time was exactly one year ago. The first time I replaced it, I removed the oven from the wall & disassembled a number of things to reach the culprit. This time I left the oven mounted & was able to access the 2 grille mounting screws on the top of the grille & remove it. Next comes the bla
... Read more
ck plastic air deflector held by two screws & is mounted in front & on the right, it is shown on the parts list just above part #1434. After removing it, remove the two silver cover screws in the front, this cover also doesn't have a part # but is shown to the right of part #1410. At this point you can lift this cover enough to access the fuse which is on the left & held in place by one tiny screw through the clamp at the top, (careful not to drop it when removing). PS: Don't forget to cut the power to the microwave before starting!
Read less
Was this helpful?
Thank you for voting!
No cooking Power
12 of 19 people
found this instruction helpful.
-
Norbert from Minnetonka, MN
- A Bit Difficult
- 15 - 30 mins
-
Pliers, Screw drivers
Had to remove outer cover (special screws involved). Found the correct part at PartSelect.Com and it arrived 3 days later as promissed.
This oven has diffcult electrical connections at switch to get disconnected. I found it easier with the sw loose and in hand so that the connectors can be released with a small screwdriver. ... Read more r />
One has to this in order to test the part wirh an ohm meter. I found the sw did not close but remained open and thus caused the oven not to function.
Removing interconnect switch is tricky but not difficult.
Outer cover replacement is not as easy as it should be, especially the sides.
All is well and working.
Microwaves are simple devices if you are know how to read and understand schemetic diagrams.
This oven has diffcult electrical connections at switch to get disconnected. I found it easier with the sw loose and in hand so that the connectors can be released with a small screwdriver. ... Read more r />
One has to this in order to test the part wirh an ohm meter. I found the sw did not close but remained open and thus caused the oven not to function.
Removing interconnect switch is tricky but not difficult.
Outer cover replacement is not as easy as it should be, especially the sides.
All is well and working.
Microwaves are simple devices if you are know how to read and understand schemetic diagrams.
Read less
Was this helpful?
Thank you for voting!
after 3-4 minutes microwave display would blink and unit would just cut out.
12 of 20 people
found this instruction helpful.
-
Larry from Brookfield, CT
- A Bit Difficult
- 30 - 60 mins
-
Wrench set
This was the second time I've had to open up the microwave. 1st time display would blank out but system would continue to operate. Found solder connections on board to LED display were defective. Resoldered and unit was fine. This time I found the connection to the oven cavity temp cut-off was bad, plastic connection cover melted. When
... Read more
unit operated bottom lead and wire would heat up. Couldn't measure a Discernable distance so either wire or connector connection surface was not sufficient to carry the current. 1st replaced sensor still wire heated up. Replaced connector and there was no sign how heat from resistances.
Read less
Was this helpful?
Thank you for voting!
Microwave function not working
8 of 9 people
found this instruction helpful.
-
Aaron from BLUE RIDGE, TX
- Easy
- 15 - 30 mins
-
Screw drivers
1) Removed 4 screws securing the microwave to the cabinet.2) Slid microwave out, unplugged and placed on a work surface that allowed lower trim to hang over. 3a) Removed two screws and removed the cover on top of the oven. 3b) Unplugged high voltage plug from Magnatron. 4) Removed wires from overtemp fuse mounted to Magnatron. 5) Removed
... Read more
the four screws securing the Magnatron to the oven. 6) Removed Manatron. It's a tight fit, but can be done without removing anything else. 7) Replaced Magnatron. This is where I needed the magnetic part retrieval tool. The nature of a Magnatron is the use of strong magnets surrounding the tube. Getting the four screws back into place wasn't possible with just a normal magnetic screwdriver tip. I used the retrieval tool to position the screws back in place. Be sure to not initially tighten any screw completely, until they can be evenly tightened. This ensures correct compression/seating of the shielding material near the neck of the tube. 8) Reverse removal steps. Plugged in and tested microwave function on a cup of tap water. 9) Reinstated in cabinet and got a big thank you kiss from the wife!
Read less
Was this helpful?
Thank you for voting!
Blown fuse in microwave
8 of 9 people
found this instruction helpful.
-
Frank from VIPER, KY
- Very Easy
- 15 - 30 mins
-
Screw drivers
One small Phillips screwdriver and one fuse puller (I used cord). Unplug unit. Remove the two screws on the vent face plate. Remove the one screw on the panel assembly. Gently let hang. Pull the fuse located on the upper left wall. Replace fuse. Reassemble.
Was this helpful?
Thank you for voting!
burned out light surface light bulb
10 of 16 people
found this instruction helpful.
-
Veronica from St Augustine, FL
- Easy
- Less than 15 mins
-
Screw drivers
the main issue I had is the appliance manual stating that the bulb should be "unscrewed". when I first read the manual, before I received the bulb on delivery, I tried "unscrewing" the bulb, which actually is a PLUG IN bulb. small wonder that it didn't come out! luckily I didn't break the connections off in the socket!
Was this helpful?
Thank you for voting!
Oven wouldn't sensor reheat & error code on display
8 of 11 people
found this instruction helpful.
-
Chris from Springfield, VA
- Easy
- 15 - 30 mins
-
Screw drivers
I looked at the exploded pic on your web site to find the location of the sensor. Next I removed the cover by unscrewing 15 screws then swaped the sensor and re assembled! Works great! Fixing it my self I saved at least 150$ and did not have to wait all day for a repair man who probaly would not have the part on the first visit.
Was this helpful?
Thank you for voting!
microwave would not heat
14 of 29 people
found this instruction helpful.
-
John from Erie, PA
- Easy
- 30 - 60 mins
-
Screw drivers
First remove all screws holding on outer metal casing of microwave. Next remove the back and bottom metal pieces. You will then be able to pull aside the outer casing so you can access the door switches. Check each switch with an ohm meter in both the open position and with the switch closed. If the ohm meter reads the same in both the
... Read more
open and closed position, the switch is bad. Check the top switch first. Replace switch and reassemble. Cheap fix for a costly microwave. Great customer service at Parts Select!
Read less
Was this helpful?
Thank you for voting!
burnt out bulb
13 of 27 people
found this instruction helpful.
-
Neal from Gardena, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
removed light cover and replaced defective bulb
Was this helpful?
Thank you for voting!
Sparking from the magnetron
5 of 5 people
found this instruction helpful.
-
Reid from LITTLETON, CO
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
Symptom: Terrible sparking coming from the right side of the microwave even with nothing in the microwave. The part that was behind the cover was the business end of what I learned was the magnetron,
Repair process: Without appliance repair experience I went onto Google and searched for parts for my model PEB1590DM2WW. I ... Read more was able to find a great parts schematic on partselect.com. At first I ordered a magnetron and while waiting for the parts to arrive I also learned that the capacitor can also fail easily as described in the other install feedback on the partsselect website. So I ordered a capacitor just in case. These convection microwaves are around $600 new so a $80 in parts is not out of line for 8 years of service.
I installed the magnetron first and turned it on. sparking immediately continued so I quickly shut the unit off. After replacing the capacitor and letting it charge for several minutes before trying to start the microwave cycle was the issue. I choose to leave the replaced magnetron as the original unit was discolored and felt the replacement was inexpensive insurance. I also learned that if the wave guide (which is a plastic/metallic composite material) that covers the opening to the magnetron is burnt or has metal melted to it as mine did it will act similar to the microwave having metal inside the enclosure and will continue to spark and basically melt the wave guide further. Replacing the wave guide was very easy as well.
I am very thankful for the knowledge base and support available from Partselect.com as they made this repair possible on my own. Thank you partselect.com
Repair process: Without appliance repair experience I went onto Google and searched for parts for my model PEB1590DM2WW. I ... Read more was able to find a great parts schematic on partselect.com. At first I ordered a magnetron and while waiting for the parts to arrive I also learned that the capacitor can also fail easily as described in the other install feedback on the partsselect website. So I ordered a capacitor just in case. These convection microwaves are around $600 new so a $80 in parts is not out of line for 8 years of service.
I installed the magnetron first and turned it on. sparking immediately continued so I quickly shut the unit off. After replacing the capacitor and letting it charge for several minutes before trying to start the microwave cycle was the issue. I choose to leave the replaced magnetron as the original unit was discolored and felt the replacement was inexpensive insurance. I also learned that if the wave guide (which is a plastic/metallic composite material) that covers the opening to the magnetron is burnt or has metal melted to it as mine did it will act similar to the microwave having metal inside the enclosure and will continue to spark and basically melt the wave guide further. Replacing the wave guide was very easy as well.
I am very thankful for the knowledge base and support available from Partselect.com as they made this repair possible on my own. Thank you partselect.com
Read less
Was this helpful?
Thank you for voting!
Opened door to get food put more food in closed door it wouldnt work
4 of 4 people
found this instruction helpful.
-
Henry Totten from GROVES, TX
- Really Easy
- 30 - 60 mins
-
Screw drivers
Everything worked on the display light inside worked but when you closed the door and set time it would start counting down but not heating nor would the turntable turn. Started reading troubleshooting chart and first thing I did was removed the cover and checked door switches and found primary door switch wasn't working so I ordered a ne
... Read more
w one installed it and it worked. Anyone doing this has to be very careful because of the stored energy in the capacitor is strong enough to kill.
My micro is only 2 years old so I was hoping it wasn't anything major.
My micro is only 2 years old so I was hoping it wasn't anything major.
Read less
Was this helpful?
Thank you for voting!
runs but does not heat
4 of 4 people
found this instruction helpful.
-
Scott from PIEDMONT, CA
- Easy
- 15 - 30 mins
-
Screw drivers
I removed the main cover ( torx security bit required) and tested the magnetron, capacitor, diode and door interlock switches according to instructions found on the internet. The capacitor and diode tested good but the magnetron looked burnt and corroded on the tip. The magnetron I received was an exact replacement for the original. It wa
... Read more
s easy to replace the magnetron which arrived in 2 days standard shipping. I also cleaned the fan while I had access to the inside area. Hoping to get another 18 years use from the microwave!
Read less
Was this helpful?
Thank you for voting!
mICROWAVE WOULD NOT HEAT
5 of 8 people
found this instruction helpful.
-
Peter from Bessemer, MI
- Really Easy
- 15 - 30 mins
-
Screw drivers
I REMOVED THE TOP PANEL OF THE MICR0WAVE AND THEN REMOVED ONE SCREW TO REMOVE THE CONTROL PANEL. rEMOVED OLD SWITCH. SNAPPED IN NEW SWITCH AND CONNECTED WIRE. REPLACED CONTROL PANEL AND UPPER PANEL.
Was this helpful?
Thank you for voting!