EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

ZSC2000FWW02 General Electric Microwave - Instructions

All Instructions for the ZSC2000FWW02
1 - 15 of 48

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Microwave would turn on and count down, but not heating and not rotate turntable. Pressing door up would occasionally start heat.
40 of 67 people found this instruction helpful.
  • Michael from Ridgefield, CT
  • Really Easy
  • Less than 15 mins
  • Screw drivers
First I disconnected the power and opened the door. Then I removed the top screws holding the top vent louvers, then removed the screw at the top of the touch pad. The touch pad removes by sliding up slightly then tilting top out. I unscrewed two screws holding the door latch assembly. Press the tab to remove and replace switch. Reco nnect wires, reseat latch mount by placing top bracket tab in place first, allign and secure with screws. Reseat touch pad by placing bottom tabs in first, tilt forward and press up to seat top tabs, secure with top screw. Secure vent louver screws, plug in and watch your microwave work again.
Was this helpful?
Thank you for voting!
Microwave runs with the door open
37 of 58 people found this instruction helpful.
  • Thomas from Andover, NJ
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Remove microwave outer cover. Turn on side & locate the upper & lower door switches. Better to replace in pairs even if one is ok. Remove the wire harness to each switch. Then replace switch and re connect the wire harness. Re attach outer cover
and test to see if that solved the problem. If so then well done!!
Was this helpful?
Thank you for voting!
Broken shaft -- turn table would not turn.
22 of 24 people found this instruction helpful.
  • James from OKLAHOMA CITY, OK
  • Really Easy
  • Less than 15 mins
Safety TORX driver removed screw. Ceramic cover removed with ease. Shaft pulled straight up and out. Broken piece not retreivable and left in base of oven. New shaft inserted over "D" stub. Ceramic cover replaced and screw tightened.

When the ceramic cover is removed, this allows the glass cover for the UV heating unit to be removed, cleaned, replaced. I recommend doing this.
Was this helpful?
Thank you for voting!
Everything seemed to work with the controls, but when you pressed start the light would come on and nothing else. The turntable and heating system would not function.
25 of 43 people found this instruction helpful.
  • Keith from Bowling Green, KY
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I unplugged it, removed the outer shell with torque bits and a screwdriver, drained the main capacitor, and began debugging the circuit with my fluke multimeter, found the bad primary interlock, googled the part number, ordered the part, received it in 2 days, replaced the interlock in about 2 minutes, and put the cover back on. Fixed. Saved me about $200 over buying a new unit and was grateful for partselect's great service.

-Keith Packard
Was this helpful?
Thank you for voting!
Microwave would not heat food
18 of 25 people found this instruction helpful.
  • Robert from Dayton, NV
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
First and most important - unplug AC power 24 hours before service.

I removed the vent cover above the main door, then I removed the screw which holds the control panel in place, unplugged the main connector on the control panel so I would have enough room to work, removed grounding screw from the DIODE ASSY, pulled connector o ff the CAPACITOR with pliers, installed new DIODE ASSY.

After installation of DIODE and the control Panel, I plugged in the AC power and allowed the CAPACITOR to charge - this takes about an hour or so, then test. Works perfect!
Was this helpful?
Thank you for voting!
Original part was fried
20 of 34 people found this instruction helpful.
  • michelle from virginia beach, VA
  • Difficult
  • 1- 2 hours
  • Screw drivers
Had to remove microwave from the wall. Then disassemble entire top assembly to get to the part. Easy enough to replace after that. Then just reassemble and reinstall. About 2hrs. total
Was this helpful?
Thank you for voting!
had to press door opener slightly to work
16 of 24 people found this instruction helpful.
  • Lawrence from East Patchogue, AL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Removed screws holding outer shell. Pushed in door handle to identify faulty switch. Ordered part. Pryed switch out with screw driver and unplugged. reinstalled new switch. Presto. BUT... I did NOT use both hands while working on the microwave. I did not release the energy from the capacitor or whatever holds the killer amperage ev en when unplugged. It would be advisable to do this first. I did not because it seemed complicated, so I was EXTREMELY CAREFUL about not touching anything else inside the unit. I used one hand only so if I did touch something I would not get juiced through the chest. It was a piece of cake repair, but I would not go deeper without doing the discharge routine.
Was this helpful?
Thank you for voting!
All power out. No display, not operational
15 of 22 people found this instruction helpful.
  • Steven from Gardiner, ME
  • A Bit Difficult
  • 1- 2 hours
  • Screw drivers
Remove microwave and set on flat surface. Remove all screws on top. Remove all screws around back edge holding top on. Finally remove the screws on botton holding top on and remove top. On left side on top, remove 6 screws holding black channel in place. Also remove 3 screws holding metal top in place. Now lift black channel up and u nplug 2 wires on cutout. Replace cutout and reinstall everything in reverse order. Worst part is taking microwave down and reinstalling.
Was this helpful?
Thank you for voting!
microwave turntable had a broken wheel
14 of 22 people found this instruction helpful.
  • Jane from Estero, FL
  • Really Easy
  • Less than 15 mins
Ordered a new part, installed it.
Was this helpful?
Thank you for voting!
I broke the ceramic tray on my Advantium Oven
11 of 14 people found this instruction helpful.
  • Mendi from Wentzville, MO
  • Really Easy
  • Less than 15 mins
The repair was simple -- I just placed the ceramic tray. It took longer to find the part! They had the best price, and my part came quickly!
Was this helpful?
Thank you for voting!
Oven shut down when TCO (thermostat) detected overheat. Once cutoff, it has to be replaced not reset.
11 of 14 people found this instruction helpful.
  • R C from Eglin Air Force Base, FL
  • A Bit Difficult
  • 1- 2 hours
  • Pliers, Screw drivers, Wrench (Adjustable)
The spacesaver is mounted over the stovetop. I removed the oven, then removed all the screws from the cover. Removed the cover and located the TCO and removed the wiring and the TCO. Ordered the part VIA internet and replaced it . It helps a little that I was Radar tec. and taught Electronics for 10 years and repaired lots of Microwaves . However anyone could do it just watch what you remove and replace in reverse order.
Was this helpful?
Thank you for voting!
No cooking Power
12 of 19 people found this instruction helpful.
  • Norbert from Minnetonka, MN
  • A Bit Difficult
  • 15 - 30 mins
  • Pliers, Screw drivers
Had to remove outer cover (special screws involved). Found the correct part at PartSelect.Com and it arrived 3 days later as promissed.

This oven has diffcult electrical connections at switch to get disconnected. I found it easier with the sw loose and in hand so that the connectors can be released with a small screwdriver.