ZISS480DXCSS General Electric Refrigerator - Instructions

had to remove ice maker and several panels to get to the fan. wires for fan encapsulated so had to cut old and new wires then solder them together while working inside the small freezer area. not too bad all in all took about an hour to get it done. no more wind thru the trees noise and is working fine

Unplugged the freezer. Then I gained access to the fan: remove the top freezer rack, remove the ice tray, remove the air flow manifold(needed to unscrew some screws), remove the manifold over the fan and cooling element. I unscrewed the fan mounting bracket. The fan motor's wires are plumbed through some plastic that i would have had t ... Read more o remove, so I decided instead to cut the wires and splice in the new fan motor. Then I put everything back together - the new motor works fine and doesn't make the whining noise.

We followed the instructions we found on this site.

First we unplugged the refrigerator.

Then we removed the control panel that has the ice type selection on it by releasing the three spring latches. These are accessible from the bottom of the panel looking up toward the ice dispenser. There are three holes. P ... Read more ress a narrow screwdriver or punch in each of these holes and then pull out the control panel. (Be careful not to disconnect the wires, but observe how the wires are routed.)

Then we removed the ice tube cover that covers the solenoid assembly. There were four screws. One was very rusty and it required some WD40 to loosen it. Once the cover was removed the solenoid was visible on the right. (It has a floating component that attaches to the "arm" of the flap. This is how the solenoid opens and closes the flap. The flap needs to close properly so ice does not build up in the door.)

There were three screws that had to be removed to get the solenoid out. (The top one you may just need to loosen once the bottom two are removed.) When the solenoid was removed we also removed the old floating component from the flap are and replace it with the new one. We slid this into the solenoid hole and then screw it in with the three screws.

Before we attached everything, we plugged in the refrigerator to test the solenoid. We dispensed some ice and waited to hear the flap close. (The flap close is slightly delayed so be patient.)

We attached the cover that was over the solenoid being careful to route the wires as they were when we started. We test the solenoid again. Then we snapped the control panel back into place and tested again.

We found that having the right size screwdriver made a difference especially dealing with rusty screws. It was also handy to have a good flashlight. Having extra hands was helpful to hold the control panel and cover while working on the solenoid and routing the wires.

First remove trim surrounding ice/water dispenser assembly. Use a flat spackle knife to obtain space between door and trim. Be careful not t scratch refrigerator door. Then pry trim off. This was the most difficult part of repair. The front plate of the dispenser is held to the back of the dispenser by two friction fastners and in the cas ... Read more e of my refrigerator a phillips screw (some don't have screw in middle). Use a small round tool like an allen wrench to push up on the 2 fastners to release them. Next push the front assembley aside and remove the 4 screws holding the back part of the dispenser. Push that assembly aside. Remove the defective solenoid assembly by removing the 3 mounting screws. The solenoid base can be worked out by slipping it out of the solenoid assembly plunger still attached to the dispenser door assembly. Next slide the plunger off of the dispenser door assembly. Install new solenoid assembly by reversing this procedure.
Hint - I found the ice door assembly (wr17x11653) also needed replacement and it is well worth the effort to replace both at the same time.

Removed access panel on freezer door, removed circuit board, removed and replaced solenoid, reinstalled previously removed parts

Pulled ice tub, removed auger rotation motor and solenoid housing, removed solenoid and replaced with new one and reinstalled. Checked solenoid was working by holding freezer door open and closing switch to door an activating ice switch-- solenoid picked up. Put ice tub with auger back into freezer.

no instructions came with the part so I wrote for help from your techs. They were able to tell me how to access the solenoid. From there I was able to figure the rest out. I had to remove the trim, electrical board, flap, springs and arm to reach the screws necessary to remove the solenoid. I removed some of the corrosion with a baking so ... Read more da paste so I could remove the screws. I carefully noted each step and position of the parts I removed and reversed the process to put things back after replacing the solenoid.

1) remove the ice bucket. 2) remove light cover and bulb. 3) remove back panel with 2 screws. 4) remove fan shield. 5) unlug 2 elec connections. 6) remove fan housing. 7) extract wiring grommet and use exacto knife to slice thru grommet along the length of it to release wires. don't cut light wires. 8) cut up old fan/light electrical plug ... Read more to free wire nubs for light. 9) install nubs in new fan plug. 10) remove old fan motor, pull blades. 11) install blades on new fan moter and install fan into housing. 11) reinstall

Determined that the little door that opens to allow full size cubes to fall was not opening. If you open freezer door, hold door switch in, select cubes and push in the lever that the glass pushes in you should hear the solenoid lift open which opens the little door. Mine was doing nothing. Removed ice bin and then removed icemaker motor ... Read more /solenoid section from back of freezer by disconnecting two wire harnesses and one screw. Found that solenoid smelled burnt and could see that inside of the solenoid was swollen out of round and burnt. Simple to replace.

Squeezed a flat blade screwdriver between the faceplate (buttons and lights) and the plastic part behind it and the front panel popped loose. I unscrewed the 4 cross-slotted screws on the panel behind the faceplate and could easily see the solenoid. I released the solenoid connector from the printed circuit board and removed its 3 screws. ... Read more It slides out. Replace with new part in reverse.

Just turn the cartilage out and put the new one. Very simple

it was easy. Open the fridge,untwist the old filter. Open the new filter, fill with tap water and twist in place. Run water through it for a few minutes to insure it is working and filters the water.

I watched the video, and noticed that they did not even turn off the water. The replacement took less than 30 seconds once the filter was filled with water.

I watched the video explaining how to do this and it was a snap. MY PROBLEM WAS COMPLETELY SOLVED. Partselect.com is a must for my household. I couldn't be happier!!!!!

with my hands