All Installation Instructions for General Electric Refrigerator ZISB360DNDII

bad tsting ice cubes/ water

it was easy. Open the fridge,untwist the old filter. Open the new filter, fill with tap water and twist in place. Run water through it for a few minutes to insure it is working and filters the water.

Parts Used:

Refrigerator Ice and Water Filter

Beverly from Jacksonville, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Needed new water and ice filter

simply read the instructions

Parts Used:

Refrigerator Ice and Water Filter

Marilyn from Green Valley, AZ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

no turn on

with my hands

Parts Used:

Refrigerator Ice and Water Filter

edward from orlando, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Ice and Water Filter needed replacement

I watched the video, and noticed that they did not even turn off the water. The replacement took less than 30 seconds once the filter was filled with water.

Parts Used:

Refrigerator Ice and Water Filter

Tim from Fort Worth, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Water Filter Red Light

Replaced Water Filter (twist off old filter; twist on new.)

Parts Used:

Refrigerator Ice and Water Filter

Charles from Foresthill, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

filter change

easy easy easy!!!!!

Parts Used:

Refrigerator Ice and Water Filter

Mary from Elk Grove, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Replace Dispencer blade

Removed the exterior 4 screws and 1 holding the metal rod underneath. Sepearated the plastic parts pulled out the dispensing mechanisim. Removed the lock washer, then removed the spacers and blades. Put the new blades in with the spacers and reversed the other steps and done.

Parts Used:

Refrigerator Ice and Water Filter

Rear Moving Dispenser Blade

Blade - Middle

Front Moving Dispenser Blade

Leonard from Hawthorne, CA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

0 of 2 people found this instruction helpful.

Was this instruction helpful to you?

water tasted funny

Simply twisted off the old water filter, unwrapped the new one and twisted it on.

Parts Used:

Refrigerator Ice and Water Filter

Charles from Enterprise, AL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 2 people found this instruction helpful.

Was this instruction helpful to you?

needed to replace the filter

replaced the filter with the new one i purchased

Parts Used:

Refrigerator Ice and Water Filter

richard from asheboro, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 3 people found this instruction helpful.

Was this instruction helpful to you?

water dispensed slow and filters too expensive and not very reliable

I just unscrewed filter and screwed in filter bypass

Parts Used:

Refrigerator Bypass

john from selbyville, DE
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

replaced filter

none required

Parts Used:

Refrigerator Ice and Water Filter

donnie from metairie, LA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Refrigerator freezing.

Temp. Sensor was under an egg shaped cover on the left side wall in the refrigerator. Remove the cover, cut the two wires to the old sensor and remove it. Connect the new sensor to the two wires using butt connectors. Replace cover and done.

Parts Used: