ZFSB23DNAKSS General Electric Refrigerator - Parts

This DC fan motor moves air across the condenser coils and compressor to help remove heat. A failed motor may cause poor cooling, a hot compressor, or humming and squealing sounds. Before replacing it, clean the coils and check the fan blade, wiring, and air path for dirt or damage. Confirm fit with the full appliance model, 4-pin plug, a...Read morend 11.3- to 12-volt rating. Unplug the refrigerator before removing the rear panel. Keep hands away from the blade, protect the cooling lines, and reinstall the panel before testing the unit.

This part regulates the humidity of your crisper bins. It does so by opening and closing vents on the bin. If your humidity control is broken or missing, you will need to replace it. This is a genuine OEM part from GE and is sourced directly from the manufacturer.

This is the replacement door stop, also known as a door stop bracket, for your refrigerator. It is made of black plastic, and is approximately 3 inches long and 1 inch wide. The door stop bracket stops the door from opening more than approximately 90 degrees. The stop can occasionally break, and this will allow the door to open more than ...Read more90 degrees. When this occurs, you will need to replace the door stop. This part is sold individually and is an OEM part.

This kit includes 1 cube solenoid, 1 armature, 2 tooth washers and 2 1/4 hex head screws.

10-16 pl pnp 5/8 szn - Sold individually.

This refrigerator or freezer drawer handle is a genuine replacement part designed to restore functionality and appearance to your appliance. Engineered for a secure fit, it provides a reliable grip for opening and closing the door or drawer with ease. Constructed from durable materials, this OEM component is built to withstand frequent da...Read moreily use. It is compatible with a range of models and replaces several older part numbers. Installation is typically quick and straightforward, often requiring only a few minutes and minimal tools. Before purchasing, confirm compatibility with your specific appliance model to ensure proper fit and performance.

This part is the replacement fresh food door gasket for your refrigerator. It is made of black rubber and is sold individually. The fresh food door gasket runs along the circumference of your refrigerator’s fresh food door and creates the seal that allows your refrigerator to regulate the temperature inside. If the gasket is worn, stretch...Read moreed, or damaged, your fridge may become too warm, and you may notice the door is sweating. The door also may not open or close properly because of a damaged gasket. To replace the gasket, carefully pull the old gasket out the grooves it fits in around the door. Press the new gasket into the same grooves snugly. This part is an OEM part from the manufacturer.

3 terminal.

This is the replacement drawer side rail for the left side of your refrigerator. It is made of white plastic and is approximately 12 inches long, and 2 inches wide. The slide rail supports the crisper drawer as it slides in and out. If the slide rail is broken, you may have difficulty sliding the drawer in and out. This rail is for the le...Read moreft side of the drawer, and the slide for the right side is sold separately. This part is sold individually and is and OEM part.

This ice bucket auger is a genuine OEM replacement part for your refrigerator freezer section. The auger rotates and separates the ice in the bucket. To replace it, start by pulling out the ice bucket assembly. Remove the cover, shield, and actuator arm bracket using a Phillips head screwdriver. Unhook the spring holding the arm in place ...Read moreto remove the arm. Use your screwdriver to pry off the e-clip and washer. Use a wrench to detach the auger from its housing. This part includes the auger only, not the assembly or housing.

Clips sold separately.

This part is the replacement torsion-fit spring for your refrigerator. It is made of metal and is sold individually. The torsion-fit spring provides tension to return the ice funnel back to its normal position after it dispenses ice. If your refrigerator is not dispensing ice or water properly, you may need to replace the torsion-fit spring. This is an OEM part sourced directly from the manufacturer.