ZFGP21HXCSS General Electric Refrigerator - Instructions

Just fallow video shows that it 123 !

This is a simple repair. You remove the two upper crisper drawers, remove the bottom slide draw that holds cheese, etc. Then lift up on the crisper pan cover and pull out. Note: the old crisper pan will have 2 rubber moldings you will need to move to the new one and there is a sponge molding that if you peel off very carefully you can pu ... Read more t on the new pan otherwise you will need to buy that. No one told me that and I wish they did... so that is why I am writing this.

follow the easy instructions replace 3 temperature sensors cut the wires and crimp them with new sensor and it works like new

I found instructions on the web about how to do this repair, so I ordered the part with confidence. But the instructions simply said "pull out the old switchlight". That was actually somewhat difficult as the clip on the side intended to hold the part in was stubborn. I eventually used a utility to slice off the clip. From that point, ... Read more it was just a matter of plugging in the new switchlight , which was very simple.

Reviwed an existing instruction ans was surprised at how easy it was to remove the existing gasket and replace it. No tools required at all.

Turns out it was only the frozen water that thawed when I unplugged the fridge for 24 hours.
New part returned, not used.
Service was excellent.

My GE SideBySide fridge stopped making ice. The green LED light on the icemaker was not blinking. The water dispenser worked fine. Fridge is only 5 years old. Freezer temp set at 7 degrees...fridge at 37 degrees. I have been using these temps since new. GE hotline suggested freezer temp should be at zero degrees. That did not work. Second ... Read more call suggested an airflow issue within the freezer...there should be 1 inch space between food and back wall. Still no ice. The water valve looks to be the issue. I ordered it and got it in 2 days. Valve is in the back bottom, refridgerator side. Push the white collars around the water hoses...Then pull the hoses out. An adjustable wrench removes the nut for the inlet hose. Disconnect 2 electrical plugs. Be sure to push the water hoses fully into the new valve. I pulled the white collars out a bit to insure a tight fit. I was surprised at how simple this was to install. As it turns out, I was still getting no ice. I ordered a new ice maker and now I'm getting ice. The icemaker was EVEN EASIER to install.

Remove glass, lift cover up in front, slide out, transfer parts seals and switch for crisper(one pivot screw. Remove rear seal by using finger nail to pull at gasket slowly pulling it back. Take your time. Reinstall cover and glass, snap pivoting cover back on.

removed the back cover, removed one srew that held the valve, disconnected water lines, and installed the new valve. Piece of cake!

My wife said we need to look for a new fridge because several plastic parts were broken. Instead, I looked on PartSelect and ordered replacement parts for the broken ones. In less than two hours with no tools required, The fridge looks much better on the inside. Lesson learned

I made my wife fix it.

Replaced evaporator fan motor, and this solved the whistling noise that had developed. Reviewed and followed the removal and installation instruction video as closely as possible. This was very helpful, with a few additions. For the model PS123NGPBBB GE refrigerator/freezer, there were a few differences from the video. There a was an addi ... Read more tional cover panel that was positioned vertically at the back of the freezer compartment below the auger motor assembly. It was necessary to remove this cover (4 screws) to gain access to the auger motor cover screws. The unit also has a different light configuration with 2 lights. I found it helpful to remove these light bulbs and the corresponding light fixtures in order to remove the evaporator motor assembly. As mentioned in the video, it was necessary to cut the 4 wires from the wire harness of the new motor, and use butt end connectors to reattach these wires to the corresponding wires in the unit. Total job took between 1 and 2 hours, and the motor change solved the noise problem.

I watched the video online and it said there were three sensors in the refrigerator, two in the freezer and one in the refrigerator. I only ordered one sensor and was going to try the one in the refrigerator first. He said the upper one in the freezer is the most difficult, but is usually the problem. So, I replaced the upper sensor and ... Read more tried restarting the unit. Everything went well and it fixed the problem.

No water flow after installation, part sent GSWF filter made in Taiwan had different treading then filter made in USA. Tried 3 from Taiwan same result. Found 1 from USA worked perfect.

replaced lights in refrigirator and freezer